Prior To Operation - DeWalt D28710 Original Instructions Manual

2. Pull down the arm and lock it in this position using the lock-
down chain 20 (Fig. A).
3. Place a square 36 against the fence
the cutting disc creating a perfect 90° (Fig. D). Check that
the 0° marking on the scale
the table 37 .
4. Tighten the fence bolts 34
5. Release the lock-down chain
upper rest position (Fig. A).
Adjusting the Spark Deflector (Fig. A)
1. Loosen the screw .
19
2. Set the spark deflector 18
3. Tighten the screw 19 .
Mounting (Fig. F, G)

CAUTION: Tool must be supported on stable, level,
non-skid surface to prevent unexpected movement
when operating.
Procedure For Permanent Mounting
1. Drill two holes 8 mm through the work surface (Fig. F).
2. Insert 1/4–20 screws down through the holes in the base
and through holes in mounting surface. The approximate
length of the screws should be the thickness of the
mounting surface plus 102 mm.
3. Tighten both screws securely.
Cradle Mounting
1. Cut two boards approximately 508 x 50.8 x 101.6 mm wide.
2. Place chop saw at desired work location.
3. Place boards tightly along side, and nail to work surface
(Fig. G).

Prior to Operation

• Install the appropriate cutting disc. Do not use excessively
worn discs. The maximum rotation speed of the tool must
not exceed that of the cutting disc.
• Make sure the disc rotates in the direction of the arrows on
the accessory and the tool.
• Secure the workpiece.
• Always set the spark deflector correctly.
OPERATION
Instructions for Use

WARNING:
• Always observe the safety instructions and
applicable regulations.
• Do not apply excessive pressure to the tool.
• Avoid overloading. Should the tool become hot, let it
run a few minutes under no-load condition.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
8 and the left side of
aligns with the marking on
35
to lock the fence 8 .
and return the arm to its
20
as appropriate.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the operating
handle 3 , with the other hand guiding the workpiece.
Performing a Cut (Fig. A)
1. Place the material to be cut against the fence
using the material clamp 9
2. Turn the tool on and pull down the operating handle
to cut the workpiece. Allow the motor to reach full speed
before cutting.
3. Allow the disc to cut freely. Do not force.
4. After completing the cut, switch off the tool and return the
arm to its upper rest position.
Switching On and Off (Fig. A)
The on/off switch 1 is mounted in the operating handle
• To run the tool, press the on/off switch
• Keep the on/off switch depressed while performing
the operation.
• To stop the tool, release the switch.

WARNING: Do not switch the tool on or off when
under load.

WARNING: Do not cut magnesium.
Transporting (Fig. A)
The tool is equipped with a lock-down chain
the tool in closed-down position for carrying.
1. Lower the guard 15 onto the cutting table
the tool in this position by hooking the chain
lock-down hook 17 .
2. Transport the tool using the carrying handle
3. To release the tool, depress the operating handle
and release the chain.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
EngLIsh
8 and secure
.
3
3 .
1 .
20 which locks
10 and secure
20 over the
.
4
3 slightly
25