Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hinkley INDY FLUSH
Summary of Contents for Hinkley INDY FLUSH
- Page 1 72" INDY FLUSH ™ INDOOR / OUTDOOR LED FAN CEILING FAN INSTRUCTION MANUAL...
- Page 2 SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH HINKLEY A POSITIVE ONE. > SERVICE@HINKLEY.COM > 800.HINKLEY > LET’S SEE THAT HINKLEY STYLE @HINKLEY...
-
Page 3: Table Of Contents
INSTALLING THE HANGING BRACKET ENERGY GUIDE HANGING THE FAN SPECIFICATIONS ELECTRICAL CONNECTIONS SMART BY BOND FINISHING THE INSTALLATION INSTALLING THE BLADES WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 4: Instructions
If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. | hinkley.com... -
Page 5: Important Safety Precautions
These factors must be supplied by the person(s) installing, caring for and operating the unit. TOOLS & MATERIALS REQUIRED • PHILLIPS SCREWDRIVER • FLAT SCREWDRIVER • WRENCH OR PLIERS • WIRE CUTTER • STEPLADDER • WIRING SUPPLIES AS REQUIRED BY ELECTRICAL CODE ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 6: Unpacking Your Fan
flat washers, wire nuts), Blade to Motor Screws MH901058Fxx with Lock Washers, Balance Kit, Safety cable hardware (wood screw, flat washer) XX=FAN FINISH NOTE: Design of parts shown above may look slightly different for your specific model of fan. | hinkley.com... -
Page 7: Preparation
The bracket outlet box must be able to support a minimum of 35 pounds. Attach mounting bracket to outlet box using screws provided with the outlet box. Screws Fig. 1 ©2021 Hinkley Lighting, Inc. | hinkley.com |... - Page 8 Wood Screw possible. Firmly tighten screw in the clamp. Cut offffexcess cable. And Washer (Fig. 2) Safety Cable You are now ready to make the electrical connections. Fig. 2 | hinkley.com...
-
Page 9: Electrical Connections
"AC in L" from the receiver. Connect the white(neutral) wire from the ceiling to the white wire marked "AC in N" from the Receiver. Secure the wire connections with the plastic wire nuts provided. Fig. 1 ©2021 Hinkley Lighting, Inc. | hinkley.com... -
Page 10: Finishing The Installation
Mounting studs housing clockwise until snug. (Fig. 2) Mounting Washers Bracket Nuts Motor Fig. 1 Studs Motor Bracket Supports Motor Housing Fig. 2 hinkley.com... - Page 11 Use a large flat blade screwdriver for final tightening to fully compress the washers. This will help ensure proper alignment of the blades and Blade Arm noise-free, wobble-free running. Blade Screws Fig. 1 ©2021 Hinkley Lighting, Inc. | hinkley.com |...
- Page 12 Be sure the power is off before installing. Attach the lower cover to the mounting hub by turn the decorative cover clockwise until tight. Turn the power on. Your Hinkley Ceiling Fan is now ready to enjoy! Mounting Hub Decorative Cover Fig.
-
Page 13: Installing The Wall Control
Remote transmitter will be held in place with built in magnets. Cradle B Wall plate Plastic Face plate anchor Transmitter Outlet box Wall plate Cradle A Face plate Transmitter Wall Fig. 1 HIRO Control System Fig. 2 ©2021 Hinkley Lighting, Inc. | hinkley.com |... - Page 14 Power lead to the fan is connected to the remaining switch lead. (Fig. 4) Attach the cradle A to the wall switch box using the supplied hardware. Attach the multi-gang faceplate to the switch set in the wall outlet box. Cradle A of Hinkley switch will fit in any standard decora face plate.
- Page 15 NOTE: A single fan can be controlled with as many as 3 wall controls in one room. Every control will need to repeat the pairing process based on instructions above and all controls must be within 30 feet of the fan. ©2021 Hinkley Lighting, Inc. | hinkley.com |...
- Page 16 An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 4. This allows you to set your heating unit on a cooler setting without affecting your comfort. SUMMER MODE WINTER MODE (COUNTERCLOCKWISE DIRECTION) (CLOCKWISE DIRECTION) Fig. 3 Fig. 4 | hinkley.com...
-
Page 17: Care And Cleaning
If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation. Check to assure all dowrods to motor hardware and/or hanger ball are tight. Make sure ceiling box is secure. ©2021 Hinkley Lighting, Inc. | hinkley.com |... -
Page 18: Energy Guide
• Your cost depends on rates and use • Energy Use: 21 Watts RPMs All estimates based on typical use, excluding lights ftc.gov/energy Airflow Shown Is a Weighted Average of High and Low Cubic Feet per Minute Based on Close to Ceiling | hinkley.com... -
Page 19: Smart By Bond
Wait 10 seconds. f) Hold down the Power button on the transmitter you wish to pair. In addition to the included wall control, you can control your Hinkley The fan light should flash three times and the motor spin up for fan through the Bond app. - Page 20 HINKLEY IS PROUD TO PROVIDE YOU WITH CEILING FAN PRODUCTS THAT ENHANCE YOUR SPACE WITH COMFORT, PURPOSE AND STYLE. AS A FAMILY COMPANY, WE ARE COMMITTED TO DESIGN, PERFORMANCE AND QUALITY, AND WHAT’S IMPORTANT TO YOU IS PARAMOUNT TO US.
- Page 21 GLOBAL HEADQUARTERS 33000 Pin Oak Parkway | Avon Lake, Ohio 44012 T (440) 653 5500 | F (440) 653 5555 | hinkley.com...