Cisco PA-T3 Installation And Configuration Manual page 61

For a Catalyst RSM/VIP2, the show interfaces port-adapter/port command displays status
information for the interfaces you specify. In this example, a one-port PA-T3 serial port
adapter-configured Catalyst RSM/VIP2 is in port adapter slot 0.
router# show interfaces serial 0/0
Serial0/0 is up, line protocol is up
Hardware is cyBus PODS3 Serial
MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set, keepalive not set
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
14771 packets input, 3032919 bytes, 0 no buffer
Received 2664 broadcasts, 0 runts, 0 giants
0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
15775 packets output, 2808513 bytes, 0 underruns
0 output errors, 0 applique, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
rxLOS inactive, rxLOF inactive, rxAIS inactive
txAIS inactive, rxRAI inactive, txRAI inactive
router#
For Cisco 7100 series, Cisco 7200 series, and Cisco uBR7200 series routers, use the
show controllers command to display all the current interface processors and their interfaces.
Following is an example of the show controllers command that shows serial port 2/0 on a one-port
PA-T3 serial port adapter installed in chassis slot 2 for a Cisco 7200 series router:
router# show controllers 2/0
M1T-Serial: show controller:
PAS unit 0, subunit 0, f/w version 1-23, rev ID 0x1, version 2
idb = 0x608PA-T3340, ds = 0x608E50C0, ssb=0x608E5A84
Clock mux=0x35, ucmd_ctrl=0x8, port_status=0x25
maxdgram=4474, bufpool=64Kb, 128 particles
TM=down CA=up
line state: up
Serial DTE cable
(Additional display text omitted from this example.)
For Cisco 7100 series, Cisco 7200 series, Cisco uBR7200 series routers, use the show controllers
serial command, using arguments such as the slot and port number (slot/port), to display information
that is specific to the serial interface hardware. Following is an example of the show controllers
serial slot/port command that shows the serial port adapter installed on a Cisco 7200 series router
in chassis slot 3:
router# show controllers serial 3/0
M1T-T3 pa: show controller:
PAS unit 0, subunit 0, f/w version 2-55, rev ID 0x2800001, version 2
idb = 0x60C03278, ds = 0x60C07704, ssb=0x60C05298
Clock mux=0x30, ucmd_ctrl=0x0, port_status=0x0
Serial config=0x8, line config=0x1B0202
maxdgram=4480, bufpool=128Kb, 256 particles
rxLOS active, rxLOF inactive, rxAIS inactive
txAIS active, rxRAI inactive, txRAI active
Using show Commands to Display Interface and System Information
LC=down
Configuring the PA-T3 Interfaces 8-17