Download
Share
Print this page
Monte Carlo Fan Company 8EEDR60 D Series Owner's Manual And Installation Manual
  1. Manuals
  2. Brands
  3. Monte Carlo Fan Company Manuals
  4. Fan
  5. 8EEDR60 D Series
  6. Owner's manual and installation manual

Monte Carlo Fan Company 8EEDR60 D Series Owner's Manual And Installation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Owner's Guide and Installation Manual
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
MODEL NUMBER:
To register your fixture, please visit our website www.montecarlofans.com
3 0 6 4 9 6 4
8EEDR60XXD Series Fan
ETL Model NO. : 8EEDR60(XXXXX)
RETAILER NAME:
RETAILER ADDRESS:
9.9 kgs
21.8 lbs
Total fan weight with light

Advertisement

loading
Need help?

Need help?

Do you have a question about the 8EEDR60 D Series and is the answer not in the manual?

Questions and answers

Related Manuals for Monte Carlo Fan Company 8EEDR60 D Series

Summary of Contents for Monte Carlo Fan Company 8EEDR60 D Series

  • Page 1 Owner’s Guide and Installation Manual 8EEDR60XXD Series Fan ETL Model NO. : 8EEDR60(XXXXX) Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: RETAILER ADDRESS: MODEL NUMBER: To register your fixture, please visit our website www.montecarlofans.com 9.9 kgs 21.8 lbs Total fan weight with light...

  • Page 2: Cautions And Warnings

    Note: Suitable for use in damp locations. Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers Customer Service 800-969-3347 Customer Service Center 7400 Linder Ave. Skokie, IL 60077 www.montecarlofans.com © 2016 Monte Carlo Fan Company 11/2016...
  • Page 3 Place downrod over canopy, canopy Partially loosen downrod set screws from cross pin from downrod. bottom cap and yoke cover. yoke at top of motor assembly. Thread lead wires and safety cable from motor assembly through downrod. © 2016 Monte Carlo Fan Company 11/2016...
  • Page 4 The splices after being made should be turned upward and pushed carefully up into the outlet box. © 2016 Monte Carlo Fan Company 11/2016...
  • Page 5 Note: Keep the safety cable with clamp plate. Twist clockwise till lock. Reinstall outside the slot, so it will be easier for the screw removed in step 15. Tighten all blanking plate installation in the step 21. screws securely. © 2016 Monte Carlo Fan Company 11/2016...
  • Page 6 Install blanking plate Light pan Blanking plate Threaded rod Align the threaded rod in blanking plate with the screw hole in light pan and Install it by turning clockwise till tight. © 2016 Monte Carlo Fan Company 11/2016...

  • Page 7: Transmitter Operation

    Or you may turn power off for 15 seconds then turn power back, and then turn the fan on, Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the fan or light load was increased abnormally. © 2016 Monte Carlo Fan Company 11/2016...
  • Page 8 4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal performance of this fan and it will take for few seconds to run this operation. © 2016 Monte Carlo Fan Company 11/2016...

  • Page 9: Troubleshooting

    Trouble Shooting Warning Trouble Suggested Remedy CAUTION CAUTION CAUTION © 2016 Monte Carlo Fan Company 11/2016...
  • Page 10 Nov.2016...