Related Manuals for pellenc 150P
Summary of Contents for pellenc 150P
- Page 1 Translation of the original op- erating instructions manual PELLENC POWER TOOLS BATTERY 150P 56_163476-B Operating instructions 05/2022 READ THE USER GUIDE CAREFULLY BEFORE USE...
-
Page 3: Table Of Contents
2. SAFETY ........................... 6 2.1. SAFETY MEASURES ASSOCIATED WITH THE USE OF THE TOOL ......... 2.2. SAFETY MEASURES ASSOCIATED WITH BATTERY USE ............2.3. SAFETY MEASURES WHEN USING THE "PELLENC" CHARGER ..........2.4. SAFETY SIGNAGE .......................... 3. DESCRIPTION AND TECHNICAL FEATURES ..............9 3.1. - Page 4 ......................10.1.2. COMMERCIAL WARRANTYPELLENC .................... 10.1.3. PAID AFTER-SALES SERVICE ...................... 11. COMPLIANCE STATEMENTS ................... 22 11.1. "EU" DECLARATION OF CONFORMITY: 150P BATTERY ............11.2. "EU" DECLARATION OF CONFORMITY: CHARGER CB5010HV ........... 11.3. "EU" DECLARATION OF CONFORMITY: CHARGER CB5004HV2 ......... 11.4. UK DECLARATION OF CONFORMITY : 150P BATTERY ...........
-
Page 5: Introduction
Refer to Section 2.4, “Safety signage” for the location diagram of the safety stickers affixed to the tool. No part of this manual may be reproduced without the written permission of the company PELLENC. The illustrations provided in this manual are for information purposes only and are in no way contractual. The PELLENC company reserves the right to make any modification or improvement to its products as deemed necessary without inform- ing customers already in possession of a similar model. -
Page 6: Safety
• Battery alone: product that is classified as class 9, UN3480. 14. Use of a battery other than that provided by Pellenc SA is dangerous (risk of serious injury). If a different battery is used, Pellenc SA cannot be held responsible for any consequences. -
Page 7: Safety Measures When Using The "Pellenc" Charger
In the event of contact with eyes, seek professional medical help. The liquid leaking from the batteries can cause irritations or burns. 19. Pellenc power tools must only be used with the battery units designed for the purpose. Use of other battery units can present a risk of injury and fire. -
Page 8: Safety Signage
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 2.4. SAFETY SIGNAGE California State Proposition 65: Caution This product contains or emits a chemical recognized by the State of California to cause cancer, birth defects or other reproductive harm. Independent Communications Au- thority of South Africa... -
Page 9: Description And Technical Features
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 3. DESCRIPTION AND TECHNICAL FEATURES 3.1. DESCRIPTION Charging connector Mode switch button Battery clip to be clipped onto the adjustable belt Increase button Tool power cord On/Off button Tool power cord connector HMI display screen Decrease button 10. -
Page 10: Commissioning
PELLENC POWER TOOLS BATTERY 150P 56_163476-B Charge percent- Type of charger 150P battery charging time age 150P battery 5 hrs 10 mins Charger CB5004HV2 (0.4 A) 100% 8h10 2hrs. 10min. Charger CB5010HV (1 A) 100% 3hrs. 50min. Important For the USA and Canada, use only the CB5010HV charger. - Page 11 PELLENC POWER TOOLS BATTERY 150P 56_163476-B Caution Before connecting the charger to the mains, check that your power system characteristics com- ply with the specifications given on the charger (see Section 3.3, “Technical characteristics - Charger”). When the battery is discharged, the tool stops automatically. The gauge display goes off, and the buzzer beeps once.
-
Page 12: Fitting The Holster To The Belt
PELLENC POWER TOOLS BATTERY 150P 56_163476-B Note After a long storage period (new battery, winter storage etc.), when you disconnect the charger, the charge level indicator may display a value of less than 99%. This is a normal phenomenon which can reoccur for up to 5 charge cycles with normal use between each charge. -
Page 13: Tool Connection
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 4.5. TOOL CONNECTION Note For more information on connecting the tool to the battery, refer to the tool's operating instructions manual. 4.6. PUTTING THE LEAD AND WRIST STRAP IN PLACE Put on the belt then clip the battery to it and in- stall the connected tool in the holster, see Sec- tion 4.4, “Fitting the holster to the belt”... -
Page 14: Using The Tool
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 5. USING THE TOOL Note For more information on the modes of use and "functional" settings, please refer to the tool operating instruc- tions. 5.1. AUTHORISATION MODES 5.1.1. CHANGE OF AUTHORISATION MODE Disconnect the tool and turn on the battery, Press the "mode"... -
Page 15: Maintenance
Battery check by an authorised deal- er PELLENC. Important Have the battery serviced every 400 hours or at least once a year by an authorised dealer PELLENC. Always store the charged and clean battery in a dry place. 6.2. CLEANING THE BATTERY Make sure that the battery is switched off, see Sec- tion 4.1, “Switching the battery on and off”. -
Page 16: Incidents And Troubleshooting
PELLENC POWER TOOLS BATTERY 150P 56_163476-B Clean the charger housing with a soft damp cloth. Important Cleaning shall be carried out with water only and without detergent, chlorine or sterilising solutions with an alkaline reaction. 7. INCIDENTS AND TROUBLESHOOTING 7.1. SUMMARY OF CHARGE INDICATOR AND BEEP MESSAGES... -
Page 17: Troubleshooting
PELLENC POWER TOOLS BATTERY 150P 56_163476-B Fault messages Charging Battery problem alternating and continuous beep Charger problem alternately 7.2. TROUBLESHOOTING... -
Page 18: Battery Replacement
PELLENC POWER TOOLS BATTERY 150P 56_163476-B Caution Never attempt to open or repair the battery pack or the charger. 7.3. BATTERY REPLACEMENT Important The battery must only be replaced and disposed of by an authorised distributor. 8. STORAGE AND TRANSPORT 8.1. -
Page 19: Warranties
The warranty is fully integral to the product sold by PELLENC. 10.1.2.1.2. SPARE PARTS The commercial warranty also covers original PELLENCspare parts, excluding labour and to the exclusion of certain... -
Page 20: Paid After-Sales Service
PELLENC Products are guaranteed under the commercial warranty as from delivery to the customer for a period of two (2) years for products connected to a PELLENC battery, and for a period of one (1) year for other PELLENC products. - Page 21 Paid after-sales service also covers original PELLENC spare parts, excluding labour and outside the legal and commercial warranty period. In case of replacement of original PELLENC spare parts in the context of after-sales service, said latter are covered by a warranty of one year as from the installation date.
-
Page 22: Compliance Statements
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 11. COMPLIANCE STATEMENTS 11.1. "EU" DECLARATION OF CONFORMITY: 150P BATTERY MANUFACTURER/ENTITY AUTHORISED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the product designated below as:... -
Page 23: Eu" Declaration Of Conformity: Charger Cb5010Hv
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 11.2. "EU" DECLARATION OF CONFORMITY: CHARGER CB5010HV MANUFACTURER/ENTITY AUTHORISED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the product designated below as: GENERIC DENOMINATION BATTERY CHARGER... -
Page 24: Eu" Declaration Of Conformity: Charger Cb5004Hv2
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 11.3. "EU" DECLARATION OF CONFORMITY: CHARGER CB5004HV2 MANUFACTURER/ENTITY AUTHORISED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the machine referred to below as: GENERIC DENOMINATION... -
Page 25: Declaration Of Conformity
THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the product referred to below as: GENERIC DENOMINATION BATTERY FUNCTION Intended to power PELLENC portable power tools COMMERCIAL NAME ULTRA LITHIUM BATTERY TYPE Li-ion battery MODEL 150P SERIAL No. -
Page 26: Declaration Of Conformity
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 11.5. UK DECLARATION OF CONFORMITY : CB5010HV CHARGER MANUFACTURER / ENTITY AUTHORIZED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the product referred to below as:... -
Page 27: Declaration Of Conformity
PELLENC POWER TOOLS BATTERY 150P 56_163476-B 11.6. UK DECLARATION OF CONFORMITY : CB5004HV2 CHARGER MANUFACTURER / ENTITY AUTHORIZED TO COMPILE PELLENC THE TECHNICAL FILE ADDRESS Quartier Notre-Dame - 84120 Pertuis (France) We hereby declare that the product referred to below as:... - Page 32 PELLENC Quartier Notre Dame - 84120 Pertuis (France)
Need help?
Do you have a question about the 150P and is the answer not in the manual?
Questions and answers