Summary of Contents for Blue Diamond Mini Pickup Broom
Page 1
Mini Pickup Broom Operation and Maintenance Manual Register your WARRANTY within 30 days of purchase 888-376-7027 | BlueDiamondAttachments.com...
Introduction: Owner Information Serial Number Location: Thank you for your decision to purchase a Blue Dia- mond Mini Pickup Broom. To ensure maximum per- Please record attachment information in the space pro- formance of your equipment, it is mandatory that you vided for future reference.
The CRUSHING HAZARD decal warns the operator and bystanders to stay away during operation. DO NOT get on a moving or operating broom or attachment. NEVER jump on or off a running attachment or loader. Blue Diamond® Attachments...
Wire Harness The wiring harness to the optional water spray kit pump should be routed to prevent catching or pinching when sweeping or dumping operations. Attaching to Loader WARNING Never crawl under raised loader arms or attachment. Blue Diamond® Attachments...
(See illustration below). Operating Tips - Optional Water Kit Check the strainer bowl daily for dirt and debris. This debris can plug the nozzles. Check nozzles daily for debris. Remove and clean plugged nozzles. Blue Diamond® Attachments...
DO NOT store the polypropylene brush wafers in direct sun light. The material can deteriorate. Raise broom housing and take weight off of broom wafers. Store broom with bucket stop pins in the lowest position to relieve ground pressure on broom core. Blue Diamond® Attachments...
Lower broom to ground, set loader brake and dismount loader. 6. Measure pattern width left by broom. Pattern should be 2”-4” wide. 7. To adjust pattern, carefully prop up the broom shroud assembly. Remove the two bent leg Blue Diamond® Attachments...
6. Loosen set screws and remove sprocket and bearing. 3. Loosen chain tensioner sprocket and remove chain. 7. Remove end retainer from one broom end. 4. Remove bearing guard on the right hand side, and remove hardware from both bearings. 8. Remove wafers. Blue Diamond® Attachments...
6. Reassemble in reverse order from 4.2 “Removing Broom Wafers” on page 10. Confirm all hardware is torqued appropriately. See 4.6 2. Install a new wafer making sure wafer retention “Fastener Torque Specifications” on page 14. pins are trapped on broom drum bar. Blue Diamond® Attachments...
2. Remove chain cover. Loosen and remove chain. 5. Remove motor mount plate and unbolt from motor. 6. Reassemble in reverse order. Confirm all hardware is torqued appropriately. See 4.6 “Fastener Torque Specifications” on page 14. 3. Remove drive sprocket. Blue Diamond® Attachments...
5. Remove bearing hardware. Loosed set screws and remove bearings. 3. Remove shaft sprocket. 6. Replace bearings and reassemble in reverse order. Confirm all hardware is torqued appropriately. See 4.6 “Fastener Torque Specifications” on page 14. Blue Diamond® Attachments...
5.4 Water Kit Breakdown WATER PUMP ASSEMBLY WATER PUMP ASSEMBLY PICKUP BROOM WATER KIT ITEM PART NUMBER DESCRIPTION QTY 42” QTY 48” QTY 54” 316565 Water Kit - 42" 316567 Water Kit - 48" 316569 Water Kit - 54" Blue Diamond® Attachments...
Page 21
Plastic Barbed Hose Fitting 216854 Mini Pub - Spray Bar - Base - Weldment For 42” 216856 Mini Pub - Spray Bar - Base - Weldment For 48” 216858 Mini Pub - Spray Bar - Base - Weldment For 54” Blue Diamond® Attachments...
® warranty of any kind, expressed or implied, AND MAKES NO WARRANTY OF MERCHANTABILITY IN RESPECT TO ITS MACHINERY AND/OR ATTACHMENTS ARE FIT FOR ANY PARTICULAR PURPOSE. BLUE DIAMOND ® ATTACHMENTS shall not be liable for incidental or consequential damages for any breach or warranty, including but not limited to inconvenience, rental of replacement equipment, loss of profits or other commercial loss.
Page 24
QUALITY | DEPENDABILITY | INTEGRITY Blue Diamond® Attachments 4512 Anderson Road, Knoxville, TN 37918 888-376-7027...
Need help?
Do you have a question about the Mini Pickup Broom and is the answer not in the manual?
Questions and answers