Specifications - Makita HM1511 Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Blows per minute
Overall length
Net weight
Safety class
Soft no-load rotation function
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
NOTE: If the actual voltage of power supply exceeds the rated voltage, the tool may not blow. In such cases,
reduce the voltage to the rated voltage by using extension cords or the like.
Intended use
The tool is intended for chiselling work in concrete,
brick, stone and asphalt as well as for driving and com-
pacting with appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-6:
Model HM1511
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 1.57 dB (A)
Model HM1501
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 2.02 dB(A)
Model HM1512
Sound pressure level (L
Sound power level (L ) : 104 dB (A)
WA
Uncertainty (K) : 1.76 dB(A)
Model HM1502
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 1.79 dB(A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
) : 85 dB (A)
pA
) : 84 dB(A)
pA
) : 84 dB(A)
pA
) : 85 dB(A)
pA
HM1511 HM1501
781 mm
19.2 kg 18.4 kg
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-6:
Model HM1511
Work mode: chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HM1501
Work mode: chiselling
Vibration emission (a
Uncertainty (K) : 1.9 m/s
Model HM1512
Work mode: chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HM1502
Work mode: chiselling
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
4 ENGLISH
HM1512 /
HM1512E
-1
1,300 min
809 mm
20.4 kg
/II
-
2
): 8.0 m/s
h, Cheq
2
2
): 15.0 m/s
h, Cheq
2
2
): 8.4 m/s
h, Cheq
2
2
): 14.6 m/s
h, Cheq
2
HM1502 /
HM1502E
19.7 kg
-