General Assembly Guidelines Ensure that all parts and hardware are available before beginning assembly. Follow each step carefully to ensure the proper assembly of this product. III. Two people are recommended for ease in the assembly of this product. The three main types of hardware used to assemble this product are: wood dowels, screws and bolts.
Page 5
Step 1 Insert wooden dowel (A) into part (3) ,then secure cam bolt (B) into part (3) with Philips head screwdriver as per diagram.
Page 6
Step 2 Insert wooden dowel (A) into part (4) ,then secure cam bolt (B) into two sides of part (4) with Philips head screwdriver as per diagram.
Page 7
Step 3 Insert wooden dowel (A) into parts(9,14),using screw (black) (P) attach hook (M) to part (9),Door stopper (N) to parts(1,14)with Philips head screwdriver .using bolts (S,T) attach part (15) to part (2) , using bolt (S) attach part(12) to part (2) with hex key (R) as per diagram .
Page 8
Step 4 Insert wooden dowel (A) into parts (10,11) ,Secure cam bolt (B) into part (10) then using cam lock (C) attach part (11) into part (10) with Philips head screwdriver as per diagram .
Page 9
Step 5 Using cam lock (C) attach parts (9,10,11) to part (4) with Philips head screwdriver as per diagram.
Page 10
Step 6 Using cam lock (C) attach part (14) to part (4) with Philips head screwdriver as per diagram. P.10...
Page 11
Step 7 Using cam lock (C) attach part (14) to part (3) with Philips head screwdriver as per diagram. P.11...
Page 12
Step 8 Using screw (E) attach part (2) into parts (3,4,11) with hex key (R) as per diagram. P.12...
Page 13
Step 9 Using bolt (S) attach part (5) to parts (2,9,10) with hex key (R) as per diagram. P.13...
Page 14
Step 10 Put part (6) as per diagram. P.14...
Page 15
Step 11 Using bolt(T,E ) attach part (1) into part (3,4,5) with hex key (R) as per diagram .please kindly note that keep the back panel into the groove of part (1) then secure all the bolts. P.15...
Page 16
Step 12 Place sticker (D) cover the holes as per diagram . P.16...
Page 17
Step 13 Using screw (X) attach Velcro strap (U) into part (1) with Philips head screwdriver as per diagram. P.17...
Page 18
Step 14 Using screw (G) secure plastic wedge (F) into part (6) with Philips head screwdriver as per diagram. P.18...
Page 19
Step 15 Insert shelf support pin (Q) into parts (3,4) as per diagram. Make sure you place the four shelf support pins (Q) in the same level. So the shelf is not titled .Put part (13) into unit as per diagram. Tilt and rest the adjustable shelf(13) onto the shelf support pins .
Page 20
Step 16 Using bolt (J) attach handle (H) into parts (7,8) ,and using screw(L) attach Europe hinge (K) to parts (7,8) with Philips head screwdriver as per diagram. P.20...
Page 21
Step 17 Using screw(L) attach Europe hinge (K) to part (3) with Philips head screwdriver as per diagram. Open and close the doors to make sure they were shut correctly .if necessary ,adjust the screws for a good fit . P.21...
Page 22
Step 18 WARNING Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over we recommend that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors.
Page 23
Step 19 Position the assembled unit at the desired location .if necessary ,adjust the floor leveler at the bottom of support leg to level the unit . P.23...