Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kasco 2400EAF
Summary of Contents for Kasco 2400EAF
- Page 1 MOVING WATER FORWARD, SINCE 1968 SURFACE AERATOR 2400EAF, 3400EAF, 4400EAF Operation & Maintenance Manual Document number 884150 Document version 2022.1.0 800 Deere Rd. Prescott, WI 54021 | sales@kascomarine.com | kascomarine.com 1/2HP-1HP AERATOR & CIRCULATOR MANUAL...
-
Page 2: Table Of Contents
2,000 38cm 3400EAF 230 / 1 / 50 3,000 45cm 4400EAF 230 / 1 / 50 4,000 49cm WIRE SIZE Cord Length 2400EAF 1.5mm² 1.5mm² 2.5mm² 2.5mm² 3400EAF 1.5mm² 1.5mm² 2.5mm² 2.5mm² 4400EAF 1.5mm² 1.5mm² 2.5mm² 4mm² 1/2HP-1HP AERATOR MANUAL... -
Page 3: Safety First
SAFETY FIRST WARNINGS: Moving Machinery Shock Hazard • NEVER enter the water with the electrical equipment connected and/or in operation. • All electrical equipment must be Ground fault/leakage current protected. Use of a Ground fault protective device (GFI, RCD, RCBB, or RCBO type device) is required as directed by local and national codes. -
Page 4: Parts Included
PARTS INCLUDED Item Description Part No� 1/4"-20 x 3-1/2" screw 251210 1/4" split lock washer 840537 1/4", 3/4" OD flat washer 251300 Float 242003 Float retaining clip 222995 Optional Bottom Screen Assembly 3/8"-16 x 2-1/2" hex head screw 820095 3/8" flat washer 462216 Bottom screen 990162... -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTIONS Align power cord with this notch Look for indicator mark Secure to top ring of cage 1/2HP-1HP AERATOR MANUAL... - Page 6 ASSEMBLY INSTRUCTIONS (CONT.) Optional: wrap mesh around bottom screen and secure with zip ties. Position the clip flanges on either side of a vertical bar 1/2HP-1HP AERATOR MANUAL...
-
Page 7: Installation Instructions
INSTALLATION INSTRUCTIONS Attach the strain relief to the line closest to the cord. Correct anchoring Incorrect anchoring Mooring lines are too short or loose between Mooring lines are proper length and taut unit and anchors. between unit and anchors (at least 3 feet from the float for every foot of water depth). -
Page 8: Maintenance Recommendations
Sacrificial Anode All Kasco units include a sacrificial anode installed on the shaft to protect against corrosion and electrolysis. Replace the anode if it is reduced to half the original size or if it is white in color. Corrosion from electrolysis most commonly occurs in saltwater or brackish water, but it is important to check the anode in all installations at least every two to three months. - Page 9 TROUBLESHOOTING TIPS ALWAYS DISCONNECT EQUIPMENT FROM ELECTRICAL SOURCE BEFORE SERVICING SERVICE SHOULD ONLY BE PERFORMED BY A QUALIFIED TECHNICIAN OR ELECTRICIAN Ground fault/earth leakage protection (RCD) tripping Typically indicates electrical current is leaking to earth (ground). • Consult a qualified service technician or electrician to address the issue. Possible causes: •...
-
Page 10: Warranty
Also, register the unit online at: www.kascomarine.com. Once the warranty coverage has been established, the unit may be sent to any Kasco authorized repair center for evaluation and repair. Please call Kasco at 715-262-4488 prior to shipping to receive any updated information or a repair form, or call to locate your nearest authorized repair center. -
Page 11: Other Repairs
Please ship according to the instructions in the previous section. Kasco does estimates on repairs at the request of the customer. The request for an estimate should be included in the letter that accompanies the returned unit and must include a daytime phone number and/or email address. -
Page 12: Repair Contact Form
REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention. Kasco Marine • Unit should be cleaned before shipping. 800 Deere Road • Kasco is NOT responsible for shipping damage accrued in Prescott, WI 54021 return shipment.