Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.2 2015.08
Amplifi er section
The following are measured at
AC 120 V – 240 V, 50/60 Hz
Power output (rated)
Left/Right Channel: 120 W + 120 W
(at 2 ohms, 1 kHz, 1% THD)
RMS output power (reference)
Left/Right Channel: 180 W + 180 W
(per channel at 2 ohms, 1 kHz)
Subwoofer: 360 W (at 4 ohms, 100 Hz)
Speaker section
Speaker system
Subwoofer, Sound Pressure Horn
Speaker unit
200 mm, cone type
Rated impedance
4 ohms
Inputs
AUDIO IN/PARTY CHAIN IN L/R
Voltage 2 V, impedance 47 kilohms
OPTICAL IN
Supported audio signal:
2-channel Linear PCM
MIC 1, MIC 2
Sensitivity 1 mV, impedance 10 kilohms
(USB) port
Type A
Outputs
AUDIO OUT/PARTY CHAIN OUT L/R
Voltage 2 V, impedance 1 kilohm
VIDEO OUT
Max. output level 1 Vp-p, unbalanced,
Sync. negative load impedance 75 ohms
USB section
Supported bit rate
WMA:
48 kbps – 192 kbps, VBR, CBR
AAC:
48 kbps – 320 kbps, VBR, CBR
Sampling frequencies
WMA: 44.1 kHz
AAC: 44.1 kHz
Supported USB device
Mass Storage Class
9-890-669-03
Sony Corporation
2015H81-1
©
2015.08
Published by Sony EMCS (Malaysia) PG Tec
CD/DVD Section
SPECIFICATIONS
Maximum current
1 A
Disc/USB section
Supported bit rate
MPEG1 Layer-3:
32 kbps – 320 kbps, VBR
Sampling frequencies
MPEG1 Layer-3:
32 kHz/44.1 kHz/48 kHz
Xvid
Video codec: Xvid
Bit rate: 4.854 Mbps (MAX)
Resolution/Frame rate:
720 × 480, 30 fps
720 × 576, 25 fps
Audio codec: MP3
MPEG4
File format: MP4 File Format
Video codec:
MPEG4 Simple Profile
(AVC is not compatible.)
Bit rate: 4 Mbps
Resolution/Frame rate:
720 × 576, 30 fps
Audio codec: AAC-LC
(HE-AAC is not compatible.)
DRM: Not compatible
Disc player section
System
Compact disc and digital audio and
video system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 μW
* This output is the value
measurement at a distance of
200 mm from the objective lens
surface on the Optical Pick-up
Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Video color system format
NTSC and PAL
HCD-GT3D
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
FM tuner section
System
PLL quartz-locked digital synthesizer
Antenna
FM lead antenna
Tuning range
87.5 MHz – 108.0 MHz (50 kHz step)
BLUETOOTH section
Communication system
BLUETOOTH Standard version 3.0
Output
BLUETOOTH Standard Power
Class 2
Maximum communication range
Line of sight approx. 10 m
1)
Frequency band
2.4 GHz band (2.4000 GHz –
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
2)
Compatible BLUETOOTH profiles
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote
Control Profile)
SPP (Serial Port Profile)
Supported codecs
SBC (Sub Band Codec)
AAC (Advanced Audio Coding)
1)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna's performance, operating system,
software application, etc.
2)
BLUETOOTH standard profiles indicate
the purpose of BLUETOOTH communica-
tion between devices.
General
Power requirements
AC 120 V – 240 V, 50/60 Hz
Power consumption
120 W
Russian Model
E Model
Australian Model
HCD-GPX555
CDM90-DVBU204//M
CMS-S76RFS7G
Power consumption (at the Power Saving
mode)
0.5 W
(When "BT STBY" is set to "OFF")
6 W
(When "BT STBY" is set to "ON")
Dimensions (w/h/d) (Approx.)
DVD Receiver (subwoofer unit):
305 mm × 636 mm × 355 mm
Mass (Approx.)
DVD Receiver (subwoofer unit):
14.5 kg
Design and specifications are subject to
change without notice.
– Continued on next page –
DVD RECEIVER

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-GT3D

  • Page 1 AC 120 V – 240 V, 50/60 Hz Video color system format AAC: 44.1 kHz Power consumption NTSC and PAL Supported USB device 120 W DVD RECEIVER Mass Storage Class 9-890-669-03 Sony Corporation 2015H81-1 © 2015.08 Published by Sony EMCS (Malaysia) PG Tec...
  • Page 2 ® • The BLUETOOTH word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony instruments. Corporation is under license. Other trademarks and trade names are 2. A battery-operated AC milliammeter. The Data Precision 245 those of their respective owners.
  • Page 3: Table Of Contents

    HCD-GT3D TABLE OF CONTENTS SERVICING NOTES ..........6-30. Schematic Diagram - SPLITTER Board - ...... 58 DISASSEMBLY EXPLODED VIEWS 2-1. Disassembly Flow ............7-1. Side Panel Section ............72 2-2. Side (L) Panel, Side (R) Panel ........10 7-2. Top Panel Section ............73 2-3.
  • Page 4: Servicing Notes

    HCD-GT3D Ver. 1.1 SECTION 1 SERVICING NOTES Notes on chip component replacement MODEL IDENTIFICATION • Never reuse a disconnected chip component. – Rear View – • Notice that the minus side of a tantalum capacitor may be MODEL NUMBER LABEL damaged by heat.
  • Page 5 ] button to turn the power on. Bluetooth device. 2. Press [FUNCTION] button and turn the [MULTI CONTROL] For example, select “SONY : MHC-GT3D”. If passkey is knob to select “DVD/CD” function, then press [ENTER] required on the Bluetooth device, enter “0000”.
  • Page 6 HCD-GT3D Ver. 1.2 NOTE OF DISASSEMBLE THE PANEL, SIDE Playing music from a Bluetooth device To disassemble the PANEL, SIDE, hexagon key is required to unscrew the SCREW, TAPPING (HEX) (Type A). For a Bluetooth device 1. Press the [ ] button to turn the power on.
  • Page 7 HCD-GT3D Ver. 1.2 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF Note 1: After the side panel and top panel are removed, this work is done. Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
  • Page 8 HCD-GT3D CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION SMPS Board (Conductor side view) In checking the SMPS board, make 3 capacitors discharge of C914, C1003 and C1006 for eletrical shock prevention. 800 /5 W 800 /5 W C1003 800 /5 W...
  • Page 9: Disassembly

    HCD-GT3D SECTION 2 DISASSEMBLY Note: Disassemble the unit in the order as shown below. 2-1. DISASSEMBLY FLOW 2-2. SIDE (L) PANEL, SIDE (R) PANEL (Page 10) 2-3. TOP PANEL SECTION (Page 11) 2-4. OPTICAL BOARD (Page 12) 2-5. LOADING PANEL ASSY (Page 12) 2-6.
  • Page 10: Side (L) Panel, Side (R) Panel

    HCD-GT3D Ver. 1.2 Note: Follow the disassembly procedure in the numerical order given. 2-2. SIDE (L) PANEL, SIDE (R) PANEL 1 two screws 3 three claws (TAPPING (HEX) (Type A) or TAPPING (Type B)) 2 three screws (+BVTP 3 × 8) 5 panel, side (L) 2 three screws (+BVTP 3 ×...
  • Page 11: Top Panel Section

    HCD-GT3D Ver. 1.2 2-3. TOP PANEL SECTION 3 two screws (+BVTP 3 × 8) 1 three screws (+BVTP 3 × 8) 4 one screw (+BVTP 3 × 8) qs top panel section 8 Remove the wires from pin, lead. 4 one screw (+BVTP 3 × 8)
  • Page 12: Optical Board

    HCD-GT3D Ver. 1.2 2-4. OPTICAL BOARD 1 Remove the wire from pin, lead. 4 one screw (+BVTP 3 × 8) OPTICAL board 5 OPTICAL board pin, lead 2 CN602 (3P) 3 one screw front side (+BVTP 3 × 8) MOTHERBOARD board 2-5.
  • Page 13: Cdm Section

    HCD-GT3D Ver. 1.2 2-6. CDM SECTION 1 two screws (+BVTP 3 × 8) 8 CDM section 7 wire (flat type) (24 core) (CN302) 5 CN401 (6P) 6 wire (flat type) (5 core) (CN303) 3 two claws 4 Remove the CDM section in the direction of the arrow.
  • Page 14: Damp Board

    HCD-GT3D Ver. 1.2 2-8. DAMP BOARD DAMP board 8 heatsink chassis, sub Note: When you install the heatsink, spread the compound rear side referring to “NOTE OF REPLACING THE IC1001 ON THE DAMP BOARD AND THE COMPLETE DAMP BOARD” on servicing notes (page 5).
  • Page 15: Motherboard Board, Splitter Board

    HCD-GT3D Ver. 1.2 2-9. MOTHERBOARD BOARD, SPLITTER BOARD 0 two screws (+BVTP 3 × 8) 5 wire (flat type) (25 core) (CN118) qa SPLITTER board 7 five screws (+BVTP 3 × 8) 8 MOTHERBOARD board 4 wire (flat type) (6 core) (CN105)
  • Page 16: Sub Chassis Section

    HCD-GT3D Ver. 1.2 2-10. SUB CHASSIS SECTION clamp front side fan, DC 2 three screws (+BV3 (3-CR)) bracket, fan 3 clamp 1 Remove the wire from clamp. chassis, sub 4 four screws (+BV3 (3-CR)) 7 sub chassis section 6 Draw out the wires from chassis, sub.
  • Page 17: Smps Board

    HCD-GT3D Ver. 1.2 2-11. SMPS BOARD 2 AC inlet 3 nine screws (+PWH 3 × 8 (SUMITITE)) 1 CN901 (2P) 4 SMPS board 2-12. CHASSIS 2 seven step screws (M4) 3 one claw 5 chassis 3 one claw 4 nine damper chassis 1 one screw (+BVTP 3 ×...
  • Page 18: Front Panel Section

    HCD-GT3D Ver. 1.2 2-13. FRONT PANEL SECTION 1 one screw ((4 × 13) (TR-184A)) 2 Insert the jig into a space and slowly remove the front panel section. Note : When using a jig, please work so as not to injure front panel section and speaker cabinet.
  • Page 19: Loudspeaker (20Cm)-087-11

    HCD-GT3D 2-14. LOUDSPEAKER (20CM)-087-11 terminal position loudspeaker (20cm)-087-11 3 Push the protrusion, and remove the terminal protrusion (wide side) [grey]. terminal (wide side) [grey]. front side front side terminal (narrow side) 3 Push the protrusion, [black/grey]. and remove the terminal (narrow side) [black/grey].
  • Page 20: Service, Optical Device(7G), Wire (Flat Type)

    HCD-GT3D Ver. 1.2 2-15. SERVICE, OPTICAL DEVICE(7G), WIRE (FLAT TYPE) 2 chuck holder assy (T) 1 three claws 1 three claws 7 four insulator screws qa insulator qh holder, FFC qs service, optical device(7G) qa insulator qj wire (flat type) (24 core)
  • Page 21: Test Mode

    3. “COLD RST” appears on the fl uorescent indicator tube. 3. When you want to enter to the software version display mode, After that, the fl uorescent indicator tube will display “SONY press [S2 +] button. DEMO”. The set will automatically Power ON and Power The model information appears on the fl...
  • Page 22 HCD-GT3D [HISTORY MODE] This mode is used to check important data stored in the system when PROTECTOR happened. Procedure: 1. During demo mode, press [ ] button and [S2 +] button for 5 seconds to mode into history mode. 2. Press the [S4 TUNING + >] button or [S3 TUNING – .] button to check history data stored.
  • Page 23 HCD-GT3D Ver. 1.1 [DVD COLOR SYSTEM MODE] 6. To release from this mode, press [\/1] button to turn off the This mode let you change the color system of the video output system. from PAL to NTSC or vice-versa. Procedure: •...
  • Page 24 HCD-GT3D Ver. 1.1 10. Press the [0] button on the remote commander to return to the • Parameter of error code Top Menu of Remocon Diagnosis Menu. This is the detail of error code. 11. Press [\/1] button to turn off the system.
  • Page 25 HCD-GT3D Ver. 1.1 To return to the Top Menu of Remocon Diagnosis Menu Press the [0] button on the remote commander. • Check Version Information To check the version information, please follow the following procedure. 1. From the Top Menu of Remocon Diagnosis Menu, select “4.
  • Page 26: Electrical Check

    HCD-GT3D SECTION 4 ELECTRICAL CHECK 0 dB = 1 μV FOCUS BIAS CHECK TUNER SECTION oscilloscope (DC range) FM AUTO STOP CHECK signal MOTHERBOARD board generator CN302 pin 17 (RF) CN302 pin 1 (GND) – Procedure: 1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302 pin 1 (GND) on the MOTHERBOARD board.
  • Page 27: Troubleshooting

    HCD-GT3D SECTION 5 TROUBLESHOOTING...
  • Page 28 HCD-GT3D...
  • Page 29 HCD-GT3D...
  • Page 30 HCD-GT3D...
  • Page 31 HCD-GT3D Ver. 1.1...
  • Page 32: Diagrams

    HCD-GT3D SECTION 6 DIAGRAMS • Circuit Boards Location DAMP board BUTTON board MIC board OPTICAL board RC-S730 (WW) MS-476 board MOTHERBOARD board SMPS board LCD board BLUETOOTH MODULE SPLITTER board SPK_HLED board...
  • Page 33: Block Diagram - Servo/Usb/Display Section

    HCD-GT3D 6-1. BLOCK DIAGRAM - SERVO/USB/DISPLAY Section - CD RF AMP FOCUS/TRACKING ERROR AMP, CD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR SYSTEM CONTROLLER SERVICE, IC301 SD-RAM IC101 LED DRIVER OPTICAL DEVICE (7G) (1/2) IC306 (1/4) IC502 BLUE HLED 123 RFIP RA0 89...
  • Page 34: Block Diagram - Audio/Video Section

    HCD-GT3D 6-2. BLOCK DIAGRAM - AUDIO/VIDEO Section - MIC AMP J3200 RV3100 IC3200 MIC LEVEL CD RF AMP FOCUS/TRACKING ERROR AMP, CD SYSTEM PROCESSOR, 7 OUT2 +IN2 5 MIC 1 DIGITAL SERVO PROCESSOR IC301 SIGNAL SELECTOR (2/2) 3 +IN1 OUT1 1...
  • Page 35: Block Diagram - Amp Section

    HCD-GT3D 6-3. BLOCK DIAGRAM - AMP Section - POWER AMP IC1001 OUT_A_52 52 4 INPUT_A OUT_A_53 53 PRE AMP L1006 LOUDSPEAKER IC1005 OUT_B_44 44 5 INPUT_B OUT_B_45 45 BIAS +12V Q1022 >001B TB001 AUDIO/VIDEO SECTION OUT_C_36 36 (Page 34) FRONT-L...
  • Page 36: Block Diagram - Power Supply Section

    HCD-GT3D 6-4. BLOCK DIAGRAM - POWER SUPPLY Section - +9V REG +9V REG IC004 IC006 +13V A+13V PWR SUPPLY A+13V_GV2 A+13V_GV2 1 VIN VOUT 3 AVDD+9V 1 VIN VOUT 3 AVDD+5V AVDD+9V, A+9V Q004 +12V REG +3.3V REG IC1003 IC305...
  • Page 37 HCD-GT3D Ver. 1.1 • Note for Printed Wiring Boards and Schematic Diagrams • Waveforms - MOTHERBOARD Board - Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF) •...
  • Page 38 HCD-GT3D IC914 qd (BCK) IC301 8 (XTALO) IC604 3 (LRCK) IC609 7 (LRCK) IC902 qj (X2) IC912 0 (3B) 3.8 Vp-p 3.4 Vp-p 3.4 Vp-p 290 mVp-p 3.4 Vp-p 740 mVp-p 350 ns 85 ns 22 s 22 s 22 s 37.5 ns...
  • Page 39: Printed Wiring Board - Motherboard Board

    HCD-GT3D Ver. 1.1 6-5. PRINTED WIRING BOARD - MOTHERBOARD Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. AUDIO PARTY CHAIN ANTENNA VIDEO MOTHERBOARD BOARD MOTHERBOARD BOARD SERVICE USE (COMPONENT SIDE) (CONDUCTOR SIDE) (CHASSIS)
  • Page 40: Schematic Diagram - Motherboard Board (1/10)

    HCD-GT3D Ver. 1.1 6-6. SCHEMATIC DIAGRAM - MOTHERBOARD Board (1/10) - • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (1/10) >011S MOTHERBOARD BOARD (9/10) (Page 48) /LINE-MUTE R624 2.2k JL635 J602 C1001 C980 C1002 0.001 220p Q602 IMX25T110...
  • Page 41: Schematic Diagram - Motherboard Board (2/10)

    HCD-GT3D Ver. 1.1 6-7. SCHEMATIC DIAGRAM - MOTHERBOARD Board (2/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (2/10) E+3.3V >030S M+13V >013S MOTHERBOARD BOARD MOTHERBOARD (7/10) BOARD (Page 46) (4/10), (7/10) (Page 43), (Page 46) >012S...
  • Page 42: Schematic Diagram - Motherboard Board (3/10)

    HCD-GT3D Ver. 1.1 6-8. SCHEMATIC DIAGRAM - MOTHERBOARD Board (3/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (3/10) AVDD+5V >021S MOTHERBOARD BOARD (2/10), (7/10), (Page 41), (Page 46) DIN1 R719...
  • Page 43: Schematic Diagram - Motherboard Board (4/10)

    HCD-GT3D 6-9. SCHEMATIC DIAGRAM - MOTHERBOARD Board (4/10) - • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (4/10) >011S MOTHERBOARD BOARD (9/10) (Page 48) >003S R791 DIN3 MOTHERBOARD BOARD (1/10) (Page 40) MOTHERBOARD C640 BOARD IC912 (1/10) TC74VHC157FT (EK)
  • Page 44: Schematic Diagram - Motherboard Board (5/10)

    HCD-GT3D Ver. 1.2 6-10. SCHEMATIC DIAGRAM - MOTHERBOARD Board (5/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. • See page 66 for IC Pin Function Descriptions. MOTHERBOARD BOARD (5/10) CVBUS >025S MOTHERBOARD...
  • Page 45: Schematic Diagram - Motherboard Board (6/10)

    HCD-GT3D 6-11. SCHEMATIC DIAGRAM - MOTHERBOARD Board (6/10) - • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (6/10) FE_5V R386 >020S MOTHERBOARD BOARD R500 FE_LD_DVD (2/10) (Page 41) FE_LD_CD R471 CN302 FE_3.3V >028S JL301 GND (LD) FE_VREFO JL302 C366 0.01...
  • Page 46: Schematic Diagram - Motherboard Board (7/10)

    HCD-GT3D 6-12. SCHEMATIC DIAGRAM - MOTHERBOARD Board (7/10) - • See page 37 for Waveforms. MOTHERBOARD BOARD (7/10) L004 2.2uH R087 C039 C014 C021 IC002 TPS542941PWPR IC002 DC-DC CONVERTER 13.7 13.7 C032 VIN2 VIN1 L002 C018 C034 L007 JC005 JC007...
  • Page 47: Schematic Diagram - Motherboard Board (8/10)

    HCD-GT3D Ver. 1.1 6-13. SCHEMATIC DIAGRAM - MOTHERBOARD Board (8/10) - • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (8/10) >011S MOTHERBOARD BOARD (9/10) (Page 48) R125 R131 R123 USBDPVCC >035S MOTHERBOARD R120 BOARD (9/10) (Page 48) R140...
  • Page 48: Schematic Diagram - Motherboard Board (9/10)

    HCD-GT3D Ver. 1.1 6-14. SCHEMATIC DIAGRAM - MOTHERBOARD Board (9/10) - • See page 37 for Waveforms. • See page 59 for IC Block Diagrams. • See page 66 for IC Pin Function Descriptions. MOTHERBOARD BOARD (9/10) MOTHERBOARD BOARD (7/10) (Page 46) >024S...
  • Page 49: Schematic Diagram - Motherboard Board (10/10)

    HCD-GT3D 6-15. SCHEMATIC DIAGRAM - MOTHERBOARD Board (10/10) - • See page 59 for IC Block Diagrams. MOTHERBOARD BOARD (10/10) >011S MOTHERBOARD BOARD (9/10) (Page 48) R543 RGB-PWM-CLK C526 0.01 CN517 C532 47 16V R503 R564 JL518 JL525 M+5.2V /OUT8...
  • Page 50: Printed Wiring Board - Damp Board

    HCD-GT3D Ver. 1.1 6-16. PRINTED WIRING BOARD - DAMP Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. DAMP BOARD (COMPONENT SIDE) MID/TWEETERS IM ED NCE SE 2 LOUDSPEAKER WHITE DAMP BOARD – –...
  • Page 51: Schematic Diagram - Damp Board (1/2)

    HCD-GT3D Ver. 1.1 6-17. SCHEMATIC DIAGRAM - DAMP Board (1/2) - • See page 59 for IC Block Diagrams. DAMP BOARD (1/2) /AMP-RESET CN1005 Q1019 Q1018 PBSS4160T KTA1542T-RTK/P AMP RESET SWITCH 1 V1 AMP RESET SWITCH R1128 4.7k CL1031 3 V1...
  • Page 52: Schematic Diagram - Damp Board (2/2)

    HCD-GT3D 6-18. SCHEMATIC DIAGRAM - DAMP Board (2/2) - >044S DAMP BOARD (1/2) (Page 51) DAMP BOARD (2/2) D1007 RB551V-30TE-17 CN1004 13.7 CL1052 1 FAN+ Q1010 CL1053 DSA700300L 2 FAN- R1062 DC FAN FAN MOTOR 13.7 DRIVER R1139 C1003 R1063...
  • Page 53: Printed Wiring Board - Button Board

    HCD-GT3D 6-19. PRINTED WIRING BOARD - BUTTON Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. S3108 S3107 SOUND FIELD FUNCTION CL3126 R3137 R3136 CL3125 S3123 S3113 MIC BOARD REC TO USB PARTY CHAIN...
  • Page 54: Schematic Diagram - Button Board

    HCD-GT3D Ver. 1.2 6-20. SCHEMATIC DIAGRAM - BUTTON Board - BUTTON BOARD S3114 S3101 CL3132 S3115 CL3119 PARTY LIGHT R3142 S3102 R3130 CN3100 CL3133 D3105 D3100 CL3101 HL-364B460MZ-T HL-364V620MZ-T S3116 LED+5.2V CL3120 BT LED BASS BAZUCA LED FOOTBALL CL3102 R3143 LED+5.2V...
  • Page 55: Printed Wiring Board - Lcd Board

    HCD-GT3D Ver. 1.1 6-21. PRINTED WIRING BOARD - LCD Board - 6-23. PRINTED WIRING BOARD - OPTICAL Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location.
  • Page 56: Printed Wiring Board - Spk_Hled Board

    HCD-GT3D Ver. 1.1 6-25. PRINTED WIRING BOARD - SPK_HLED Board - 6-27. PRINTED WIRING BOARD - MIC Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location.
  • Page 57: Schematic Diagram - Mic Board

    HCD-GT3D Ver. 1.1 6-28. SCHEMATIC DIAGRAM - MIC Board - MIC BOARD R3229 CN3201 CN3202 R3213 CL3204 1 VBUS CL3218 AMP_+IN1 D3200 DZ2J068M0L R3214 D3206 D3205 CL3205 >048S 3 D- CL3219 BAV99-215 BAV99-215 >042S AMP_OUT2 CL3206 BUTTON 4 D+ CL3220...
  • Page 58: Printed Wiring Board - Splitter Board

    HCD-GT3D Ver. 1.1 6-29. PRINTED WIRING BOARD - SPLITTER Board - 6-30. SCHEMATIC DIAGRAM - SPLITTER Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder. SPLITTER BOARD SPLITTER BOARD (COMPONENT SIDE) CN3401 13 LED+5.2V 12 LED+5.2V...
  • Page 59 HCD-GT3D • IC Block Diagrams IC1001 TAS5630BPHDR (DAMP BOARD (1/2)) OC_ADJ 1 VREG CLIP READY OTW1 OTW2 POWER-UP RESET TEMP GVDD_A GVDD_C SENSE GVDD_B GVDD_D /RESET 2 OVER-LOAD CURRENT CB3C PROTECTION SENSE STARTUP CONTROL C_STARTUP 3 PVDD_X PPSC OUT_X GND_X...
  • Page 60 HCD-GT3D IC3004 BU9795AKS2 (LCD BOARD) SEG23 COM2 1 SEG22 COM3 2 LCD voltage generator Segment Common NC 3 driver driver SEG21 VLCD 4 SEG20 VDD 5 LCD BIAS Blink SELECTOR Common timing DDRAM SEG19 VSS 6 counter generator SEG18 OSCIO 7...
  • Page 61 HCD-GT3D Ver. 1.2 IC305 BU33TD3WG-TR (MOTHERBOARD BOARD (5/10)) VDD 1 VREF – 5 VOUT GND 2 Discharge STBY 4 NC CE 3 IC306 EM638165TSD-6G (MOTHERBOARD BOARD (5/10)) VDDQ DQ10 VSSQ DQ11 DQ12 VDDQ DQ13 DQ14 VSSQ DQ15 NC 40 1 VDD...
  • Page 62 HCD-GT3D IC453 TC7USB40FT (MOTHERBOARD BOARD (10/10)) NC 11 7 GND 11 6 D- 11 5 2D- 11 4 1D- 11 3 12 OE S 11 2 NC 11 1 IC502 TC62D723FNG (MOTHERBOARD BOARD (10/10)) 25 GND Error detection result SIN 2...
  • Page 63 HCD-GT3D IC604, IC615 PCM1754DBQR (MOTHERBOARD BOARD (3/10)) SYSTEM SYSTEM 16 SCK CLOCK CLOCK MANAGER AUDIO SERIAL DATA SERIAL CONTROL MUTE PORT PORT LRCK 13 DEMP DGND POWER 4x/8x OVERSAMPLING DIGITAL SUPPLY FILTER & FUNCTION CONTROL 12 TEST ENHANCED MULTILEVEL ZERO...
  • Page 64 HCD-GT3D Ver. 1.1 IC902 RN5B801-0002 (MOTHERBOARD BOARD (2/10)) IISD IISD CP2 3 FM Antenna Digital Signal Process LOUT Filter Digital Stereo FRF1 4 Mixer Demodulator Decoder FM LNA ROUT Digital Demodulator Decoder LRCK GNDRF 5 LRCK / LOUT Image Station...
  • Page 65 HCD-GT3D IC912 TC74VHC157FT (EK) (MOTHERBOARD BOARD (4/10)) SELECT 11 1 1A 2 STROBE INPUT INPUT OUTPUT 11 12 OUTPUT INPUT INPUT OUTPUT GND 8 OUTPUT IC913 TC7WH157FK (MOTHERBOARD BOARD (4/10)) 11 7 11 6 SELECT EN G GND 4 IC914 PCM5101 (MOTHERBOARD BOARD (3/10))
  • Page 66 HCD-GT3D • IC Pin Function Descriptions MOTHERBOARD BOARD (9/10) IC101 R7S7200032CFP-A (SYSTEM CONTROLLER) Pin No. Pin Name Description SRC-RST0 Not used VIDEO-MUTE Muting Control for Video CDM-UNLOAD-SW CDM UNLOAD SW CDM-LOAD-SW CDM LOAD SW BT-RESET Reset signal output to Bluetooth section...
  • Page 67 HCD-GT3D Pin No. Pin Name Description SSI1_DI Data In Signal from ADC to Aragon SD_FAST SD FAST DETECT PCONT-PSAVE- Main power on/off control signal output “H”:power on PROTECT Power supply terminal (+3.3V) LINK-DET Party Chain input bias detection pin USB_HOST_SEL...
  • Page 68 HCD-GT3D Pin No. Pin Name Description Ground terminal TEST-MON108/ Test port for software checking SD_CLK PVcc Power supply terminal (+3.3V) TEST-MON110/ Test port for software checking SD_D0_0 ANALOG-DSEL/ ANALOG INPUT SELECTOR D SD_D1_0 RGB-TRANS-LED- Transfer signal to RGB driver (driver for Speaker LED)
  • Page 69 HCD-GT3D Pin No. Pin Name Description USBAVss Ground terminal USBUVcc Power supply terminal (+3.3V) USBUVss Ground terminal Ground terminal Ground terminal ANALOG-CSEL ANALOG INPUT SELECTOR C DIR-RESET DIR RESET Q-FLASH-SIO2 QSPI: Data I/O pins for channel 0 Q-FLASH-SIO3 QSPI: Data I/O pins for channel 0...
  • Page 70 HCD-GT3D MOTHERBOARD BOARD (5/10) IC301 CXD9990R (CD RF AMP FOCUS/TRACKING ERROR AMP, CD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Description RF_C RF main beam C input from the optical pick-up block RF_D RF main beam D input from the optical pick-up block...
  • Page 71 HCD-GT3D Pin No. Pin Name Description DQM0 Data mask signal output to the SD-RAM 62 to 69 RD15 to RD8 Two-way data bus with the SD-RAM DQM1 Data mask signal output to the SD-RAM DVDD33 Power supply terminal (+3.3V) (for digital system)
  • Page 72: Exploded Views

    HCD-GT3D Ver. 1.2 SECTION 7 EXPLODED VIEWS Note: • The mechanical parts with no reference • Abbreviation The components identifi ed by mark 0 number in the exploded views are not sup- : Argentina model or dotted line with mark 0 are critical for plied.
  • Page 73: Top Panel Section

    HCD-GT3D Ver. 1.2 7-2. TOP PANEL SECTION • Bottom view not supplied (BUTTON board) not supplied (MIC board) not supplied not supplied Note 1: When the VOLUME knob assy or MIC knob is replaced, Note 2: If wire (fl at type) is replaced, install it after bending it refer to “NOTE OF REPLACING THE VOLUME KNOB...
  • Page 74: Loading Panel Section

    HCD-GT3D Ver. 1.2 7-3. LOADING PANEL SECTION not supplied (OPTICAL board) CDM section not supplied not supplied not supplied MOTHERBOARD board section not supplied Ref. No. Part No. Description Remark X-2590-650-4 PANEL, LOADING ASSY 4-295-431-01 SPRING, LOADING 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3...
  • Page 75: Motherboard Board Section

    HCD-GT3D Ver. 1.2 7-4. MOTHERBOARD BOARD SECTION • Rear view not supplied not supplied not supplied (SPLITTER board) not supplied not supplied chassis section Note 1: When the complete DAMP board is replaced, refer to Note 2: If wire (fl at type) is replaced, install it after bending it “NOTE OF REPLACING THE IC1001 ON THE DAMP...
  • Page 76: Chassis Section

    HCD-GT3D Ver. 1.2 7-5. CHASSIS SECTION not supplied not supplied (RU, EA, MY, AUS, E4) not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied...
  • Page 77: Front Panel Section

    HCD-GT3D Ver. 1.2 7-6. FRONT PANEL SECTION • Rear view not supplied not supplied not supplied not supplied not supplied ND3000 not supplied not supplied not supplied not supplied (LCD board) not supplied not supplied not supplied not supplied (SPK_HLED board) not supplied Note: If wire (fl...
  • Page 78: Cdm Section

    HCD-GT3D Ver. 1.2 7-7. CDM SECTION CD mechanism section (CDM90-DVBU204//M) not supplied not supplied not supplied Ref. No. Part No. Description Remark 2-345-115-01 SCREW (S), FLOAT 4-535-577-01 STEP SCREW M2.6 4-533-382-01 INSULATOR 4-533-939-01 SPRING, INSULATOR (F) 4-533-940-01 SPRING, INSULATOR (R)
  • Page 79: Cd Mechanism Section (Cdm90-Dvbu204//M)

    HCD-GT3D Ver. 1.2 7-8. CD MECHANISM SECTION (CDM90-DVBU204//M) supplied (including MS-476 board) not supplied not supplied not supplied not supplied not supplied (MS-476 board) not supplied not supplied not supplied Note : If cable, fl exible fl at and wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.
  • Page 80: Electrical Parts List

    HCD-GT3D Ver. 1.2 SECTION 8 BUTTON ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • SEMICONDUCTORS The components identifi ed by mark 0 the parts list may be different from the In each case, u: μ, for example: or dotted line with mark 0 are critical for parts specifi...
  • Page 81 HCD-GT3D Ver. 1.1 DAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-2061-348-A DAMP BOARD, COMPLETE C1092 1-112-692-11 CERAMIC CHIP 1000PF * C1095 1-118-360-11 CERAMIC CHIP 0.1uF ********************* C1104 1-162-966-91 CERAMIC CHIP 0.0022uF < CAPACITOR >...
  • Page 82 HCD-GT3D Ver. 1.1 DAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > R1037 1-216-819-11 METAL CHIP 1/10W R1052 1-250-535-11 METAL CHIP 1/16W IC1001 6-716-817-01 IC TAS5630BPHDR * R1053 1-250-507-11 METAL CHIP 3.3K 1/16W...
  • Page 83 HCD-GT3D Ver. 1.1 DAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1161 1-216-864-11 SHORT CHIP R3022 1-216-864-11 SHORT CHIP R1162 1-216-864-11 SHORT CHIP R3025 1-216-296-11 SHORT CHIP R1163 1-216-864-11 SHORT CHIP R3026 1-216-821-11 METAL CHIP...
  • Page 84 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > A-2071-988-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (RU) IC3200 8-759-909-71 IC BA4558F ****************************************** < JACK > < CAPACITOR > J3200 1-822-967-12 JACK (MIC 1)
  • Page 85 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C105 1-162-966-91 CERAMIC CHIP 0.0022uF * C280 1-118-035-11 CERAMIC CHIP 0.1uF * C106 1-118-035-11 CERAMIC CHIP 0.1uF * C281 1-118-035-11 CERAMIC CHIP 0.1uF * C107 1-118-035-11 CERAMIC CHIP 0.1uF...
  • Page 86 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C372 1-116-717-11 CERAMIC CHIP 10uF C626 1-116-865-11 CERAMIC CHIP 10uF C373 1-112-692-11 CERAMIC CHIP 1000PF C627 1-116-865-11 CERAMIC CHIP 10uF C401 1-165-492-21 ELECT CHIP...
  • Page 87 HCD-GT3D Ver. 1.2 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C905 1-165-492-21 ELECT CHIP 100uF < DIODE > C906 1-165-908-11 CERAMIC CHIP 1uF C917 1-116-716-11 CERAMIC CHIP 10uF D102 6-502-961-01 DI DA2J10100L C922 1-118-386-11 CERAMIC CHIP 0.1uF...
  • Page 88 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JACK > < RESISTOR > J602 1-844-218-11 JACK, PIN 4P R002 1-208-709-11 METAL CHIP 0.50% 1/16W (AUDIO PARTY CHAIN IN L/R / OUT L/R)
  • Page 89 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R127 1-218-965-11 METAL CHIP 1/16W R201 1-218-941-81 METAL CHIP 1/16W R128 1-218-953-11 METAL CHIP 1/16W R202 1-218-965-11 METAL CHIP 1/16W R129 1-218-941-81 METAL CHIP...
  • Page 90 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R273 1-218-941-81 METAL CHIP 1/16W R354 1-218-990-81 SHORT CHIP R274 1-218-941-81 METAL CHIP 1/16W R355 1-218-990-81 SHORT CHIP R275 1-218-949-11 METAL CHIP 1/16W R356...
  • Page 91 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R466 1-216-295-91 SHORT CHIP R607 1-218-985-11 METAL CHIP 470K 1/16W R467 1-216-295-91 SHORT CHIP R608 1-218-961-11 METAL CHIP 4.7K 1/16W R470 1-218-990-81 SHORT CHIP...
  • Page 92 HCD-GT3D Ver. 1.1 MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R682 1-218-973-11 METAL CHIP 1/16W R840 1-218-933-11 METAL CHIP 1/16W R684 1-218-973-11 METAL CHIP 1/16W R857 1-216-864-11 SHORT CHIP R685 1-218-978-11 METAL CHIP 120K...
  • Page 93 HCD-GT3D Ver. 1.2 MS-476 OPTICAL SPK_HLED SPLITTER MOTHERBOARD Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X600 1-814-365-11 QUARTZ CRYSTAL UNITS (12MHz) 1-849-010-11 WIRE (FLAT TYPE) (25 CORE) X602 1-814-130-11 QUARTZ CRYSTAL UNIT (24.576MHz) * 202...
  • Page 94 HCD-GT3D Ver. 1.2 MEMO...
  • Page 95 HCD-GT3D REVISION HISTORY Ver. Date Description of Revision 2015.02 2015.06 Addition of African, Argentina, Malaysia, Russian, Saudi Arabia and Thai models. Add note for IC101 in page 5, 39, 48 and 87. Change description of IC303, IC601 and IC603 in MOTHERBOARD board.
  • Page 96 HCD-GT3D Ver. Date Description of Revision Delete four pieces of CUSHION (D-AMP) on SUB CHASSIS in page 15, 16, 75 and 76. Delete four pieces of CUSHION (SMPS) on CHASSIS in page 17 and 76. Delete four pieces of CUSHION, BUTTON on CDM section in page 13, 74 and 78.

Table of Contents