Related Manuals for Hinkley SAWYER 36
Summary of Contents for Hinkley SAWYER 36
- Page 1 36" SAWYER ™ INDOOR / OUTDOOR LED FAN DC MOTOR WIFI CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
INSTALLING THE HANGING BRACKET SPECIFICATIONS HANGING THE FAN SMART BY BOND ELECTRICAL CONNECTIONS FINISHING THE INSTALLATION INSTALLING THE MONTING PLATE WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2020 Hinkley Lighting, Inc. | hinkley.com |... - Page 4 If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. | hinkley.com...
-
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2020 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
flat washers, wire nuts), MH902928Fxx Rubber Gasket, Balance Kit, Safety cable hardware(wood screw, flat washer) NOTE: Design of parts shown above may look slightly different for your specific model of fan. XX=FAN FINISH | hinkley.com... -
Page 7: Preparation
Loosen screw with key slot and remove canopy. Flat Washer Lock Washer Attach hanging bracket to outlet box using screws provided with the Outlet Box outlet box. Screw Fig. 1 ©2020 Hinkley Lighting, Inc. | hinkley.com |... -
Page 8: Hanging The Fan
Tighten security set screws against downrod using a large Hook-up flat blade screwdriver to ensure a tight fit against downrod. (3) Wires Tighten nuts against mounting collar. Downrod Security Screws Mounting Collar Cotter Pin Downrod Pin Top of Fan Body Fig. 2 | hinkley.com... - Page 9 Safety Cable Loop of the cable into the clamp and pull as much cable through as Wood Screw possible. Firmly tighten screw in the clamp. Cut off excess cable. And Washer Safety Cable Fig. 4 ©2020 Hinkley Lighting, Inc. | hinkley.com |...
-
Page 10: Electrical Connections
Connect the WHITE receiver neutral wire to the WHITE building neutral wire. Connect the COPPER building ground wire to the 4 YELLOW/GREEN ground wires from the fan and receiver. YELLOW GRAY BLACK WHITE Hanger Bracket Receiver Fig. 2 Fig. 1 | hinkley.com... -
Page 11: Finishing The Installation
C-Ring on the fan downrod. Slide the C-Ring up the downrod until the chains are taunt. Secure the C-Ring into position on the downrod by securing the two set screws. Allen Screws Secure Allen Wrench Ring Chain Support Loops. ©2020 Hinkley Lighting, Inc. | hinkley.com |... -
Page 12: Installing The Monting Plate
NOTE: Be sure the power is off before installing. Install 8 x 4-W LED bulbs (included). Glass Shades Raise the glass shade against the light holder and turn clockwise until snug, DO NOT OVERTIGHTEN. Restore power is ready for operation. Blubs Fig. 3 | hinkley.com... -
Page 13: Installing The Wall Control
Remote transmitter will be held in place with built in magnets. Cradle B Wall plate Plastic Face plate Outlet box anchor Transmitter Wall plate Cradle A Face plate Transmitter Wall Fig. 1 HIRO Control System Fig. 2 ©2020 Hinkley Lighting, Inc. | hinkley.com |... - Page 14 Attach the cradle A to the wall switch box using the supplied hardware. Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora face plate. Remote transmitter will be held in place with built in magnets.
-
Page 15: Operation
NOTE: A single fan can be controlled with as many as 3 wall controls in one room. Every control will need to repeat the pairing process based on instructions above and all controls must be within 30 feet of the fan. ©2020 Hinkley Lighting, Inc. | hinkley.com |... - Page 16 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 | hinkley.com...
-
Page 17: Care And Cleaning
Do not insert foreign objects between rotating fan blades. 1. Do not connect the fan with a wall mounted variable speed control(s). Remote Control Malfunction. 2. Make sure the dip switches are set correctly. ©2020 Hinkley Lighting, Inc. | hinkley.com |... -
Page 18: Energy Guide
• Your cost depends on rates and use Amps • Energy Use: 8 Watts All estimates based on typical use, excluding lights ftc.gov/energy RPMs Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Downrod | hinkley.com... -
Page 19: Smart By Bond
SMART BY BOND HINKLEY SMART FAN OPTIONS: • Brute Force Method In addition to the included wall control, you can control your Hinkley fan a) Turn mains power OFF to the fan. through the Bond app. b) Turn mains power back ON on the fan. - Page 20 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 21 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...