Summary of Contents for Kärcher HDS 4.0/32 Pe Cage
Page 1
HDS PE CAGE English Pressure Washer To locate your local Kärcher Commercial Pressure Washer Dealer nearest you, visit www.karchercommercial.com Register 9.800-103.0-V 02/27/20 your product www.kaercher.com/welcome Downloaded from ManualsNet.com search engine...
How To Use This Manual This manual contains the following sections: The SAFETY section contains important information regarding hazardous or unsafe practices of the • How to Use This Manual machine. Levels of hazards are identified that could • Safety result in product damage, personal injury, or severe •...
Safety Introduction & Safety Information Thank you for purchasing this Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer.
Safety Important Safety Information projection à hautes vitesses. Pour éviter les lésions corporelles, une protection des yeux, du WARNING: To reduce the risk of visage, des mains et des pieds doit être portée lors WARNING injury, read operating instructions de l'utilisation de cet équipement carefully before using.
Page 7
Safety area is dry before testing the spark plug or starting placer les mains ou les pieds sur des endroits non the engine. (Fire and/or explosion may occur if this isolés de la laveuse à pression au moment de is not done.) démarrer un moteur à...
Page 8
Safety WARNING: High pressure WARNING: Be extremely careful WARNING WARNING developed by these machines will when using a ladder, scaffolding cause personal injury or or any other relatively unstable equipment damage. Keep clear of location. The cleaning area should nozzle. Use caution when oper- have adequate slopes and ating.
Safety Component Identification Wand Pump Unloader Engine Float Tank Valve Burner Spray Gun Water Supply (Not Included) Adjustable Engine Fuel Thermostat Tank Burner Fuel Tank Water Inlet High Pressure Battery Box Hose Pump — Delivers a specific gpm to the high pressure High Pressure Hose —...
Operations Assembly Instructions High Pressure Nozzle Spray Wand High Pressure Hose STEP 3: Remove shipping cap and STEP 1: Attach the high pressure STEP 2: Remove Wand end and install oil dipstick. Check pump oil hose to the spray gun using teflon first place the O-ring followed by level by using dipstick or observe tape on hose threads.
Operations Battery Installation Due to Federal Regulations concerning shipment of corrosive chemicals, batteries are not shipped with this machine. DANGER/ POISON FLUSH EYES IMMEDIATELY WITH WATER SHIELD SULFURIC EYES MEDICAL ACID EXPLOSIVE CAN CAUSE HELP SPARKS GASES CAN CAUSE FLAMES BLINDNESS OR FAST SEVERE BURNS...
Operations Operating Instructions Tank Dipstick Burner Fuel Tank STEP 2: Fill gas tank and burner STEP 1: Check engine oil level. Oil level should be level with the bottom of fuel tank with proper fuel. Do not the oil filler neck. Be sure the machine is level when checking the oil level. confuse gasoline and fuel oil tanks.
Page 13
Operations On-Off Switch STEP 7: (Electric Start Models) Turn the engine STEP 6: Pull the starter grip. If the engine fails to switch to "Start" position. start after 2 pulls, squeeze the trigger gun to release pressure and repeat step. Return starter gently. After the engine warms up enough to run smoothly, move choke to run position and throttle to fast position.
Operations Detergent & General Cleaning Techniques tures. When the water reaches this temperature, the pump protector engages and cools the pump by discharging the WARNING: Some detergents may be warm water onto the ground. This thermal device prevents WARNING harmful if inhaled or ingested, internal damage to the pump.
Operations Shutting Down & Clean Up On-Off Switch STEP 3: Turn off water supply. STEP 1: Remove detergent suction STEP 2: Turn off the engine tube from container and insert into one gallon of fresh water. Open detergent metering valve. Pull trigger on spray gun and siphon water for one minute.
Maintenance Storage CAUTION: Prior to restarting, thaw out any possible ice from pressure washer hoses, spray CAUTION: Always store your pressure washer in a gun or wand. location where the temperature will not fall below 32°F (0°C). The pump in this machine is susceptible ATTENTION: Avant de redémarrer, faire fondre la to permanent damage if frozen.
Maintenance The flow of combustion and ventilating air to the burner ATTENTION: Lorsque l'appareil est utilisé dans des must not be blocked or obstructed in any manner. endroits humides ou où les températures fluctuent fortement, l'huile doit être changée The area around the pressure washer should be kept immédiatement.
Maintenance Fuel Control System Fuel Pressure Adjustment This machine utilizes a fuel solenoid valve located on To control water temperature, adjust fuel pressure by the fuel pump to control the flow of fuel to the combus- turning the regulating pressure adjusting screw tion chamber.
Maintenance Preventive Maintenance This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative main- tenance procedures will assist in preserving the performance of your equipment. Contact your dealer for mainte- nance.
Maintenance Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Faulty pressure gauge Install new gauge. Use larger supply hose; clean filter at water Insufficient water supply inlet. Match nozzle number to machine and/or Old, worn or incorrect spray nozzle replace with new nozzle. Belt slippage Tighten or replace;...
Page 21
Maintenance PROBLEM POSSIBLE CAUSE SOLUTION Flex coupling slipping on fuel pump Replace if needed. shaft or burner motor shaft Check for electrical current reaching On-Off switch defective burner assembly with burner switch on. Heavy sooting on coil and burner can cause interruption of air flow Clean as required.
Page 22
Maintenance PROBLEM POSSIBLE CAUSE SOLUTION Improper fuel or water in fuel Replace with clean and proper fuel. Low fuel pressure Increase fuel pressure. Check fuel pump pressure. Replace pump if Weak fuel pump needed. LOW WATER TEMPERATURE Fuel filter partially clogged Replace as needed.
Page 23
Maintenance PROBLEM POSSIBLE CAUSE SOLUTION OIL DRIPPING Oil seal worn Check and replace if necessary. EXCESSIVE VIBRATION IN Irregular functioning of the valves Check and replace if necessary. DELIVERY LINE Tighten all clamps. Check detergent lines for Air leak holes. Replace restrictor.
Page 24
THANK YOU! MERCI! DANKE! GRACIAS! Registrieren Sie Ihr Produkt und profitieren Sie von vielen Vorteilen. Register your product and benefit from many advantages. Enregistrez votre produit et bénéficier de nombreux avantages. Registre su producto y aproveche de muchas ventajas. www.kaercher.com/welcome Bewerten Sie Ihr Produkt und sagen Sie uns ihre Meinung.