Table of Contents
Advertisement
Section 1.
General Description
Section 2.
Installing The Control
Mounting the Cabinet .................................................................................................. 2Ð1
Installing the Lock (if used) ........................................................................................ 2Ð1
Installing the Control's Circuit Board Alone
or (if used), With a 4204, 4219, or 4229 Module .................................................... 2Ð2
Installing Control and RF Receiver Circuit Boards Together in the Cabinet ........... 2Ð3
Standard Phone Line Connections .............................................................................. 2Ð4
Wiring the AC Transformer ......................................................................................... 2Ð4
Installing the Back-Up Battery ................................................................................... 2Ð5
Earth Ground Connections .......................................................................................... 2Ð5
Section 3.
Installing Remote Keypads
General Information ..................................................................................................... 3Ð1
Keypads that May Be Used ......................................................................................... 3Ð1
Wiring to the Keypads .................................................................................................. 3Ð1
Wiring Run Chart for Devices Drawing AUX Power From the Control ............. 3Ð2
Mounting the Keypads ................................................................................................. 3Ð2
Using A Supplementary Power Supply To Power Additional Keypads .................... 3Ð2
Preliminary Check-Out Procedure .............................................................................. 3Ð3
Section 4.
Basic Hard-Wired Zones 1–6
Installing the Hard-Wired Zones ................................................................................. 4Ð1
Common Characteristics For Zones 1Ð6 ............................................................... 4Ð1
Wiring Burglary and Panic Devices to Zones 1Ð6 ................................................ 4Ð1
Wiring 4-Wire Smoke/Combustion Detectors ....................................................... 4Ð1
Compatible 4-Wire Smoke/Combustion Detectors ............................................... 4Ð2
Programming Hard-Wired Zones ................................................................................ 4Ð2
Programming Panic Keys............................................................................................. 4Ð4
Check-Out Procedure for Hard-Wired Zones .............................................................. 4Ð5
Section 5.
Wired Zone Expansion (4219, 4229)
General Information ..................................................................................................... 5Ð1
Installing Zone Expansion Units ................................................................................. 5Ð1
Connections and Set-Up ........................................................................................ 5Ð1
Programming Wired Expansion Zones........................................................................ 5Ð2
Check-Out Procedure for Wired Expansion Zones ..................................................... 5Ð3
Section 6.
Wireless (RF) Zone Expansion (5800 RF Systems)
Wireless Systems Available ......................................................................................... 6Ð1
Wireless System Operation and Transmitter Supervision ........................................ 6Ð1
Transmitter Battery Life ....................................................................................... 6Ð2
Receiver Supervision .............................................................................................. 6Ð2
Wireless System Installation Advisories .............................................................. 6Ð2
Installation and Setup of the 5881 Series Wireless Receiver..................................... 6Ð2
Installing the 5800TM Module .................................................................................... 6Ð2
Programming the Control For Wireless ...................................................................... 6Ð3
Enrolling 5800 Series Transmitters ...................................................................... 6Ð4
5800 Series Transmitter Input Loops ................................................................... 6Ð4
5800 Series Transmitter Input Types ................................................................... 6Ð4
Compatible 5800 Series Transmitters ................................................................. 6Ð5
Table Of Contents
................................................................................................. 1Ð1
.............................................................................................. 2Ð1
.................................................................................... 3Ð1
.................................................................................. 4Ð1
..................................................................... 5Ð1
.......................................... 6Ð1
iii
- Quick Links:
- Keypads that May be Used
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the FA147C and is the answer not in the manual?
Questions and answers
how do i change the battery
To change the battery in a First Alert FA147C:
1. Open the control panel.
2. Disconnect AC power by removing the lead on the far left terminal.
3. Disconnect the old battery.
4. Connect the new battery to the battery terminals.
5. Reconnect the AC power to the far left terminal.
Make sure to connect the battery only when instructed and follow safety precautions.
This answer is automatically generated