Table of Contents
Advertisement
1.3.2 Disassembly method
STEP
Fig.No.
PART
No.
1
COVER (UNDER)
Fig.1-3-1 (S1)
2
COVER (SHOE)
Fig.1-3-2 2(S2), (L2a), (L2b)
3
MIC COVER ASSY
4
UPPER CASE ASSY Fig.1-3-3a (SD CARD)
(Inc.MONITOR ASSY)
Fig.1-3-3b 2(S4b), (S4c), 2(S4b), 2(S4d) NOTE4c
5
MONITOR ASSY
Fig.1-3-4 2(S5a), GUIDE(MONI), 2(S5b) NOTE5
6
SHUTTER ASSY
FIig.1-3-5 (S6)
7
LOWER CASE ASSY Fig.1-3-6 CN 7a,CN 7b,SHEET(SHUTTER) NOTE7
(Inc.MICROPHONE,
E. VF UNIT,
AUDIO BOARD ASSY,
OP BLOCK ASSY)
8
MAIN BOARD ASSY Fig.1-3-7 SHEET(SHUTTER), 2(S8)
9
MECHANISM ASSY
0
MICROPHONE
Fig.1-3-8a HOOD, SPACER, (S#), (S@)
!
E. VF UNIT
@
AUDIO BOARD ASSY Fig.1-3-8b 2(S@b), SPACER, 3(S$)
#
OP BLOCK ASSY
$
SHOE ASSY
Table 1-3-2
Note: Remove the parts marked in
CONN.
CONNECTOR
No.
4
CN
a
MAIN
CN107
⇔
4
CN
b
MAIN
CN112
⇔
4
CN
c
MAIN
CN113
7
CN
a
MAIN
CN110
⇔
7
CN
b
MAIN
CN111
⇔
7
CN
c
MAIN
CN109
CN108 ← → EJECT SW
7
CN
d
MAIN
⇔
8
CN
a
MAIN
CN102
⇔
8
CN
b
MAIN
CN103
⇔
8
CN
c
MAIN
CN101
⇔
8
CN
d
MAIN
CN106
⇔
8
CN
e
MAIN
CN105
⇔
8
CN
f
MAIN
CN104
CN203 ← → MICROPHONE
0
CN
a
AUDIO
⇔
!
CN
a
AUDIO
CN204
⇔
#
CN
a
AUDIO
CN205
⇔
$
CN
a
AUDIO
CN202
Table 1-3-3
1-3
POINT
NOTE
—
—
(S3a), 2(S3b)
—
NOTE4a
(S4a), COVER (JIG)
NOTE4b
CN 4a
2(S4b), (S4e)
CN 4b, CN4c
NOTE
CN 7c, CN7d, 4(S7)
—
(L8a), SHIELD ASSY, CN 8a,
CN 8b, CN 8c, CN 8d
2(L8b), (L8c)
CN 8e, CN 8f
3(S9a),BRACKET(PRE/REC),
3(S9b),BRACKET(MECHA) ASSY
NOTE0
CN0a
(S!), SPACER, CN!a
NOTE!a
NOTE!b
NOET@a
NOET@b
CN #a
NOTE#a
NOTE#b
CN $a
NOTE$
.
Pin No.
BOTTOM
CN301
50
SUB OPE UNIT
-
7
MONITOR
CN401
39/33
AUDIO
CN201
120
CCD
-
20
OPE. COVER UNIT
-
13
-
2
LOADING MOTOR
-
6
ROTARY ENCODER
-
6
HEAD
-
8
SENSOR
-
16
CAPSTAN MOTOR
-
18
DRUM MOTOR
-
11
-
4
VF BL
CN7551
20
OP BLOCK ASSY
-
24
SHOE ASSY
-
16
4
NOTE
a: If a card is installed, remove it in advance.
4
NOTE
b: Be careful not to damage the battery removal switch.
When disassembling, ensure that the lock lever is in the
low position and set the battery removal switch only to
the up position.
4
NOTE
c: Take care of the removed screws.
5
Refer to Fig. 1-4-1 for the disassembly method.
NOTE
:
6
NOTE
:
Be careful not to damage or lose the parts.
7
NOTE
:
For the disassembly/assembly of the E. VF unit, AU-
DIO board assembly, and OP block assembly, see sec-
6
tion 1.8, "SERVICE KNOW-HOW".
0
NOTE
:
Leave the OP block assembly connected to the audio
board and locate it in a vacant space.
!
NOTE
a: Be careful not to cut the FPC wire or damage any of
the switches during work.
!
b: Refer to Fig. 1-5-1 for the disassembly method.
NOTE
@
a: Carefully proceed with the above-mentioned work not
NOTE
to damage any part.
@
#
$
NOTE
b,
a,
:
When assembling, attach the OP block assembly and
the shoe assembly on the AUDIO board assembly and
install them together in the lower case assembly.
#
b: Refer to Fig. 1-6-1 for the disassembly method.
NOTE
Advertisement
Table of Contents
