Download Print this page

Cisco 700 Series Quick Start Manual

700 series router cabling and setup.
Hide thumbs
   

Advertisement

Cisco 700 Series Router Cabling and Setup

Quick Start Guide

This document describes the basic process of cabling and configuring the Internet access device, the
Cisco 700 series router. For advanced cabling information, refer to the Cisco 700 Series Router
Installation Guide. For advanced configuration information, refer to the Cisco 700 Series Router
Command Reference and the Cisco 700 Series Router Software Configuration Guide. These documents can
be found on the Cisco Documentation CD-ROM and Cisco Connection Online (CCO).

Parts List

One Cisco 700 series router
One yellow Ethernet cable
One red ISDN U cable (Cisco 776 routers only)
One orange ISDN S/T cable (Cisco 761 and 775 routers only)
One RJ-45-to-RJ-11 adapter
One blue config cable
One black power supply
One black power supply cord
One Cisco Fast Step CD-ROM
Additional parts might be required to install Cisco775 and Cisco 776 routers. An Ethernet
Note
crossover cable must be used to connect a hub to the router. Depending on the country, you
might need a phone port adapter to connect an analog telephone. These parts must be
provided by the user.
Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 1999. Cisco Systems, Inc. All rights reserved.

Advertisement

   Related Manuals for Cisco 700 Series

   Summary of Contents for Cisco 700 Series

  • Page 1: Quick Start Guide

    This document describes the basic process of cabling and configuring the Internet access device, the Cisco 700 series router. For advanced cabling information, refer to the Cisco 700 Series Router Installation Guide. For advanced configuration information, refer to the Cisco 700 Series Router Command Reference and the Cisco 700 Series Router Software Configuration Guide.

  • Page 2

    Verify the PC Setup Before you begin, verify that each computer that will be connected to the computer has a network interface card (NIC) installed and TCP/IP loaded. Connect a 760 Series Router to a PC or Hub If you are connecting the router to a computer, connect the yellow Ethernet cable from the yellow Step 1 Ethernet port on the rear panel of the router to the Ethernet port on the network interface card on the computer.

  • Page 3

    Connect a 770 Series Router to a PC or Hub Step 1 If you are connecting to a computer, connect a yellow Ethernet cable from a yellow Ethernet port on the rear panel of the router to the Ethernet port on the network interface card on the computer. If you are connecting the router to a hub, omit this step.

  • Page 4

    Step 1 Outside North America, connect the orange ISDN S/T cable to the orange ISDN S/T port on the rear panel of your router. Inside North America, see the Cisco 700 Series Router Installation Guide for instructions. CO NFI G...

  • Page 5: Connect The Power And Turn On The Router

    LED on the Cisco 772 and Cisco 776) on the front panel of your router turns on. Your router is now ready to be set up. If the green RDY LED is not on, refer to the “Troubleshooting Cisco 700 Series Routers” chapter in the Cisco 700 Series Router Installation Guide.

  • Page 6

    Setup the Router to Access a Corporate Network or Internet Service Provider A Cisco Fast Step CD-ROM and a RVS-COM Lite CD-ROM is included with your router. We recommend that you use Cisco Fast Step software to set up the router and RVS-COM Lite software for Common ISDN Application Programmers Interface (CAPI) support.

  • Page 7

    78-10157-01...

  • Page 8

    LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners.

This manual also for:

761, 775, 762, 776

Comments to this Manuals

Symbols: 0
Latest comments: