Bosch GBM 13-2 RE Original Instructions Manual page 14

OBJ_BUCH-2291-005.book Page 14 Tuesday, April 17, 2018 3:39 PM
14 | English
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Technical Data
Rotary drill
Article number 3 601 ... ... AB2 006 ... AB2 004 ... AB2 005 ... AB2 031 ... AB2 062 ... AB2 071 ... AB2 041
Rated power input
Output power
No-load speed
– 1st gear min
– 2nd gear min
Rated speed
– 1st gear min
– 2nd gear min
Rated torque
(1st/2nd gear) Nm
Spindle collar dia. mm
Speed preselection
Speed control
Right/left rotation
Overload Clutch
Keyless chuck with
securing ring
Keyless Chuck
Key type drill chuck
Maximum drilling diam-
eter (1st/2nd gear)
– Steel mm
– Wood mm
– Aluminium mm
Chuck clamping range mm
Weight according to
EPTA-Procedure
01:2014 kg
Protection class
Assembly
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle 9.
The auxiliary handle 9 can be set in 12 positions to achieve a
safe and low-fatigue working stance.
Turn the bottom part of the auxiliary handle 9 in rotation di-
rection  and push the auxiliary handle 9 forward until you
can pivot it to the desired position. Then pull the auxiliary han-
dle 9 back again and tighten it by turning the bottom part of
the auxiliary handle in rotation direction .
1 609 92A 4SD | (17.4.18)
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
W 750 750
W 353 353
-1
0 – 1000 0 – 1000 0 – 1000
-1
0 – 3000 0 – 3000 0 – 3000
-1
500 500
-1
1750 1750
6.8/2.5 6.8/2.5 6.8/2.5
43 43
 
 
 
 

–

–
– –
13/8 13/8
32/20 32/20
20/12 20/12
1 – 13 1 – 13
2.4 2.4
/II /II
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop
10.
Turn the bottom part of the auxiliary handle 9 in anticlockwise
direction and insert the depth stop 10.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Afterwards, tighten the bottom part of the auxiliary handle 9
again by turning in clockwise direction.
The knurled surface of the depth stop 10 must face upward.
750 750 750
353 353 374
0 – 1000 0 – 1000
0 – 3000 0 – 3000
500 500 500
1750 1750 1750
6.8/2.5 6.5/2.2
43 43 43
  
  
  
  
– – –
 
–

– –
13/8 13/8 13/8
32/20 32/20 32/20
20/12 20/12 20/12
1 – 13 1 – 13 1 – 13
2.4 2.4 2.4
/II /II /II
GBM 13-2 RE
710 750
365 353
0 – 1 100
0 – 1000
0 – 3 400
0 – 3000
500 500
1750 1750
6.5/2.2 6.8/2.5
43 43
 
 
 
 

–

–
– –
13/8 13/8
32/20 32/20
20/12 20/12
1 – 13 1 – 13
2.4 2.4
/II /II
Bosch Power Tools