Advertisement
Quick Links
HTHBHACG8BL*1B
HTHBHACG8BLNF*1B
Owners Manual
MANUAL DEL PROPIETARIO HALSEY TAYLOR
MANUEL DE L'UTILISATION HALSEY TAYLOR
Hydroboost Bottle Filling Station and Cooler
Estación de llenado de botella Hydroboost y enfriador
Station de remplissage de bouteille Hydroboost et refroidisseur
Page 1
1000001716 (Rev. M - 01/19)
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Halsey Taylor HydroBoost HTHBHACG8BL 1B Series
Summary of Contents for Halsey Taylor HydroBoost HTHBHACG8BL 1B Series
- Page 1 HTHBHACG8BL*1B HTHBHACG8BLNF*1B Owners Manual MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L'UTILISATION HALSEY TAYLOR Hydroboost Bottle Filling Station and Cooler Estación de llenado de botella Hydroboost y enfriador Station de remplissage de bouteille Hydroboost et refroidisseur Page 1 1000001716 (Rev. M - 01/19)
- Page 2 HTHBHACG8BL*1B HTHBHACG8BLNF*1B Note: Danger! Electric shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad. Remarque : Danger ! Risque d'électrocution. Débrancher avant de réparer l'appareil. Pictured is unit only without bottle filler. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A...
- Page 3 HTHBHACG8BL*1B HTHBHACG8BLNF*1B STANDARD TWO-LEVEL INSTALLATION Fig. 2 Page 3 1000001716 (Rev. M - 01/19)
- Page 4 HTHBHACG8BL*1B HTHBHACG8BLNF*1B IMPORTANT IMPORTANTE MPORTANT ALL SERVICE TO BE PERFORMED BY AN TODO EL SERVICIO DEBERÁ SER EFECTUADO POR TOUT ENTRETIEN DOIT ÊTRE EFFECTUÉ PAR AUTHORIZED SERVICE PERSON UNA PERSONA DE SERVICIO AUTORIZADA UN REPRÉSENTANT AUTORISÉ HANGER BRACKETS & TRAP INSTALACIÓN DE FIJADOR DE INSTALLATION DU SIPHON ET DU INSTALLATION...
- Page 5 HTHBHACG8BL*1B HTHBHACG8BLNF*1B PUSH BAR MECHANISM MECANISMO DE BARRA DE EMPUJE MÉCANISME DU BOUTON-POUSSOIR 13 B Fig. 6 Water Valve Mechanism - ADJUSTMENT PROCEDURE: LEGEND/LEYENDA/LÉGENDE - Turn adjustment screw “Counter-Clockwise” until water flow A) Note: Water flow direction from bubbler starts. Nota: Dirección del flujo de agua - Turn adjustment screw “Clockwise”...
- Page 6 HTHBHACG8BL*1B HTHBHACG8BLNF*1B MOUNTING 7/16” BOLT HOLES FOR SCREWS FASTENING UNIT TO WALL UNIT CENTER LINE TOP COVER Fig. 8 Fig. 9 Fig. 10 Fig. 9 BRACKET & SCREWS Fig. 11 Fig. 10 Bottle Filler Installation Instructions 1) Remove two (2) mounting screws with 5/32” Allen wrench holding top cover to Bottle Filler (See Fig. 9). Remove top cover. Note do not discard mounting screws, they will be needed to reinstall top cover.
- Page 7 HTHBHACG8BL*1B HTHBHACG8BLNF*1B BF11 - BF12 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 2) When the display changes to “SETTINGS”, depress the button again. need to be shut down and restarted.
-
Page 8: Wall Mounting Plate
HTHBHACG8BL*1B HTHBHACG8BLNF*1B BOTTLE FILLING UNIT WALL MOUNTING PLATE Fig. 12 Fig. 13 Superseal Fitting Assembly Supersello Accesorio de Montaje Superseal Montage Assemblage Note: Screw the locknut hand tight to seal. Nota: Apriete la mano de la contratuerca para sellar. Remarque : Visser la main de l'écrou de blocage pour assurer l'étanchéité. Fig. - Page 9 HTHBHACG8BL*1B HTHBHACG8BLNF*1B PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM PART NO DESCRIPTION DESCRIPCIÓN DESCRIPTION 22897C Panel - Bottom Dispenser Panel - Dispensador Inferior Panneau - Distributeur Inférieur 23003C Bracket - Regulator Mounting Fijador - Montaje Regulador Support de Guidon-Kit 28551C Hanger Bracket Fijador de Suspensión...
Need help?
Do you have a question about the HydroBoost HTHBHACG8BL 1B Series and is the answer not in the manual?
Questions and answers