My.PreSonus.com with any questions or comments regarding your PreSonus Eris Sub8. We appreciate the support you have shown us through the purchase of this product and are confident that you will enjoy your Eris Sub8! PreSonus Audio Electronics致力于不断改进产品,我们非常重视你的建议。我...
Page 4
Eris Sub8 beforeconnectingit.Thiswillhelpyouavoidproblemsduringinstallationandsetup. In addition to all the basic info you’ll need to connect and operate your Eris Sub8, this manual also provides several tutorials that cover subwoofer placement, connections, and calibration.
RCA inputs will sum intotheTRS connections. PowerUser Tip: Connect both the left and right inputs if you are connecting your full-range monitors to the Eris Sub8’s outputs, or if you’re running your Eris Sub8 independentlyfrom a stereosource(such asthe PreSonusMonitorStation).This will ensure that your Eris Sub8 receivesthe low-frequencycontentfrom both the left and right sides of a stereo audio signal.
AC Select Switch. The input-power voltage is set at the factory to correspondwith thecountry towhichit was shipped. Use this switch only ifyou are using your Eris Sub8 in a country that uses a different standard voltage than is used in the country where you purchased your Sub8.
响应。 Low Pass Filter. This control determines the upper end of the frequency range reproducedbytheErisSub8.IfyouhaveenabledtheonboardHighPassFilter,set theLowPassFiltercontrolto80Hz.Otherwise,settheLowPassFiltercontroltothe lowest frequency that your main monitors can reliably reproduce. Low Pass Filter. (低通滤波器) 这个控制决定了Eris Sub8 所再现的频率范围的上 限。如果你已经启用了板载高通滤波器,将低通滤波器控制设置为80Hz。否则, 将低通滤波控制设置为你的主监听器,能够再现真实的最低频率。 Hookup Diagrams 连接图 2.2.1 Basic Setup: Media Player/Mobile Device 基本设置:媒体播放器/移动设备...
Eris Sub8 Tutorials ™ Owner’sManual LevelCalibration Owner’s Manual SubwooferPlacement Tutorials 学习指南 Subwoofer Placement 低音扬声器的放置 The goal of proper subwoofer placement is to set up your system so that your subwoofer acts as a natural extension of your full-range monitors without boosting the overall bass response of yourroom or exaggerating anyonefrequency or frequency range.Because lowfrequencies arenot directional—that is,humans cannot perceivethe direction fromwhichlow frequenciesarecoming—youaren’tlimitedtoplacingitnearyourfull-range...
Page 12
便宜和免费的声压级计应用程序,适用于几乎所有类型的智能手机,以及 各种免费在线的粉红色噪声样本,可以很好地完成你的工作。 Below is a brief tutorial on how to level match your monitors: 下面是一个简短的教程,介绍如何与你的显示器进行水平匹配: 1. Connect your monitors and Eris Sub8 as shown either of the hookup diagrams in Section 2.2. 按照第2.2节中的任一连接图连接监听设备和Eris Sub8。 PowerUser Tip: If your system has an EQ in it, turn it off.Youcan EQ your complete system to taste once the levels are evenly matched.
Page 13
平设置为对你的聆听要求更舒适的电平。只要确保左边和右边的监听器设置 为相同的电平。 5. Turnyour full-range monitorsoff.If your Sub8 is connected to the Sub Out on a speaker with a dedicatedSub Out, set the input volume of your Eris Sub8 to “0”and skip to Step 7. 关闭你的全音域监听器。如果你的Sub8连接到有专用 Sub Out 的扬 声器上的 Sub Out,将Eris Sub8的输入音量设为 "0 " 并跳到步骤 7。...
Page 14
PowerUser Tip #2: The SPL figures quoted above are guidelines. When increasing the output level, the point at which your Eris Sub8 will hit 79 dB SPL can be highly dependant upon the acoustic response of the room it’s set up in. Standing waves could cause resonance around 79 dB, causing you to reach it sooner than anticipated;...
Eris Sub8 Resources ™ Owner’s Manual Technical Specifications Resources 信号源 Technical Specifications 技术规格 INPUTS 2- Balanced ¼”TRS 2- Unbalanced RCA OUTPUTS 2-Balanced ¼”TRS (full range with 80 Hz HPF option) 2-Unbalanced RCA (full range with 80 Hz HPF option) PERFORMANCE Frequency Response 30 Hz –...
Page 16
No power.First ensure that your Eris Sub8 is plugged in. If it’s connected to a powerconditioner,verify that the powerconditioner is turned on and functioning. If it is, yet there is still no power to the Sub8, contact PreSonus for a repair. No power. 首先确保你的Eris Sub8已经插上电源。如果它连接到一个电源调节器...