Panasonic KX-FP207FX-S Service Manual page 64

KX-FP207FX-S/FP218FX-S
Code Function
580 TAM continuous tone detection (KX-
FP218)
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
599 ECM frame size
710 Memory clear except History data
717 Transmit speed selection (KX-FP207) 1:9600BPS
717 Transmit speed selection (KX-FP218) 1:14400BPS
718 Receive speed selection (KX-FP207) 1:9600BPS
718 Receive speed selection (KX-FP218) 1:14400BPS
722 Redial tone detect
745 Power ON film feed
763 CNG detect time for friendly reception 1:10 sec
773 DIS-DIC interval
774 T4 timer
784 Voice prompt test (KX-FP218)
815 Sensor & Vox check
Set Value Effective
Range
1:ON 2:OFF 1, 2
X number of 00~99
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
1:75 msec 1~3
2:500 msec
3:1 sec
1:detects at 1, 2
the 1st time
2:detects at
the 2st time
1:5 % 1~4
2:10 %
3:15 %
4:20%
X dbm - 15~00
(10 = -10 dbm)
X dbm -20~-48
(40 = -40 dbm)
1:256 2:64 1, 2
1~4
2:7200BPS
3:4800BPS
4:2400BPS
1~6
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~4
2:7200BPS
3:4800BPS
4:2400BPS
1~6
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1~3
2:20 sec
3:30 sec
1: 500msec 1, 2
2: 200msec
X 100 msec 00~99
64
Default
1 ON : Stops TAM operation when Dial tone, etc. are
detected.
05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
065 Sets the FAX redial interval during FAX communication.
2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialling is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.90).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot either transmit/receive long distance or
international communications (P.93). Refer to
Receive Problem (P.91) .
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot either transmit/receive long distance or
international communications (P.93). Refer to Some-
time there is a transmit problem (P.90).
2 Refer to Receive Problem (P.91).
10 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.90) and Receive Prob-
lem (P.91).
42 Used when there is an error problem. Refer to The unit
can copy, but cannot either transmit/receive long
distance or international communications (P.93).
Power is OFF/ON after changing this set value.
1
Refer to Memory Clear Specification (P.66).
1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.90) and The unit can copy, but the transmission
and reception image are incorrect (P.95).
1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.90) and The unit can copy, but the transmission
and reception image are incorrect (P.95).
1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.91) and The unit
can copy, but the transmission and reception image
are incorrect (P.95).
1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.91) and The unit
can copy, but the transmission and reception image
are incorrect (P.95).
1 Sets the tone detection mode after redialling.
1 When the power is turned on, the film is wound to take
up any slack.
3 Selects the CNG detection tone of friendly reception.
2 This is similar to #594. The time interval from receiving
DIS to sending DCS can be changed to wait for the
echo canceler to recover.
0 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
See Test Mode (P.58).
See Test Mode (P.58).
Remarks
----------