Related Manuals for Elo TouchSystems E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4
Summary of Contents for Elo TouchSystems E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4
- Page 1 ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4 E797162 ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE © Copyright 2021 Elo Touch Solutions, Inc. QIG600185 Revision B...
- Page 2 Contents for Kit: E421325 ELO-STAND-SELF-SERVICE-15-22-FLOOR-TOP4 Hardware SCREW, M4X8, PAN-HEAD, Qty.10 CROSS-RECESS SCREW, M4X8, FLAT-HEAD, Qty.4 CROSS-RECESS SCREW, M3X8, PAN-HEAD, Straps Qty.3 CROSS-RECESS Qty. 3 SCREW, 3mm X8L, Qty.4 THREAD-FORMING, PAN-HEAD SCREW, M5X10, FLAT-HEAD, Qty.6 CROSS-RECESS Display Bracket, Android Qty. 1 SCREW, M4X6, PAN-HEAD, Qty.4...
- Page 3 Contents for Kit: E797162 ELO-STAND-SELF-SERVICE-15-22-FLOOR-BASE Floor Base Qty. 1 © Copyright 2021 Elo Touch Solutions, Inc.
- Page 4 Assemble tower to base plate using (4) screws from bag “K”. • Remove and save the (4) screws on the left and right of the stand front cover. • Pull off the silver cover and set aside. • Add (2) remaining screws from bag “K” to bottom front of stand. ©...
- Page 5 Remove and save (2) screws on rear of Head, pull out printer tray. © Copyright 2021 Elo Touch Solutions, Inc.
- Page 6 (Power strip shown available from McMaster-Carr, item Add power bricks into tower using provided straps. #7361K43) • Add power strip brackets (supplied with power strip) using (2) screws from bag “L”. • Hook one side of power strip onto brackets then push to snap down. ©...
- Page 7 Choose Android or Windows Display Bracket For 15” or 22” monitor, use Android Display Bracket Android Display Bracket shown above Add (2) screws from bag “A”; leave ~3mm (1/8”) gap Remove and save (2) screws, open cover of Display Bracket; (for Display Bracket).
- Page 8 • Assemble Display Bracket onto Head. • Assemble USB Hub. • Position “A” for 15”, 22” in landscape. • Add (2) screws from bag “S”; leave ~3mm (1/8”) gap for USB bracket to slide on; tighten screws. • Position “B” for 15” in portrait •...
- Page 9 Android Slate: Landscape (For Portrait, skip to step 12) Note: EMV Cradles are not compatible with Android Slate in landscape orientation. Top Landscape Add tie-wrap • Add (2) screws from bag “L” to top 75mm VESA Route Slate Hub through display bracket and head. Mount Slate, add (2) positions.
- Page 10 Android Slate: Portrait If using an EMV Cradle, follow those instructions before proceeding. Top Portrait Add tie-wrap • Route • Add (2) screws from bag “L” to top 75mm VESA Slate Hub through display bracket and head. positions. Leave ~3mm (1/8”) gap for mounting to •...
- Page 11 Apply double-sided foam tape from bag “U” to back of Slate Hub and attach to back of tower approximately where shown. Route LAN cable through tower base. Connect LAN and power supply to Slate Hub. Skip to step © Copyright 2021 Elo Touch Solutions, Inc.
- Page 12 Android or 15”/22” Monitor: Landscape (For Portrait, skip to step 17) If using an EMV Cradle, follow those instructions before proceeding. Note: EMV Cradles are not compatible with monitors in landscape orientation. Top Landscape Add tie-wrap Cable direction • Add (2) screws from bag “L” to top 100mm VESA •...
- Page 13 Android or 15”/22” Monitor: Portrait If using an EMV Cradle, follow those instructions before proceeding. Top Portrait Cable direction Add tie-wrap F o r 2 2 ” M o n ito r, it is re c o m m e n d e d to u s e c e n te rin g p la te Mount i-Series, add (2) screws from bag “L”...
- Page 14 Optional: Mount Backpack 4.0 to tower bracket as shown using (4) screws from bag “T”. To improve Wi-Fi signal use antenna extension cables (Amphenol RF P/N 095-902-538-024, available from Digikey or Mouser). Remove antennas from Backpack, attach (2) extension cables to Backpack antenna connectors.
- Page 15 Windows Landscape (For Portrait, skip to step 24) If using an EMV Cradle, follow those instructions before proceeding. 15” Landscape 22” Landscape 15”: add (2) screws from bag “M” to top 75mm VESA positions. Route power cable from I-Series through bottom of stand, 22”: add (2) screws from bag “N”...
- Page 16 Mount I-Series, then add bottom VESA screws: Add (2) screws from bag “M” (15”) or bag “N” (22”) to bottom 75mm VESA positions. Add tie-wrap Place I-Series on surface near stand head, within reach of Route, LAN cable through bottom of stand head. Route cable.
- Page 17 Windows Portrait If using an EMV Cradle, follow those instructions before proceeding. 15” Portrait 22” Portrait 15”: add (2) screws from bag “M” to top 75mm VESA positions. Route power cable from I-series through bottom of 22”: add (2) screws from bag “N” to top 100mm VESA positions. stand, through openings in the mount bracket as shown.
- Page 18 Mount I-Series, then add bottom VESA screws: 15”: add (2) screws from bag “M” to bottom 75mm VESA positions. 22”: add (2) screws from bag “N” to bottom 100mm VESA positions. Add tie-wrap Route, LAN cable through bottom of stand Place I-Series on surface near stand head, within reach of head.
- Page 19 If no printer, skip to step If using printer, remove cover to add printer. Add (2) screws from bag “C” to printer tray; use Star printer Star Continue to step printers. bracket to set depth of screws than remove Star bracket. Epson TM-T88, skip to step ©...
- Page 20 Add Star printer bracket to printer; refer to Star instructions. Epson TM-T88 Add Star printer with bracket to printer tray. Secure printer to printer tray using third screw from bag “C”. Add (4) screws from bag “D” to attach printer to the tray. Skip to step ©...
- Page 21 • Close Display Bracket and add (2) screws saved from step 7. Route cables from/to printer as needed, slide in printer tray assembly (or printer tray with cover if no printer). • Secure printer assembly with (2) screws saved from step 3. ©...
- Page 22 Replace floor stand cover and secure using (4) screws saved (2) bolt holes available on top of base to secure stand to floor. Feet can from step 2. be adjusted in case of uneven surfaces. © Copyright 2021 Elo Touch Solutions, Inc.
- Page 23 If installing an EMV Cradle with display in landscape orientation, finish by adding (1) screw from bag “S”. • KIT-EMV-ING-IPP320/350/315-4 • KIT-EMV-VF-MX915/M400-ING-ISC250-SQ-4 • KIT-EMV-ING-LANE3000-4 • EMV-SELF-SERV-VF-MX925 • EMV-SELF-SERV-VF-P400 EMV-SELF-SERV-ING-RP757 © Copyright 2021 Elo Touch Solutions, Inc.
- Page 24 Learn more about Elo at EloTouch.com. Americas Europe (EMEA) Asia Pacific Tel +1 408 597 8000 Tel +32 16 930 136 Tel +86 (21) 3329 1385 EloSales.NA@elotouch.com EMEA.sales@elotouch.com EloAsia@elotouch.com The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose.