JVC GR-DVL767EG Service Manual
  1. Manuals
  2. Brands
  3. JVC Manuals
  4. Camcorder
  5. GR-DVL767EG
  6. Service manual

JVC GR-DVL767EG Service Manual

Hide thumbs Also See for GR-DVL767EG:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
GR-DVL767EG/EK,DVL865EG,DVL867EG
Regarding service information other than these sections, refer to the GR-DVL765EG service manual (No. 86670).
Also, be sure to note important safety precautions provided in the service manual.
SPECIFICATIONS
Power supply
: DC 11.0 V
DC 7.2 V
Power consumption
LCD monitor off, viewfinder on : Approx. 4.5 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 4.3 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
LCD monitor on, viewfinder off : Approx. 5.7 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 5.3 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Video light
: Approx. 2.8 W (GR-DVL867/DVL865/DVL767/DVL765)
Approx. 3.5 W (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Dimensions (W x H x D)
: 79 mm x 89 mm x 184 mm (GR-DVL867/DVL865/DVL767/DVL765)
79 mm x 89 mm x 167 mm (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
(with the LCD monitor closed and the viewfinder pushed down)
Weight
: Approx. 580 g (GR-DVL867/DVL865)
Approx. 570 g (GR-DVL767/DVL765/DVL567)
Approx. 560 g (GR-DVL367/DVL365)
Approx. 550 g (GR-DVL167/DVL160)
Operating temperature
: 0°C to 40°C
Operating humidity
: 35% to 80%
Storage temperature
: –20°C to 50°C
Pickup
: 1/3.8" CCD (GR-DVL867/DVL865/DVL767/DVL765)
1/4" CCD (GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Lens
: F 1.8, f = 3.8 mm to 38 mm, 10:1 power zoom lens
(GR-DVL867/DVL865/DVL767/DVL765)
F 1.8, f = 3.6 mm to 36 mm, 10:1 power zoom lens
(GR-DVL567/DVL367/DVL365/DVL167/DVL160)
Filter diameter
: ø37 mm
LCD monitor
: 3.5" diagonally measured, LCD panel/TFT active matrix system
(GR-DVL867/DVL865/DVL567)
2.5" diagonally measured, LCD panel/TFT active matrix system
(GR-DVL767/DVL765/DVL367/DVL365/DVL167/DVL160)
Viewfinder
: Electronic viewfinder with 0.24" black/white LCD
Speaker
: Monaural
Digital Video Camera
Format
: DV format (SD mode)
Signal format
: PAL standard
Recording/Playback format : Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit), 48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
: SP: 80 min.
(using 80 min. cassette)
LP: 120 min.
DIGITAL VIDEO CAMERA
(The specifications shown pertain specifically to the model GR-DVL160,DVL167,DVL365,
DVL367,DVL567,DVL765,DVL767,DVL865,DVL867)
Camcorder
General
(Using AC Adapter)
(Using battery pack)
This service manual is printed on 100% recycled paper.
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
Digital Still Camera Function
(GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only)
Storage media
: SD Memory Card/MultiMediaCard
Compression system
: Still image : JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
: 3 modes (1280 X 960 pixels*, 1024 x 768 pixels,
640 x 480 pixels)
Picture quality
: 2 modes (FINE/STANDARD)
Approximate number of
storable images
:
pg. 27.
* GR-DVL867/DVL865/DVL767/DVL765 only.
Connectors
S-Video
: Y:1 V (p-p), 75 Ω, analogue
Output
C:0.29 V (p-p), 75 Ω, analogue
AV
: 1 V (p-p), 75 Ω, analogue
Video output
Audio output
: 300 mV (rms), 1 kΩ, analogue, stereo
DV
Output
: 4-pin, IEEE 1394 compliant
Input (GR-DVL867/DVL767/
: 4-pin, IEEE 1394 compliant
DVL567/DVL367/DVL167 only)
USB (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365 only)
: 5-pin
PC (GR-DVL167/DVL160 only)
: ø2.5 mm, 3-pole
EDIT (GR-DVL867/DVL865/
DVL767/DVL765/DVL567/
DVL367/DVL365 only)
: ø3.5 mm, 2-pole
JLIP (GR-DVL167/DVL160 only) : ø3.5 mm, 4-pole
AC Adapter
Power requirement
: AC 110 V to 240 V`, 50 Hz/60 Hz
Output
: DC 11 V
Specifications shown are for SP mode unless otherwise indicated.
E & O.E. Design and specifications subject to change without notice.
, 1 A
No. 86686
April 2002

Advertisement

Table of Contents
loading

Related Manuals for JVC GR-DVL767EG

Summary of Contents for JVC GR-DVL767EG

  • Page 1 SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DVL767EG/EK,DVL865EG,DVL867EG Regarding service information other than these sections, refer to the GR-DVL765EG service manual (No. 86670). Also, be sure to note important safety precautions provided in the service manual. (The specifications shown pertain specifically to the model GR-DVL160,DVL167,DVL365,...
  • Page 2 PACKING AND ACCESSORY ASSEMBLY <M1> ..........................5-1 FINAL ASSEMBLY <M2> ..................................5-3 MONITOR ASSEMBLY <M5> [GR-DVL767EG-X/-Y/EK] ........................5-6 MONITOR ASSEMBLY <M5> [GR-DVL865EG-X,DVL867EG-X/-Y] ..................... 5-7 The following table indicate main different points between models GR-DVL765EG-X, GR-DVL767EG-X,GR-DVL767EG-Y, DVL767EK,DVL865EG-X,DVL867EG-X and GR-DVL867EG-Y. MODEL GR-DVL765EG-X GR-DVL767EG-X GR-DVL767EG-Y GR-DVL767EK GR-DVL865EG-X GR-DVL867EG-X GR-DVL867EG-Y...
  • Page 3 REF. MODEL GR-DVL765EG-X GR-DVL767EG-X GR-DVL767EG-Y GR-DVL767EK GR-DVL865EG-X GR-DVL867EG-X GR-DVL867EG-Y ITEM R3025 MG RESISTOR — NRSA6AJ-102W — NRSA6AJ-102W — R3040 MG RESISTOR NRSA6AJ-222W — — — NRSA6AJ-222W — NRSA6AJ-222W R3041 MG RESISTOR NRSA6AJ-561W — — — NRSA6AJ-561W — NRSA6AJ-561W R3042 MG RESISTOR NRSA6AJ-561W —...
  • Page 4 VICTOR COMPANY OF JAPAN, LIMITED S40894 VIDEO DIVISION Printed in Japan...
  • Page 5 SECTION 5 PARTS LIST SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. PACKING AND ACCESSORY ASSEMBLY <M1> The instruction manual to be provided with this product will differ according to the destination. FINAL ASSY <M2>...
  • Page 6 POLY BAG QPA02003506 POLY BAG,A,B,D,E,F YQM30061-3 POLY BAG,C LYT0909-002B INST.BOOK(GE),A,B,D,E,F LYT0909-003B INST.BOOK(FR),A,D,E LYT0909-004B INST.BOOK(DU),A,D,E LYT0909-005B INST.BOOK(SP),A,D,E LYT0909-006B INST.BOOK(IT),A,D,E MODEL MARK LYT0909-007A INST.BOOK(DA),B,F GR-DVL767EG-X LYT0909-008A INST.BOOK(FI),B,F GR-DVL767EG-Y LYT0909-009A INST.BOOK(SW),B,F GR-DVL767EK LYT0909-010A INST.BOOK(NO),B,F LYT0910-001B INST.BOOK(EN),C GR-DVL865EG-X LYT0912-001A INST.BOOK(SOFT.EN),C GR-DVL867EG-X LYT0912-002A INST.BOOK(SOFT.GE),A,B GR-DVL867EG-Y LYT0912-003A INST.BOOK(SOFT.FR),A...
  • Page 7 FINAL ASSEMBLY <M2> 140T 140F 140J 140U 140T 140R 140N 140H 140G 140T 140N 140S 140T 140S 140N 140R 140K 140E 140R 140S 140S 140C 140M 140P 140D 140A 140L 140L 140L 140L 140B RATING LABEL 251C 251D 251H 251D 170A 251H 251J...
  • Page 8 ELECTRONIC VIEWFINDER <M4> MECHANISM <M3> <10> MAIN <01> JACK <06> 130B 130A JUNCTION REAR <05> <07> MONITOR <02> 130F 130D 130E 130F 130F 130E 101K 101A 130C 101K 101J 101M 101H 101M 101C 101D 125E 101B 101C 125E 101L MONITOR <M5>...
  • Page 9 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 10 MONITOR ASSEMBLY <M5> [GR-DVL767EG-X/-Y/EK] 501H 501A 501G 501C 501J 501E 501D 501B 508E 501F 508C 501D LCD BL 508E <03> 508A 508F 508B 508D 508G 502A REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION...
  • Page 11 508E LY30018-058A SPECIAL SCREW,X2 501F LY43785-001A EARTH MON(3.5) 508F LY30018-023A SPECIAL SCREW 501G LY32704-002A WINDOW(M.MEGA) 508G LY30029-0Q5A SPACER(A) 501H LY32707-001B PLATE(M3.5MEGA) QYSPSPT1730R SCREW,X2 501J QLE0017-001 EL PANEL LY30018-0F2A SPECIAL SCREW,X2 LY30029-0Y6A SPACER(A) (Sanwa)-M2D229+/249/249+ E. & O. E. No. 86686 GR-DVL767EG-X/-Y/EK,DVL865EG-X,DVL867EG-X/-Y...
  • Page 12 SCHEMATIC DIAGRAMS DIGITAL VIDEO CAMERA GR-DVL767EG/EK,DVL865EG,DVL867EG CD-ROM No.SML200204 Regarding service information other than these sections, refer to the GR-DVL765EG service manual (No. 86670). Also, be sure to note important safety precautions provided in the service manual. (The specifications shown pertain specifically to the model GR-DVL160,DVL167,DVL365,...
  • Page 13 SECTION 4 CHARTS AND DIAGRAM MAIN CIRCUIT BOARD FOIL SIDE(B) [GR-DVL865EG-X,DVL867EG-Y] R1083 R1011 TL1038 R1058 R1012 TL1001 TL1036 TL1002 TL1003 C1013 R1080 R1036 C1038 R1044 R1045 R1027 C1017 R1047 R1046 C1015 R1029 R1023 Q1003 TL1004 TL1005 R1024 R1079 R1032 IC1005 R1082 R1031 RA4304...
  • Page 14 TL4202 C4203 C4201 L4301 L4305 L4302 L4303 C4202 C4204 A4301 R4320 R4302 C4314 C4216 C4309 R4205 C4214 R4204 R4203 C4213 C4212 IC4301 TL4201 TL4318 TL4319 C4206 C4207 C4208 R4317 C4210 X4301 R4301 0 1 MAIN PWB R4314 R4304 L4304 RA4306 R4315 R4312 L3802...
  • Page 15 COMPONENT PARTS LOCATION GUIDE <MAIN/YB10391-01-01> (1/2) REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C2024 C3043 C3806 C5006 C6703 L2001 C2025 C3044 C3807 C5007 C6704 L2002 C1003 C2026 C3045 C3808 C5008 L2101 C1004 CONNECTOR C2027 C3046...
  • Page 16 COMPONENT PARTS LOCATION GUIDE <MAIN/YB10391-01-01> (2/2) REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION Q3733 R1076 R2108 R3073 R4317 R6103 TL1005 Q3734 R1077 R2109 R3074 R4320 R6106 TL1007 Q3735 R1078 R2110 R3075 R4321 R6107 TL1009 Q4801 R1079...
  • Page 17 COMPONENT SIDE(A) C5002 C5001 C5009 R5017 C5011 L5003 L5001 C5007 TL5004 L5002 C5014 TL5002 R5003 IC5001 R5002 C5013 C5012 TL5001 C6118 C6119 C5006 C5025 C5005 R6116 C6120 D5001 R4323 C6121 L5006 C6122 C6123 C6124 C6126 C6125 C3714 R3714 R3715 L5004 C3706 C3707 0 1 MAIN PWB...
  • Page 18 IC1002 C6226 CN111 D6207 Q6213 R6234 R6241 C6230 Q6216 C6225 R6240 R6232 R6106 R6229 Q6212 R6103 R6237 C6109 R6247 C6108 R6009 C6107 R6227 R6221 R6223 C6219 C6218 C6215 R6226 C6216 R6222 C6106 R6224 R6225 D6002 C6130 R6219 R6220 TL1417 C6134 TL1415 L6207 L6206...
  • Page 19 DSC CIRCUIT BOARD FOIL SIDE(B) [GR-DVL865EG-X] 1 0 DSC PWB YB20931-01-01 R8031 R8073 Q8002 IC8004 R8075 R8027 D8001 IC8007 R8020 R8059 RA8001 RA8003 R8037 R8046 R8056 R8007 R8008 R8009 C8026 RA8002 RA8004 R8068 R8022 R8069 R8032 C8011 C8030 R8051 R8054 R8050 R8053 C8016...
  • Page 20 COMPONENT SIDE(A) 1 0 DSC PWB YB20931-01-01 CN8003 C8304 R8303 C8307 C8305 R8305 R8311 R8309 R8310 R8308 R8307 R8306 C8003 R8065 R8067 C8004 C8005 L8004 IC8003 COMPONENT PARTS LOCATION GUIDE <DSC/YB20931-01-01> (2/2) REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION R8032 B C 1A R8057...
  • Page 21 VICTOR COMPANY OF JAPAN, LIMITED S40894 VIDEO DIVISION Printed in Japan...
  • Page 22 SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DVL765EG (The specifications shown pertain specifically to the model GR-DVL160,DVL167,DVL365, SPECIFICATIONS DVL367,DVL567,DVL765,DVL767,DVL865,DVL867) Digital Still Camera Function Camcorder (GR-DVL867/DVL865/DVL767/DVL765/DVL567/DVL367/DVL365 only) Storage media : SD Memory Card/MultiMediaCard General Compression system : Still image : JPEG (compatible) Moving image : MPEG4 (compatible) Power supply : DC 11.0 V (Using AC Adapter)

  • Page 23: Table Of Contents

    TABLE OF CONTENTS Section Title Page Section Title Page Important Safety Precautions 3. ELECTRICAL ADJUSTMENT 3.1 PRECAUTION ............... 3-1 INSTRUCTIONS 3.2 SETUP .................. 3-2 1. DISASSEMBLY 1.1 BEFORE ASSEMBLY AND DISASSEMBLY ......1-1 1.1.1 Precautions ..............1-1 4. CHARTS AND DIAGRAMS 1.1.2 Assembly and disassembly ..........

  • Page 24: Important Safety Precautions

    Important Safety Precautions Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 25 • Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

  • Page 26: Disassembly

    SECTION 1 DISASSEMBLY 1.1 BEFORE ASSEMBLY AND DISASSEMBLY 1.1.4 Disconnection of connectors (Wires) 1.1.1 Precautions Connector Pull both ends of the connector in the arrow direction, re- 1. Be sure to remove the power supply unit prior to mount- move the lock and disconnect the flat wire. ing and soldering of parts.

  • Page 27: Jigs And Tools Required For Disassembly, Assembly And Adjustment

    1.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, 1.3 DISASSEMBLY/ASSEMBLY OF CABINET PARTS ASSEMBLY AND ADJUSTMENT AND BOARD ASSEMBLY 1.2.1 Tools required for adjustments 1.3.1 Disassembly flow chart This flowchart indicates the disassembly step for the cabi- Torque driver YTU94088 YTU94088-003 net parts and board assembly in order to gain access to item(s) to be serviced.

  • Page 28: Disassembly Method

    1.3.2 Disassembly method Note: Remove the parts marked in STEP CONN. Fig.No. PART POINT NOTE CONNECTOR Pin No. ⇔ UPPER CASE Fig. 1-3-1 6(S1a), 4(S1b), 3(S1c), MAIN CN101 MONITOR CN761 ASSY ⇔ CN2a DSC CN8002 MONITOR CN762 (Inc. MONITOR – ASSY / E.VF CN2b DSC CN8001...
  • Page 29 Fig. 1-3-2 Fig. 1-3-4 NOTE KNOB (VIDEO-DSC) KNOB (DC LIGHT) ∗ SPEAKER ∗ BRACKET (MONITOR) ∗ : 0.147N·m (1.5kgf·cm) Fig. 1-3-5 Fig. 1-3-3...
  • Page 30 NOTE COVER (JACK) DC LIGHT DC LIGHT Fig. 1-3-6 NOTE NOTE NOTE COVER TO MAIN (DC) TO CCD Fig. 1-3-7 Fig. 1-3-8...
  • Page 31 SHIELD PLATE Fig. 1-3-9 Fig. 1-3-11 BRACKET (MECHA) NOTE EJECT SW NOTE Fig. 1-3-10 Fig. 1-3-12...

  • Page 32: Monitor Assembly

    MONITOR ASSEMBLY 3. Unplug the wires and FPCs from the two connectors ( c , d ) and then remove the LCD BL board assembly, holder 1.4.1 Disassembly/assembly of monitor assembly (PWB) and backlight in that order. (for 2.5”-type LCD) 4.

  • Page 33: Vf Assembly

    E. VF ASSEMBLY 1.5.1 Disassembly/assembly of E.VF assembly (for the B/W VF) 1. Remove the EYE CUP. 5. Remove the screw (8) and the remove the CAP (VF). 2. Remove the three screws (1 to 3) and then remove the 6.

  • Page 34: Disassembly/Assembly Of 0 Op Block Assembly/Ccd Board Assembly

    1.6 DISASSEMBLY/ASSEMBLY OF 0 OP BLOCK 1.6.3 How to assemble CCD base assembly and CCD ASSEMBLY/CCD BOARD ASSEMBLY board assembly 1. Install the optical LPF with the spacer rubber attached 1.6.1 Precautions to its CCD side in the OP block assembly. 1.

  • Page 35: Emergency Display

    1.7 EMERGENCY DISPLAY Whenever some abnormal signal is input to the syscon CPU, Example (in case of the error number E01): an error number (E01, as an example) is displayed on the LCD monitor or (in the electronic view finder). In every error status, such the message as shown below alternately appear over and over.

  • Page 36: Service Note

    1.8 SERVICE NOTE 1-11...

  • Page 37: Mechanism Adjustment

    SECTION 2 MECHANISM ADJUSTMENT 2.1 PRELIMINARY REMARKS ON ADJUSTMENT AND (3) The symbol (T or B)appearing in this column shows the REPAIR side which the objective part is mounted on. T =the upper side, B =the lower side 2.1.1 Precautions (4) Symbols appearing in this column indicate drawing 1.

  • Page 38: Jigs And Tools Required For Disassembly, Assembly And Adjustment

    2.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, ASSEMBLY AND ADJUSTMENT 2.2.1 Tools required for adjustments 1. Torque driver Torque driver YTU94088 YTU94088-003 Be sure to use to fastening the mechanism and exterior parts because those parts must strictly be controlled for tightening torque.

  • Page 39: Disassembly/Assembly Of Mechanism Assembly

    2.3 DISASSEMBLY/ASSEMBLY OF MECHANISM <SUB CAM GEAR> ASSEMBLY 2.3.1 General statement The mechanism should generally be disassembled/assem- bled in the EJECT mode (ASSEMBLY mode). (Refer to Fig. 2-3-1.) TOP VIEW BOTTOM VIEW However, when the mechanism is removed from the main body, it is set in the STOP mode.

  • Page 40: Mechanism Timing Chart

    2.3.3 Mechanism timing chart MODE EJECT C IN SHORT FF STOP PLAY PARTS MAIN CAM (ø10.4) 31.7 45.6 49.5 74.04 129.5 156.6 169.2 211.5 280.3 SUB CAM (ø11) 43.1 46.8 122.5 148.1 ENCODER (ø10) 47.4 51.5 134.7 162.9 291.5 ROTARY ENCODER CAM SW SLIDE END...

  • Page 41: Disassembly/Assembly Of Mechanism Assembly

    2.4 DISASSEMBLY/ASSEMBLY OF MECHANISM ASSEMBLY 2.4.1 Follow chart 1. Configuration Mechanism assembly Cassette housing assembly Slide deck assembly Main deck assembly Fig. 2-4-1 2. Procedures for disassembly Mechanism assembly Cassette housing assembly Slide deck assembly Main deck assembly Fig. 2-4-2...
  • Page 42 3. Disassembling procedure table PART NAME FIG. POINT NOTE REMARKS A Cassette housing assembly Fig. 2-4-5 3(S1),(L1a)-(L1d) 1a, 1b, 1c, 1d Adjustment Reel disk (SUP) assembly Fig. 2-4-6 (W2) 2a, 2b Reel disk (TU) assembly Fig. 2-4-6 (W2) 2a, 2b Reel cover assembly Fig.
  • Page 43 < TOP VIEW > 4b 11b 11a Main deck assembly Slide deck assembly 7b 7a 7d 7e 9c 3c 3b 7h 2b Fig. 2-4-3 < BOTTOM VIEW > Main deck assembly Slide deck assembly Fig. 2-4-4...

  • Page 44: Disassembly/Assembly

    2.4.2 Disassembly/assembly Note 1a: <STOP mode> Shift the mechanism mode 1. A Cassette housing assembly from the STOP mode to the EJECT mode. Cassette Note 1b: housing Reassemble the cassette (L1b) assembly housing assembly to the (S1) mechanism as the cancel lever is moved in the direc- tion of the arrow.
  • Page 45 3. 3a Tension arm assembly/ 3b Release guide assembly 3c Idler arm assembly/ 3d Guide arm assembly 3e Pinch roller arm assembly Note 3a: When removing the reel cover assembly, pay heed to re- lease guide assembly and guide arm assembly. For the (W3a) guide arm assembly is just inserted into the slide deck as- sembly from the upside and it is apt to come off after the...
  • Page 46 5. 5a Guide roller (S) assembly/ 5b Rail assembly Note 5a: When reassembling, insert the tip Guide roller of the guide roller with the coil (s) assembly spring put on it into the hole on the main deck. Tighten the guide roller by about 6 turns so that the Note 5a (P5)
  • Page 47 Note 7a: 7. 7a Loading brake assembly/ 7b Guide pin (S) Don’t remove these parts unreasonably. If they are removed 7c Pad arm assembly/ 7d Slide guide plate assembly for some reason, be very careful not to lose them. 7e Collar/ 7f Collar/ 7g Sub brake assembly 7h Control plate assembly Note 7b: When reinstalling the sub brake assembly, set the control...
  • Page 48 9. 9a Loading guide/ 9b Timing belt 9c Center gear assembly/ 9d Motor bracket assembly 9e Worm wheel/ 9f Gear holder Note 9a: Note 9b Note 9a Carefully handle the DEW sensor. (Don’t touch the sensor surface in particular.) Note 9b: When engaging the timing belt, make sure that it securely (S9) engages with the gears of both the center gear assembly and...
  • Page 49 11. 11a Catcher (T) assembly/ 11b Capstan motor 11c Charge arm assembly/ 11d Sub cam gear 11e PWB holder Note 11: The following figure shows how to put the charge arm as- sembly and sub cam gear assembly together. (S11) (S11) Note 11 (W11)

  • Page 50: List Of Procedures For Disassembly

    2.4.3 List of procedures for disassembly Cassette housing assembly (P5) (L1b) (S9) (W5a) (S9) (W5b) (W5a) (W3b) (S1) (W5a) (W10b) (L1d) (L1a) (S4) (S4) (S4) (S1) (L1c) (S1) (S11) (W10a) (S10) (S11) (S10) (W10a) (S11) (S9) (S11) (W9) (W4) (P4b) (P4a) (S9) (W7)

  • Page 51: Checkup And Adjustment Of Mechanism Phase

    2.5 CHECKUP AND ADJUSTMENT OF MECHANISM PHASE <Connect gear> (Note 2) Set the connect gear so <Rotary encoder> that its locating hole meets Set the “I” of the rotary the hole on the main deck part at the tapped hole assembly.

  • Page 52: Mechanism Adjustments

    2.6 MECHANISM ADJUSTMENTS 2.6.1 Assembling slide deck assembly and main deck assembly œ Œ Fig. 2-6-1 Assembling procedure 1. Loosen the screw A. 2. Set the mechanism in the PLAY mode. (Refer to “2.3.2 Explanation of mechanism mode”.) 3. Press the end face B of the slide deck assembly (reel disk side) and the end face C of the main deck assem- bly (drum assembly side) with uniform force so that the two assemblies are tightly pressed to each other.

  • Page 53: Locating Tension Pole

    2.6.2 Locating tension pole <PLAY mode> Fig. 2-6-2 Locating procedure 1. Enter the mechanism assembly into the PLAY mode. (Refer to “2.3.2 Explanation of mechanism mode”.) 2. When the “ ” part is positioned down, make sure that the part “a” of the tension arm assembly is located within the range of “b”.

  • Page 54: Service Note

    2.7 SERVICE NOTE Use the following chart to manage mechanism parts that are removed for disassembling the mechanism. Cassette housing assembly S1×3 Reel disk (SUP) assembly Reel cover assembly W2×1 Reel disk (TU) assembly W2×1 S2b×1 S2a×2 W2×1 Guide arm Tension arm Pinch roller arm Release guide...
  • Page 55 Slide deck assembly Loading Slide guide Guide pin Pad arm brake plate assembly assembly assembly W7×1 P7a×1 S7a×1 W7×1 P7b×1 S7b×1 Control Collar Collar Sub brake plate assembly assembly W7×1 P7c×1 W7×2 P7d×1 W6×1 Main deck assembly Slide lever Tension lever Brake control assembly assembly...

  • Page 56: Compatibility Adjustment

    2.8 COMPATIBILITY ADJUSTMENT 2.8.1 Jig connector cable connection Remove one screw (1) first and the cover (JIG) next. Jig connector cable (YTU93082C) Jig board CN105 Cover(JIG) Fig. 2-8-1 Jig connector cable connection MAIN CN105 JIG BOARD VPPC REG_3V SRV_TX SRV_TX CJIG_RST CJIG_RST IF_TX...

  • Page 57: Tape Pattern Check

    2.8.2 Tape pattern check (1) Play back the compatibility adjustment tape. (2) While triggering the MAIN CN105-21PIN (HID1), ob- CN105 serve the waveform of CN105-20PIN (ENV_OUT). (ENV_OUT) (3) Confirm that the waveform is free from remarkable level-down, and entirely parallel and straight. Moreover, perform the following adjustment as re- CN105 quired.

  • Page 58: Electrical Adjustment

    SECTION 3 ELECTRICAL ADJUSTMENT 3.1 PRECAUTION 3. Tools required for adjustments 1. Precaution Torque driver Both the camera and deck sections of this model needs a YTU94088 YTU94088-003 personal computer for adjustment except simple adjustment with potentiometers. If some of the following parts is replaced for repair or other reason, the repaired set must be adjusted with a personal computer.

  • Page 59: Setup

    Torque driver Alignment tape Be sure to use to fastening the mechanism and exte- To be used for check and adjustment of interchange- rior parts because those parts must strictly be control- ability of the mechanism. led for tightening torque. 10.

  • Page 60: Packing And Accessory Assembly

    SECTION 5 PARTS LIST SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ******************************...
  • Page 61 FINAL ASSEMBLY <M2> 140T ELECTRONIC 140F 140J VIEWFINDER 140U <M4> MECHANISM <M3> 140T 140R 140N 140H <10> 140T 140G 140N 140S 140T 140S 140N 140R 140K 140E 140R MAIN 140S <01> 140S 140C 140M 140P JACK 140D <06> 140A 140L 130B 130A JUNCTION 140L...

  • Page 62: Final Assembly

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 63 MECHANISM ASSEMBLY <M3> NOTE:The section marked in AA and BB indicate Classification Part No. Symbol in drawing lubrication and greasing areas. Grease KYODO-SH-JB YTU94027...

  • Page 64: Mechanism Assembly

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 65: Electronic Viewfinder Assembly

    ELECTRONIC VIEWFINDER ASSEMBLY <M4> 324B 324A 334 306 B/W VF <08> REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 66: Monitor Assembly

    MONITOR ASSEMBLY <M5> 501H 501A 501G 501C 501J 501E 501D 501B 508E 501F 508C 501D LCD BL 508E <03> 508A 508F 508B 508D 508G 502A REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 67: Electrical Parts List

    ELECTRICAL PARTS LIST REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 68 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 69 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 70 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 71 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 72 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 73 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 74 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 75: Monitor Board Assembly <02

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 76: Lcd Bl Board Assembly <03

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 77: Junction Board Assembly <05

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

  • Page 78: Dsc Board Assembly <10

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 79 SECTION 4 CIRCUIT BOARD NOTES CHARTS AND DIAGRAMS 1. Foil and Component sides 1) Foil side (B side) : NOTES OF SCHEMATIC DIAGRAM 4. Voltage measurement Parts on the foil side seen from foil face (pattern face) 1) Regulator (DC/DC CONV) circuits are indicated.
  • Page 80 BOARD INTERCONNECTIONS YTU94074-20 YTU94074-6 ∗ ∗ YTU94077-6 J501 J502 J503 YTU94077-20 JLIP ∗ CN501 CN107 CAPSTAN MOTOR DRUM MOTOR LOADING MOTOR HEAD ROTARY NOTE ) : The number of patch cords IN/OUT ENCODER MECHA SENSOR are indicated by interconnected. R.E.SW CAM_SW_A CAM_SW_B CAM_SW_C...
  • Page 81 MAIN IF SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from TO DSC CN8001 this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. CN105 TO SYSCON VPPC...
  • Page 82 SYSCON SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 1 MAIN (SYSCON) TO D.CPU SRV_RST...
  • Page 83 D.CPU SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN (D.CPU) L1401 TO REG...
  • Page 84 NOTES : For the destination of each signal and further line connections that are cut off from MDA SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 1 MAIN (MDA) TO D.CPU LD_REV...
  • Page 85 AUDIO SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 1 MAIN (AUDIO) R2029 MAIN IF...
  • Page 86 NOTES : For the destination of each signal and further line connections that are cut off from DVMAIN SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN (DVMAIN) C3041 C3040...
  • Page 87 NOTES : For the destination of each signal and further line connections that are cut off from PRE/REC SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN (PRE/REC) TO D.CPU...
  • Page 88 VIDEO I/O SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN (VIDEO I/O) L3701 10µ...
  • Page 89 4.10 CDS SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 1 MAIN (CDS) TO TG ADCLK...
  • Page 90 4.11 CAMERA DSP SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. L4304 [54MHz_CXO] NQR0129-002X...
  • Page 91 NOTES : For the destination of each signal and further line connections that are cut off from 4.12 OP DRIVER SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. IC4807 ∗...
  • Page 92 4.13 TG SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO SYSCON 0 1 MAIN (TG) TG_RST...
  • Page 93 NOTES : For the destination of each signal and further line connections that are cut off from 4.14 REG SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 1 MAIN (REG) MAIN IF CN105 SYSCON...
  • Page 94 4.15 MONITOR SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO B/W VF CN7001 CN763...
  • Page 95 4.16 LCD BL SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 3 LCD BL R751 C752...
  • Page 96 4.17 CCD SCHEMATIC DIAGRAM 4.18 JUNCTON SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS".
  • Page 97 4.19 JACK SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. JACK R501 C501...
  • Page 98 4.20 REAR SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. REAR R551 0Ω...
  • Page 99 NOTES : For the destination of each signal and further line connections that are cut off from 4.21 B/W VF SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. 0 8 B/W VF R7011 3.3k...
  • Page 100 NOTES : For the destination of each signal and further line connections that are cut off from 4.22 DSC SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. CN8001 1 0 DSC (DSC) 44.1KHZ...
  • Page 101 NOTES : For the destination of each signal and further line connections that are cut off from 4.23 USB SCHEMATIC DIAGRAM [THIS SCHEMATIC DIAGRAM IS NOT USED] this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. OPEN 1 0 DSC (USB) TO DSC...
  • Page 102 4.24 MAIN CIRCUIT BOARD FOIL SIDE (B) TL4202 C4203 R1083 TL1038 R1058 R1011 R1012 C4201 TL1001 TL1036 TL1002 TL1003 C1013 R1080 R1036 C1038 R1044 R1045 R1027 C1017 R1047 L4301 L4305 L4302 L4303 C1015 R1029 R1046 C4202 R1023 Q1003 TL1004 TL1005 R1024 C4204 R1079...
  • Page 103 COMPONENT PARTS LOCATION GUIDE <MAIN/YB10391> (1/2) REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C2024 C3043 C3806 C5006 C6703 L2001 C2025 C3044 C3807 C5007 C6704 L2002 C1003 C2026 C3045 C3808 C5008 L2101 C1004 CONNECTOR C2027 C3046...
  • Page 104 COMPONENT PARTS LOCATION GUIDE <MAIN/YB10391> (2/2) REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION R6103 TL1005 Q3733 R1076 R2108 R3073 R4317 Q3734 R1077 R2109 R3074 R4320 R6106 TL1007 Q3735 R1078 R2110 R3075 R4321 R6107 TL1009 Q4801 R1079...
  • Page 105 COMPONENT SIDE (A) C5002 C5001 C5009 R5017 C5011 IC1002 L5003 C6226 L5001 C5007 TL5004 CN111 D6207 L5002 Q6213 C5014 TL5002 R6234 R6241 IC5001 R5003 C6230 Q6216 C6225 R6240 R5002 R6232 R6106 C5013 R6229 Q6212 C5012 TL5001 C6118 R6103 R6237 C6119 C6109 R6247 C5006...
  • Page 106 4.25 MONITOR CIRCUIT BOARD FOIL SIDE (B) COMPONENT SIDE (A) ZP1-39 ZP4-33 ZP1-5 R7638 R7640 R7643 ZP1-13 R7636 R7602 IC7604 IC7101 C7606 C7614 R7601 ZP3-9 C7615 R7645 C7605 R7637 ZP3-13 R7630 C7604 ZP3-17 R7603 R7629 ZP3-18 C7602 C7618 ZP4-18 C7603 ZP3-19 Q7607 C7620...
  • Page 107 4.26 LCD BL CIRCUIT BOARD FOIL SIDE (B) COMPONENT SIDE (A) 0 3 LCD BL PWB 0 3 LCD BL PWB YB10325-01-03 YB10325-01-03 CN754 IC751 C752 C752P C751P C751 L752 C7505 C7505P F751 F751 Q7502 R7503 C7506 R7505 R7504 C7507 R7508 C7503 Q7505...
  • Page 108 4.27 CCD AND JUNCTION CIRCUIT BOARDS - CCD - - JUNCTION - FOIL SIDE (B) COMPONENT SIDE (A) FOIL SIDE (B) 0 5 JUNCTION PWB 0 5 JUNCTION PWB YB10358-01-01 YB10358-01-01 0 4 CCD PWB YB20914-01-01 IC5201 COMPONENT SIDE (A) Q5202 0 4 CCD PWB C5201...
  • Page 109 4.28 JACK AND VF CIRCUIT BOARDS - JACK - - VF - FOIL SIDE (B) FOIL SIDE (B) 0 8 VF PWB 0 6 JACK PWB YB20910 YB10357-01-01 ZP1-2 R7001 ZP1-3 R7012 R7005 ZP1-4 D502 R7013 C513 C505 R509 L506 C514 D505 C510...
  • Page 110 4.29 REAR CIRCUIT BOARD FOIL SIDE (B) COMPONENT SIDE (A) R552 TL554 L551 L552 R560 R562 R554 D551 R555 R557 0 7 REAR PWB R558 0 7 REAR PWB YB10362-01-01 R559 YB10362-01-01 R556 D552 C551 D553 J554 TL551 TL553 TL552 4-59 4-60...
  • Page 111 4.30 DSC CIRCUIT BOARD 1 0 DSC PWB 1 0 DSC PWB FOIL SIDE (B) COMPONENT SIDE (A) YB20931 YB20931 C8304 R8303 R8031 C8307 R8073 C8305 R8305 Q8002 IC8004 R8311 R8075 R8309 R8310 R8027 D8001 R8308 R8307 IC8007 R8306 R8020 R8059 RA8001 RA8003...
  • Page 112 4.31 VOLTAGE CHARTS <SYSCON> <MDA> <DVMAIN> <VIDEO I/O> <CDS> <OP DRIVER> MODE MODE MODE MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO.
  • Page 113 <REG> <JACK> <CCD> <B/W VF> MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. IC6001 IC501 IC5201 IC7001 IC6101 Q5201 Q6001 Q5202 Q4801 Q5203 Q6002 Q4802...
  • Page 114 <LCD BL> <MONITOR> MODE MODE MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. IC751 IC7101 Q7501 IC7601 Q7502 IC7604 Q7503 12.0 Q7504 Q7101 Q7102...
  • Page 115 4.32 POWER SYSTEM BLOCK DIAGRAM MAIN REAR CN552 CN104 BATT_ BATT_ BATT. TERM OP BLOCK CAMERA DSP CN107 CN5201 CCD_15V Q5201 REG_3V CCD_15V IC4303 IC4301 REG_15V ADP_DC IN REG_2.5V CN551 CN103 ADP_H REG-CCD IC5001 2.5V REG CN552 CN104 Q6208 F6101 L6102 IC5201 ADP_DC...
  • Page 116 4.33 VIDEO SYSTEM BLOCK DIAGRAM IC4301 (CAMERA DSP) MAIN DCI0 IC5201 IC4201(CDS/AGC/AD) Q5201 DCI3 (CCD) CN5201 CN107 ADIN0~ADIN9 ADIN9 Vout CDSIN KIZU DYI0 BLOCK ADIN0 CONV DYI3 Q5202 DCO0 TG_36M CLK36I DCO3 CPOB OBCP DYO0 VDIN VDTG HDIN DYO3 HDTG CLK9A CLK9AO CLK27AO...
  • Page 117 IC3001(DVMAIN) IC3501 MAIN HID3 HID3 D.CPU YSO0 VIDEO I/F COMPRESS OUTER ECC INNER ECC PB_H YSO3 RECH (VBID DET (DCT,VLC (ENC/DET) (SUB/AUX) (ENC/DEC) FSPLLCTL REC_H PWMAUDIO RAM) VLD WORK REC_CTL RECCTL BRSO0 RAM) HID1 REC_DATA HID1 BRSO3 FORMATTER RECDATA REC_CLK (Formatting RECCLK REC_CLK...
  • Page 118 4.34 REGULATOR SYSTEM BLOCK DIAGRAM MAIN(REG) REAR CN552 CN104 BATT_+ BATT_+ BATT.TERM ADP_DC ADP_DC Q6207 CN106 L6205 ADP_DC LAMP_4.5V H :ON Q6002(1/2) R6004 R6001 POWER OFF:ON R6002 LAMP ON H :ON CN551 CN103 Q6217 ADP_DC IN BATT_CHK IC6001 BATT DC DET F6101 T_BATT at POWER OFF...

This manual is also suitable for:

Gr-dvl767ekDvl865egDvl867eg

Table of Contents