Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
GR-DVP3A-GY/A-SL/EA/ED/SH
Regarding service information other than these sections, refer to the GR-DVP3EG service manual (No. 86631).
Also, be sure to note important safety precautions provided in the service manual.
SPECIFICATIONS
(The specifications shown pertain specifically to the model GR-DVP3A-GY/A-GYC/A-SL/EA/ED/SH)
For General
Power supply
: DC 6.3 V } (Using AC Power Adapter/Charger)
DC 7.2 V } (Using battery pack)
Power consumption
LCD monitor off, viewfinder on
: Approx. 4.1 W
LCD monitor on, viewfinder off
: Approx. 5.0 W
Dimensions (W x H x D)
: 43 mm x 115 mm x 80 mm
(with the LCD monitor closed and the viewfinder pushed back in)
Weight
: Approx. 340 g (without grip belt, battery and cassette)
Approx. 410 g (incl. grip belt, battery and cassette)
Operating temperature
: 0°C to 40°C
Operating humidity
: 35% to 80%
Storage temperature
: –20°C to 50°C
Pickup
: 1/4" CCD
Lens
: F 1.8, f = 3.7 mm to 37 mm, 10:1 power zoom lens
(It is not possible to attach any lens filter or conversion lens.)
LCD monitor
: 2" diagonally measured, LCD panel/TFT active matrix system
Viewfinder
: Electronic viewfinder with 0.44" colour LCD
Speaker
: Monaural
For Digital Video Camera
Format
: DV format (SD mode)
Signal format
: PAL standard
Recording/Playback format
: Video: Digital component recording
: Audio: PCM digital recording, 32 kHz 4-channel (12-bit),
48 kHz 2-channel (16-bit)
Cassette
: Mini DV cassette
Tape speed
: SP: 18.8 mm/s
LP: 12.5 mm/s
Maximum recording time
: SP: 80 min.
(using 80 min. cassette)
LP: 120 min.
For Digital Still Camera
Storage media
: SD Memory Card/MultiMediaCard
Compression system
: Still image : JPEG (compatible)
Moving image : MPEG4 (compatible)
File size
: 2 modes (XGA: 1024 x 768 pixels/VGA: 640 x 480 pixels)
Picture quality
: 2 modes (FINE/STANDARD)
Approximate number of storable images
(with the provided memory card [8 MB], with Sound Effects pre-stored)
FINE
: 37 (VGA), 16 (XGA)
STANDARD
: 105 (VGA), 51 (XGA)
For other memory cards, see pg. 17.
DIGITAL VIDEO CAMERA
Camcorder
This service manual is printed on 100% recycled paper.
COPYRIGHT © 2001 VICTOR COMPANY OF JAPAN, LTD.
For Connectors
AV
: 1 V (p-p), 75 Ω, analogue
Video output
Audio output
: 300 mV (rms), 1 kΩ, analogue, stereo
DV
Input/output
: 4-pin, IEEE 1394 compliant
AC power adapter/charger AA-V100A, AA-V100EA, AA-V100ED or AA-V100SH
Power requirement
: AC 110 V to 240 V`, 50 Hz/60 Hz
Power consumption
: 23 W
Output
Charge
: DC 7.2 V } , 1.2 A
VTR
: DC 6.3 V } , 1.8 A
Dimensions (W x H x D)
: 68 mm x 44 mm x 110 mm
Weight
: Approx. 250 g (AA-V100A)
Approx. 260 g (AA-V100EA)
Approx. 250 g (AA-V100ED)
Approx. 325 g (AA-V100SH)
Docking Station CU-V507U
For General
Dimensions (W x H x D)
: 48.4 mm x 36 mm x 79 mm
Weight
: Approx. 53 g
For Connectors
PHONE
Headphone output
: ø3.5 mm, stereo
USB
: TYPE B
: Y: 1 V (p-p), 75 Ω, analogue output
S-VIDEO OUT
C: 0.29 V (p-p), 75 Ω, analogue output
EDIT
: ø3.5 mm, 2-pole
Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications
subject to change without notice.
No. 86646
June 2001

Advertisement

Table of Contents
loading

Summary of Contents for JVC GR-DVP3EG

  • Page 1 SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DVP3A-GY/A-SL/EA/ED/SH Regarding service information other than these sections, refer to the GR-DVP3EG service manual (No. 86631). Also, be sure to note important safety precautions provided in the service manual. SPECIFICATIONS (The specifications shown pertain specifically to the model GR-DVP3A-GY/A-GYC/A-SL/EA/ED/SH)
  • Page 2 EJECT CIRCUIT BOARD ............................. 4-5 5. PARTS LIST (5-1 to 5) PACKING AND ACCESSORY ASSEMBLY <M1> ......................5-1 FINAL ASSEMBLY <M2> .............................. 5-3 The following table indicate main different points between models GR-DVP3EG, GR-DVP3A-SL, GR-DVP3A-GY, GR-DVP3A-GYC, GR-DVP3EA, GR-DVP3ED and GR-DVP3SH. MODEL GR-DVP3EG...
  • Page 3 REF. MODEL GR-DVP3EG GR-DVP3A-SL GR-DVP3A-GY GR-DVP3A-GYC GR-DVP3EA GR-DVP3ED GR-DVP3SH ITEM SPECIAL SCREW LY30018-065A LY30018-0A2A LY30018-065A LY30018-0A2A SPECIAL SCREW LY30018-0A3A LY30018-060A LY30018-0A3A LY30018-060A SPACER(A) — — — — *LY30029-0R1A — — CASSETTE COVER LY20757-001B LY20757-002A LY20757-001B LY20757-002A SPECIAL SCREW LY30018-0E3A LY30018-006B LY30018-0E3A...
  • Page 4 VICTOR COMPANY OF JAPAN, LIMITED S40894 VIDEO DIVISION Printed in Japan...
  • Page 5 SECTION 4 CHARTS AND DIAGRAMS TO REG CON BOTTOM SCHEMATIC CN107 DIAGRAM CN301 TO J301 RS-151-X BOTTOM D2812 TO MMC/SD CN303 D2803 D2804 C2807 D2809 D2805 D2806 C2805 D2810 D2811 D2807 NO WEAR...
  • Page 6 NOTE 1. How to find the page showing the continuative schematic diagram. Example) To SYSCON : Refer to the GR-DVP3EG service manual (No. 86631). To SYSCON : Refer to this service manual. 2. The mark means modified points. 3. When ordering parts, be sure to order according to the Part Number indicated in the Parts List.
  • Page 7 BOTTOM CIRCUIT BOARD FOIL SIDE ( B ) BOTTOM PWB YB10329-01-02...
  • Page 8 COMPONENT SIDE ( A ) CN301 CN302 BOTTOM PWB YB10329-01-02...
  • Page 9 EJECT CIRCUIT BOARD FOIL SIDE ( B ) COMPONENT SIDE ( A ) EJECT PWB EJECT PWB YB10329-01-02 YB10329-01-02 (Sanwa)-M1D5S8 E. & O. E. No. 86646 GR-DVP3A-SL/A-GY/A-GYC/EA/ED/SH...
  • Page 10 SECTION 5 PARTS LIST SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. PACKING AND ACCESSORY ASSEMBLY <M1> The instruction manual to be provided with this product will differ according to the destination. FINAL ASSY <M2>...
  • Page 11 REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ****************************** PACKING AND ACCESSORY ASSEMBLY <M1>...
  • Page 12 FINAL ASSEMBLY <M2> 193A 193D 193C 193B EJECT <06> OPTICAL BLOCK SECTION 251D 251C 251D 251J 251J 251H 254A 251E 251G <05> 251F BOTTOM <03> 251A 251B 251C 251C 251C 251C...
  • Page 13 ELECTRONIC VIEWFINDER <M4> AUDIO MECHANISM <02> <M3> 198 198 198 165A MAIN <01> 165A 168A 207A 207B 165A 207C 130A 130B RATING LABEL 130C 141A MONITOR <M5> 125A TTOM <03> 135A...
  • Page 14 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 15 SERVICE MANUAL DIGITAL VIDEO CAMERA GR-DVP1EG/EK,DVP3EG/EK SPECIFICATIONS For Connectors Camcorder For General : 1 V (p-p), 75 Ω, analogue Video output Audio output : 300 mV (rms), 1 kΩ, analogue, stereo Power supply : DC 6.3 V } (Using AC Power Adapter/Charger) DC 7.2 V } (Using battery pack) Input/output (GR-DVP3 only) : 4-pin, IEEE 1394 compliant...
  • Page 16: Table Of Contents

    6.3 CIRCUIT BOARD ................. 6-4 3.2 SETUP ..................3-2 6.4 ELECTRICAL PARTS LIST ............6-5 MAIN & TERMINAL BOARD ASSEMBLY <91> ....... 6-5 The following table lists the differing points between Models GR-DVP1EG/EK and GR-DVP3EG/EK in this series. GR-DVP1EG GR-DVP1EK GR-DVP3EG...
  • Page 17: Important Safety Precautions

    Important Safety Precautions Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 18 • Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
  • Page 19: Disassembly

    SECTION 1 DISASSEMBLY 1.1 BEFORE ASSEMBLY AND DISASSEMBLY 1.1.4 Disconnection of Connectors (Wires) 1.1.1 Precautions Connector Pull both ends of the connector in the arrow direction, re- 1. Be sure to remove the power supply unit prior to mount- move the lock and disconnect the flat wire. ing and soldering of parts.
  • Page 20: Jigs And Tools Required For Disassembly, Assembly And Adjustment

    1.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, 1.3 DISASSEMBLY/ASSEMBLY OF CABINET PARTS ASSEMBLY AND ADJUSTMENT AND BOARD ASSEMBLY 1.2.1 Tools required for adjustments 1.3.1 Disassembly flow chart This flowchart indicates the disassembly step for the cabi- Torque Driver YTU94088 YTU94088-003 net parts and board assembly in order to gain access to item(s) to be serviced.
  • Page 21: Disassembly Method

    1.3.2 Disassembly method NOTE a: If a card is installed, remove it in advance. STEP Fig.No. PART POINT NOTE NOTE b: Be careful not to damage the battery removal switch. COVER (UNDER) Fig.1-3-1 (S1) — When disassembling, ensure that the lock lever is in the COVER (SHOE) Fig.1-3-2 2(S2), (L2a), (L2b) —...
  • Page 22 Fig. 1-3-2 Fig. 1-3-1 NOTE NOTE BATT. RELEASE SWITCH COVER (SD) SD CARD LOCK LEVER COVER (JIG) Fig. 1-3-3a...
  • Page 23 NOTE · · : 0.118N m (1.2kgf Fig. 1-3-3b GUIDE (MONI) NOTE NOTE · · : 0.98N m (1.0kgf Fig. 1-3-4 Fig. 1-3-5...
  • Page 24 NOTE CASS. COVER SPACER SHEET (SHUTTER) Fig. 1-3-6 BRACKET(MECHA) ASSY SHEET (SHUTTER) SHIELD ASSY BRACKET (PRE/REC) Fig. 1-3-7...
  • Page 25 NOTE NOTE AUDIO NOTE SPACER SPACER NOTE HOOD Fig. 1-3-8a NOTE NOTE NOTE KNOB (VIDEO /DSC) SPACER SPACER NOTE Fig. 1-3-8b...
  • Page 26: Disassembly Of 5 Monitor Assembly

    1.4 DISASSEMBLY OF 5 MONITOR ASSEMBLY 1.4.2 Hinge assembly 1. Remove the two screws (4,5) to take out the FPC assem- 1.4.1 5 Monitor assembly/Hinge assembly bly while removing the hinge cover. 1. Remove the three screws (1 to 3) and then remove the Note d: Be careful not to lose any part during the above- monitor cover by disengaging the two hooks (L5a, L5b)
  • Page 27: E. Vf Assembly

    1.5 DISASSEMBLY OF E. VF ASSEMBLY 1.5.1 E. VF assembly Note a: When disassembling the E. VF assembly, remove <Frame (VF)> the frame (VF) from the case/cap assembly de- 6. Remove the screw (6) first and then LCD module/holder pending on the situation. (LCD).
  • Page 28: Disassembly Of # Op Block Assembly/Ccd Board Assembly

    1.6 DISASSEMBLY OF # OP BLOCK ASSEMBLY/CCD 1.6.3 How to install # OP block assembly and CCD BOARD ASSEMBLY board assembly 1. Install the optical LPF with the # OP block assembly. 1.6.1 Precautions 2. With the spacer rubber left attached to the CCD base 1.
  • Page 29: Emergency Display

    1.7 EMERGENCY DISPLAY Whenever some abnormal signal is input to the syscon CPU, Example (in case of the error number E01): an error number (E01, as an example) is displayed on the LCD monitor or (in the electronic view finder). In every error status, such the message as shown below alternately appear over and over.
  • Page 30: Service Know-How

    1.8 SERVICE KNOW-HOW 1. See Fig. 1-8-1. When performing disassembly/assembly work to this model, the parts that are most complicated and require special at- (1) Remove the hood by moving the 0 microphone out of tention are the E. VF unit and the AUDIO board, OP block way.
  • Page 31 2. See Fig. 1-8-2. (1) Remove the two screws (35,36) in order to free the @ AUDIO board assembly. (2) Remove the three screws (37 to 39), peel off the spacer and take out the @ AUDIO board assembly together with the # OP block assembly and the $ shoe assembly.
  • Page 32: Service Note

    1.9 SERVICE NOTE 1-14...
  • Page 33: Mechanism Adjustment

    SECTION 2 MECHANISM ADJUSTMENT 2.1 PRELIMINARY REMARKS ON ADJUSTMENT AND (5) This column indicates parts and points such as screws, REPAIR washers,springs,and others to be removed/fitted for dis- assembling/reassembling the mechanism. Besides such 2.1.1 Precautions the parts, this column occasionally indicates working 1.
  • Page 34: Jigs And Tools Required For Disassembly, Assembly And Adjustment

    2.2 JIGS AND TOOLS REQUIRED FOR DISASSEMBLY, ASSEMBLY AND ADJUSTMENT 2.2.1 Tools required for adjustments 1. Torque Driver Torque Driver YTU94088 YTU94088-003 Be sure to use to fastening the mechanism and exterior parts because those parts must strictly be controlled for tightening torque.
  • Page 35: Disassembly/Assembly Of Mechanism Assembly

    2.3 DISASSEMBLY/ASSEMBLY OF MECHANISM AS- 2.3.2 Explanation of mechanism mode SEMBLY The mechanism mode of this model is classified into five 2.3.1 General statement modes as shown in Table 2-3-1. Each mechanism mode can be distinguished from others by the relative position The mechanism should generally be disassembled/assem- of “...
  • Page 36: Mechanism Timing Chart

    2.3.3 Mechanism timing chart MODE SHORT TU. P. B SLIDE TU. P. B SLIDE RELEASE EJECT CAS. IN START START STOP PLAY PARTS MAIN CAM -12.40° 0° (22.44°) 58.71° (69.53°) (80.5°) (150.58°) (153.5°) 177.79° 212.77° 243.94° SUB CAM -16.97° 0° (30.71°) 80.34°...
  • Page 37: Disassembling Procedure Table

    2.4 DISASSEMBLING PROCEDURE TABLE MARK: After assembly, perform adjustments. PART NAME FIG. POINT NOTE REMARKS CASSETTE HOUSING ASSY Fig.2-4-3 ),(L a)-(L NOTE a,b,c,d ADJUSTMENT UPPER BASE ASSY Fig.2-4-4 ),(L a),(L NOTE DRUM ASSY a),2(S NOTE REEL DISK ASSY(SUP) Fig.2-4-5 NOTE REEL DISK ASSY(TU) NOTE REEL COVER ASSY...
  • Page 38 < TOP VIEW > 24 27 36 35 Fig. 2-4-1 < BOTTOM VIEW > 31 16 Fig. 2-4-2...
  • Page 39: Disassembly/Assembly

    2.4.1 Disassembly/assembly CASSETTE HOUSING ASSY NOTE NOTE Be careful not to damage any of the parts during work. NOTE NOTE NOTE Special care is required in mounting. NOTE NOTE LOCK When mounting, the CASSETTE NOTE LEVER HOUSING ASSY should be at- NOTE tached in the Eject status.
  • Page 40 REEL DISK ASSY(SUP) REEL DISK ASSY(TU) REEL COVER ASSY NOTE NOTE Be careful not to attach the REEL DISK wrongly. The Sup- NOTE ply side can be identified by the white color at the center. NOTE NOTE REEL DISK ASSY Be careful not to attach the REEL DISK wrongly.
  • Page 41 SLIDE DECK ASSY NOTE Each of the parts on the SLIDE DECK ASSY can be re- placed separately. When detaching the assembly, if there is no need to replace any of its parts, remove the SLIDE DECK ASSY as it is. NOTE When mounting, pay attention to the positions of the ¤...
  • Page 42 TENSION CTL LEVER ASSY CENTER GEAR & PINCH ROLLER ARM F. ASSY TENSION CTL PLATE ASSY BRAKE CTL LEVER ASSY NOTE NOTES When mounting, pay attention to the correct positioning. NOTE NOTE NOTE (TOP) NOTE (BOTTOM) NOTE NOTES When mounting, pay atten- &...
  • Page 43 fl BASE R ASSY ‡ ROTARY ENCODER ° GEAR COVER ASSY · MAIN CAM ASSY NOTE fl NOTE NOTE When mounting, fold the sliding part to the inner side. ‡ NOTE NOTE When mounting, pay attention to the correct positioning and the FPC layout.
  • Page 44 ∞ DRUM BASE ASSY § CAPSTAN MOTOR ¶ MAIN DECK ASSY ∞ § NOTES When detaching, remove them together and then separate § from ∞ a. ∞ NOTE When mounting, attach the DRUM BASE ASSY so that the screw hole is located at the center of the ellipse. NOTE NOTE NOTE...
  • Page 45: List Of Procedures For Disassembly

    2.4.2 List of procedures for disassembly Fig. 2-4-13 2-13...
  • Page 46: Checkup And Adjustment Of Mechanism Phase

    2.5 CHECKUP AND ADJUSTMENT OF MECHANISM PHASE MODE GEAR ROTARY ENCODER Align the MODE GEAR with the Main Deck Mount the ROTARY ENCODER by aligning its mark ( Assembly hole. and the mark ( ) of the Main Deck Assembly. Note: Note: Be careful when handling the FPC during mounting.
  • Page 47: Mechanism Adjustments

    2.6 MECHANISM ADJUSTMENTS 2.6.1 Adjustment of the slide guide plate Use Fig. 2-6-1 as the reference unless otherwise specified. 1. Set the PLAY mode. See Fig. 2-3-8. 2. Loosen the screws ( A , B ). 3. With the Main Deck and Slide Deck Assemblies pushed into the unit, tighten the screws ( A , B ) while applying pressure to the stud (shaft) on the Slide Guide plate.
  • Page 48: Adjustment Of The Tension Arm And Pad Arm Assemblies

    2.6.2 Adjustment of the Tension Arm and Pad Arm As- semblies Use Fig. 2-6-2 as the reference unless otherwise specified. TENSIOM ARM ASSY 1. Set the PLAY mode. Se Fig. 2-3-8. SCREW B 2. Loosen the screw A . 3. With the take-up side at the bottom, align the extreme end of the Tension Arm Assembly with the crossed grooves on the screw B that retains the Loading Motor Assembly and then tighten the screw A .
  • Page 49: Jig Connector Cable Connection

    2.7 JIG CONNECTOR CABLE CONNECTION Remove one screw (1) first and the cover (JIG) next. GUIDE ROLLER GUIDE ROLLER (TU) ASSY (SUP) ASSY COVER (M.ADJ) COVER (JIG) JIG CONNECTOR CABLE Fig. 2-7-1 MAIN JIG CONN. BOARD CN114 (PIN NO.) VF_RPD VF_RPD CVF_G CVF_R...
  • Page 50: Service Note

    2.8 SERVICE NOTE Use the following chart to manage mechanism parts that are removed for disassembling the mechanism. Fig. Fig. CASSETTE HOUSING ASSY UPPER BASE ASSY Fig. Fig. REEL DISK ASSY(SUP) REEL COVER ASSY DRUM ASSY REEL DISK ASSY(TU) Fig. TENSION ARM ASSY SLANT POLE ARM ASSY TU ARM ASSY...
  • Page 51 Fig. PINCH ROLLER TENSION BRAKE CTL TENSION CTL CENTER GEAR ARM F. ASSY CTL PLATE LEVER LEVER ASSY ASSY ASSY Fig. MOTOR GUIDE SLIDE LEVER 2 LOADING BRACKET RAIL ASSY ASSY PLATE ASSY ASSY MODE GEAR EJECT LEVER Fig. BASE R ASSY ROTARY GEAR COVER MAIN CAM ASSY...
  • Page 52: Electrical Adjustment

    SECTION 3 ELECTRICAL ADJUSTMENT 3.1 PRECAUTION 1. Precaution Both the camera and deck sections of this model needs a personal computer for adjustment except simple adjustment Jig Connector Cable Communication Cable with potentiometers. If some of the following parts is replaced YTU93106C YTU93107A for repair or other reason, the repaired set must be adjusted...
  • Page 53: Setup

    Torque driver Service support system Be sure to use to fastening the mechanism and exte- To be used for adjustment with a personal computer. rior parts because those parts must strictly be control- 10. INF adjustment lens led for tightening torque. To be used for adjustment of the camera system.
  • Page 54: Charts And Diagrams

    SECTION 4 CIRCUIT BOARD NOTES CHARTS AND DIAGRAMS 1. Foil and Component sides 1) Foil side (B side) : NOTES OF SCHEMATIC DIAGRAM 4. Voltage measurement Parts on the foil side seen from foil face (pattern face) are indicated. 1) Regulator (DC/DC CONV) circuits Safety precautions REC : Colour bar signal.
  • Page 55: Board Interconnections

    BOARD INTERCONNECTIONS YTU94074-16 YTU94074-24 YTU94077-16 NOTE ) YTU94077-24 : The number of patch cords are indicated by interconnected. SHOE ASSY LCD MODULE WBSE/SW CN201 (Page 4-37) (Page 4-36) YTU94074-20 YTU94074-20 YTU94077-20 CN201 YTU94077-20 CN201 REG 4.8 YTU94074-13 UN REG MAIN AUDIO (Page 4-43) AUDIO AD/DA YTU94077-13...
  • Page 56: Syscon-Cpu Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from SYSCON-CPU SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( SYSCON-CPU ) TO MSD-CPU TO MSD-CPU,...
  • Page 57: Msd-Cpu Schematic Diagram

    MSD-CPU SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. NQR0006-001X TO REG MAIN ( MSD-CPU )
  • Page 58: Mda Schematic Diagram

    MDA SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( MDA ) MSD-CPU CAPSTAN MOTOR...
  • Page 59: Dv Main Schematic Diagram

    DV MAIN SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( DV MAIN ) TO DSC REG CON...
  • Page 60: Pre/Rec Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from PRE/REC SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO MSD-CPU TO REG CON CAM.
  • Page 61: Video Out Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from VIDEO OUT SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO REG TO REG CON TO REG CON...
  • Page 62: Cam. Dsp Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from CAM. DSP SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. ( CAM.
  • Page 63: Tg/Vdr Schematic Diagram

    TG/VDR SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( TG/VDR ) TO CCD CN5001...
  • Page 64: Vf Main Schematic Diagram

    4.10 VF MAIN SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( VF MAIN ) TO REG MONITOR MAIN...
  • Page 65: Reg Con Schematic Diagram

    4.11 REG CON SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO WBSE/SW CN201 TO SYSCON-CPU TO SYSCON-CPU...
  • Page 66: Reg Schematic Diagram

    4.12 REG SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO SYSCON-CPU REG CON TO MSD-CPU...
  • Page 67: Monitor Main Schematic Diagram

    4.13 MONITOR MAIN SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO MONITOR REG CON CN401...
  • Page 68: Dsc Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from 4.14 DSC SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( DSC ) USBDRV AUDIO MP3...
  • Page 69: Audio Mp3 Schematic Diagram

    4.15 AUDIO MP3 SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( AUDIO MP3 ) TO REG CON REG CON...
  • Page 70: Usbdrv Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from 4.16 USBDRV SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MAIN ( USBDRV ) TO DSC TO REG...
  • Page 71: W/B Schematic Diagram

    4.17 W/B SCHEMATIC DIAGRAM 4.18 CCD SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. IC5001 is incorporated in the CCD base assembly.
  • Page 72: Wbse/Sw Schematic Diagram

    4.19 WBSE/SW SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from TO REG CON this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. CN110 TO AUDIO AD/DA TO MAIN AUDIO...
  • Page 73: Audio Ad/Da Schematic Diagram

    4.20 AUDIO AD/DA SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. AUDIO ( AUDIO AD/DA ) MAIN AUDIO TO WBSE/SW...
  • Page 74: Main Audio Schematic Diagram

    4.21 MAIN AUDIO SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. TO WBSE/SW UN REG UN REG...
  • Page 75: Opdrv Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from 4.22 OPDRV SCHEMAITC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. AUDIO ( OPDRV ) TO WBSE/SW OP BLOCK...
  • Page 76: Bottom Schematic Diagram

    4.23 BOTTOM SCHEMATIC DIAGRAM NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". TO REG CON When ordering parts , be sure to order according to the Part Number indicated in the Parts List. CN107 CN301 TO J301...
  • Page 77: Monitor Schematic Diagram

    NOTES : For the destination of each signal and further line connections that are cut off from 4.24 MONITOR SCHEMATIC DIAGRAM this diagram , refer to "4.1 BOARD INTERCONNECTIONS". When ordering parts , be sure to order according to the Part Number indicated in the Parts List. MONITOR MAIN MONITOR CN113...
  • Page 78: Ope.cover Unit And Sub Ope. Unit Schematic Diagrams

    4.25 OPE. COVER UNIT AND SUB OPE. UNIT SCHEMATIC DIAGRAMS NOTES : For the destination of each signal and further line connections that are cut off from this diagram , refer to "4.1 BOARD INTERCONNECTIONS". The schematic diagram is only for reference. Avoid replacing individual parts. Replace the entire unit only.
  • Page 79: Main Circuit Board

    4.26 MAIN CIRCUIT BOARD FOIL SIDE ( B ) MAIN PWB YB10327-01-02 CN104 CN105 4-51 4-52...
  • Page 80 COMPONENT PARTS LOCATION GUIDE MAIN/ YB10327-01-02 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C3020 C4202 C6001 C7432 C8114 IC3004 L6106 C3021 C4203 C6002 C7433 C8115 IC3005 L6107 C1004 C3022 C4204 C6003 C7434 C8116...
  • Page 81 COMPONENT PARTS LOCATION GUIDE MAIN/ YB10327-01-02 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION R1018 R1635 R3501 R5510 R7426 R8037 RA8402 TL8008 R1020 R1636 R3502 R5511 R7433 R8038 RA8403 TL8011 R1021 R1637 R3503 R5512 R7436...
  • Page 82 COMPONENT SIDE ( A ) MAIN PWB YB10327-01-02 CN101 CN109 CN103 S1001 CN106 CN112 CN113 4-55 4-56...
  • Page 83: Audio Circuit Board

    4.27 AUDIO CIRCUIT BOARD COMPONENT PARTS LOCATION GUIDE FOIL SIDE ( B ) COMPONENT SIDE ( A ) AUDIO/ YB10328-01-01 REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION REF.NO. LOCATION CAPACITOR C2901 Q2602 R2612 C2904 Q2603 R2613 C1151 C4803 Q2604 R2614 C1152 C4804 Q2901 R2615...
  • Page 84: Bottom Circuit Board

    4.28 BOTTOM CIRCUIT BOARD FOIL SIDE ( B ) COMPONENT SIDE ( A ) BOTTOM PWB BOTTOM PWB YB10329-01-01 YB10329-01-01 4-59 4-60...
  • Page 85: Monitor Circuit Board

    4.29 MONITOR CIRCUIT BOARD 4.30 CCD AND EJECT CIRCUIT BOARDS FOIL SIDE ( B ) FOIL SIDE ( B ) MONITOR PWB YB20907-01-01 CCD PWB YB20906-01-01 COMPONENT SIDE ( A ) COMPONENT SIDE ( A ) MONITOR PWB CCD PWB YB20907-01-01 YB20906-01-01 EJECT...
  • Page 86: Voltage Charts

    4.31 VOLTAGE CHARTS <REG CON> <REG> MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. IC6001 IC6101 Q6103 IC6002 Q6104 -15.5 -16.2 -6.6 -7.0 Q2151 IC6003 -15.0 -15.8 1(E) Q6105 2(B) 1(E)
  • Page 87 <MONITOR> MODE MODE MODE MODE MODE MODE PLAY PLAY PLAY PLAY PLAY PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. PIN NO. Q2901 Q7101 1(E) 2(B) 3(C) Q2902 4(E) 5(B) 6(C) Q7102 -15.0 -14.4 Q7103 1(E) -15.0 2(B) -15.0 <OPDRV>...
  • Page 88: Power System Block Diagram

    4.32 POWER SYSTEM BLOCK DIAGRAM TG/VDR MAIN OP BLOCK CN111 CN5001 REG 12V CCD-6.5V CCD-6.5V REG-6.5V IC5501 REG 3V CCD 12V CCD 12V CCD 12V CCD 12V BATT. TERMINAL F6101 SP UNREG Q5001 F6102 M UNREG DRUM PWR CAP PWR AUDIO UNREG PWR CTL...
  • Page 89: Video System Block Diagram

    4.33 VIDEO SYSTEM BLOCK DIAGRAM MAIN FMC(0 3), FMY(0 7) IC4302 IC4303 TMC(0 3), TMY(0 7) (MEMORY) TPA +/-, TPB +/- J101 DV JACK IC4201 CCD OUT ADIN(0 9) OP BLOCK (CDS/AGC/AD) DYO(0 DYO(0 DCO(0 3) DCO(0 3) REC DATA DATA OUT IC4301 IC3001...
  • Page 90: Parts List

    INST.BOOK(DA),A,C HU ..HUNGARIAN LYT0796-008A INST.BOOK(FI),A,C LYT0796-009A INST.BOOK(SW),A,C MODEL MARK LYT0796-010A INST.BOOK(NO),A,C GR-DVP1EG LYT0796-011A INST.BOOK(RU),A,C GR-DVP1EK LYT0796-012A INST.BOOK(CZ),A,C LYT0796-013A INST.BOOK(PO),A,C GR-DVP3EG LYT0796-014A INST.BOOK(HU),A,C GR-DVP3EK ! 27 LYT0760-001A INST.BOOK(SOFT.5LANG),A LYT0760-001B INST.BOOK(SOFT.5LANG),C LYT0760-002B INST.BOOK(SOFT.5LANG),A,C LYT0760-003B INST.BOOK(SOFT.RU),A,C LYT0761-001A INST.BOOK(SOFT.EN),B,D LYT0378-003A SHEET(AGREMENT) LYT0760-004A SHEET(ATT.)
  • Page 91 FINAL ASSEMBLY <M2> ELECTRONIC VIEWFINDER <M4> 193A AUDIO 193D MECHANISM 193C <02> <M3> 198 198 198 193B 165A MAIN <01> 165A 168A 207A 207B 165A 207C 130A 130B RATING LABEL 130C EJECT <06> OPTICAL BLOCK 251D SECTION 251C 251D 251J 141A 251J MONITOR...
  • Page 92: Final Assembly

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 93 MECHANISM ASSEMBLY <M3> 436B 436B 436A Classification Part No. Symbol in drawing Grease KYODO-SH-P NOTE:The section marked in AA and BB, CC indicate YTU94027 lubrication and greasing areas. Grease RX-410R (HANARL)
  • Page 94: Mechanism Assembly

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 95: Electronic Viewfinder Assembly

    ELECTRONIC VIEWFINDER ASSEMBLY <M4> REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 96: Monitor Assembly

    MONITOR ASSEMBLY <M5> 501A 501C 501B MONITOR <04> REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 97: Electrical Parts List

    ELECTRICAL PARTS LIST REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 98 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 99 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 100 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 101 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 102 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 103 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 104 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 105: Audio Board Assembly <02

    REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 106 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 107 REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 108: Bottom Board Assembly <03

    SECTION 6 AC POWER ADAPTER (AA-V100EG/EK) REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
  • Page 109: Schematic Diagram

    Safety precautions SCHEMATIC DIAGRAM The components identified by the symbol ! are critical for NOTE: when ordering parts, be sure to order according to safety. For continued safety, replace safety critical components the Part Number indicated in the Parts List. only with manufacturer's recommended parts.
  • Page 110: Circuit Board

    CIRCUIT BOARD...
  • Page 111: Electrical Parts List

    ELECTRICAL PARTS LIST REF No. PART No. PART NAME, DESCRIPTION REF No. PART No. PART NAME, DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -...

Table of Contents