Advertisement
Quick Links
Halsey Taylor Owners Manual
OVL
™
HTHB-OVLSEBP-I
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an "electrolysis" effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain fittings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building's plumbing circuits.
HTHB-OVLSEBP-I
Fountains with Dual-Stream Bubbler
and HydroBoost
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
HTHBWF-OVLSEBP-I
Bottle Filler
™
HTHBWF-OVLSEBP-I
Page 1
™
0000001032 (Rev. A - 10/13)
Advertisement
Related Manuals for Halsey Taylor HTHB-OVLSEBP-I
Summary of Contents for Halsey Taylor HTHB-OVLSEBP-I
- Page 1 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I Halsey Taylor Owners Manual Fountains with Dual-Stream Bubbler ™ ™ and HydroBoost Bottle Filler ™ HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I INSTALLER Review these instructions before beginning installation. Be sure that installation conforms to all plumbing, electrical and other applicable codes. When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
- Page 2 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I Fig. 1 0000001032 (Rev. A - 10/13) Page 2...
-
Page 3: Required Tools And Materials
1. Make water supply connections (Fig 13). Install a shut-off valve and union connection to building water supply (valve and union not provided). Turn on water supply and flush Figure 2 - HTHB-OVLSEBP-I Tube Routing the line thoroughly. Caution: DO NOT SOLDER tubes inserted into the strainer or filter head as damage to the o-rings may result. - Page 4 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I 43, 44, 45, 46, 47 8. Install reset switch and mating bracket on lower fountain (lower right bolt) for bottle filler (Fig 5). Connect the switch wire to the extension wire on the back of the bottle filler. Wrap up the excess cord.
- Page 5 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I Regulator Mounting Bracket Figure 9 Stream Height Adjustment Regulator Assembly Figure 7 Regulator Mounting Mechanism See Fig. 6 See Fig. 7 See Fig. 8 See Fig. 9 Figure 8 - Push Bar Mechanism Figure 10 - Drain Assembly...
- Page 6 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I BF11 PROGRAM SETTING THE CONTROL BOARD VERIFY CONTROL BOARD SOFTWARE Continued from below: 1) To verify the software program of the control board the unit will 2) When the display changes to “SETTINGS”, depress the button again. need to be shut down and restarted. The chiller (if present) does The display will change to show not need to be shut down and restarted.
- Page 7 HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I MAIN PANEL DRAIN MOUNTING FILTER (OPTIONAL) LOCATION FRAME MOUNTING FRAME FIG. 12 3/8” O.D. UNPLATED COP- 1/4” O.D. TUBE BUILDING WATER PER TUBE CONNECT WATER INLET INLET COLD WATER SUPPLY TO COOLER SERVICE STOP NOTE: WATER FLOW Note: Screw the locknut hand tight to seal...
-
Page 8: Parts List
HTHB-OVLSEBP-I HTHBWF-OVLSEBP-I PARTS LIST Installation Package ITEM NO. PART NO. DESCRIPTION 51546C Bubbler The components for installation are packed in 27006C Basin two separate boxes, regardless of the type of unit 27000C Lower Shell being installed. The boxes contain the following:...