Specifications - Makita DJS160 Instruction Manual

ENGLISH (Original instructions)
1-1. Button
1-2. Red indicator
1-3. Battery cartridge
2-1. Star marking
3-1. Switch lever
4-1. Indicating lamp
5-1. Hex wrench
5-2. Screw

SPECIFICATIONS

Model
Max. cutting capacities
Min. cutting radius
Strokes per minute (min
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
Noise
The typical A-weighted
according to EN60745:
Model DJS100, DJS101, DJS161
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DJS160
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Model DJS100
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Explanation of general view
6-1. Center blade
6-2. Thickness gauge
6-3. Side blade
6-4. Hex wrench
6-5. Hex socket head bolt
7-1. Hex wrench
8-1. Oil supply
8-2. Center blade
2
Steel up to 400 N/mm
2
Steel up to 600 N/mm
2
Aluminum up to 200 N/mm
-1
)
noise level determined
) : 71 dB (A)
pA
) : 74 dB (A)
pA
value (tri-axial vector
2
) : 12.5 m/s
h
2
DJS160 DJS161
1.6 mm (16 ga.)
1.2 mm (18 ga.)
2.5 mm (13 ga.)
250 mm
4,300
362 mm
1.9 kg 2.0 kg
D.C. 14.4 V D.C. 18 V
ENE037-1
Model DJS101, DJS161
Work mode : cutting sheet metal
Vibration emission (a
ENG905-1
Uncertainty (K) : 1.5 m/s
Model DJS160
Work mode : cutting sheet metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
ENG900-1
used.
sum) Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
8-3. Pin
11-1. Limit mark
12-1. Brush holder cover
12-2. Notch
12-3. Screwdriver
13-1. Brush holder cap
13-2. Screwdriver
DJS100
1.0 mm (20 ga.)
0.7 mm (23 ga.)
2.5 mm (12 ga.)
30 mm
4,300
364 mm
1.9 kg
D.C. 14.4 V
2
) : 13.0 m/s
h
2
2
) : 12.0 m/s
h
2
DJS101
2.0 kg
D.C. 18 V
ENG901-1