PawHut D06-095 Manual

INdbb067_UK_D06-095_D06-096
• KEEP INSTRUCTIONS FOR FUTURE USE.
• READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE OF GATE.
• KEEP SMALL PARTS AWAY FROM
CHILDREN DURING ASSEMBLY.
INSTALLING YOUR GATE
STEP 1
Locate the (4) threaded spindle rods (B).
Rotate the adjustment wheels along the
threading, eliminating the gap between
the adjustment wheel and the rubber
foot (Figure 1-1).
NOTE Figure 1-2
You may notice a slight gap
between the gate door latch and the
frame (Figure 1-2).
THIS IS NOT A DEFECT
this gate is
a pressure mounted gate and this gap
will disappear once you tighten the gate
in its opening.
DO NOT REMOVE
THE ZIP TIE UNTIL
INSTALLATION IS
COMPLETE.
(Figure 1-3)
Figure 1-3
WARNING
Children have died or been seriously injured
when gates are not securely installed.
• ALWAYS install and use gates as directed
using all required parts.
• YOU must install wall cups to keep gate in
place.Without wall cups, child can push out and
escape.
• STOP using when a child can climb over or
dislodge the gate.
• USE only with the locking mechanism securely
engaged.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Intended for use with children between 6 and
24 months. • Install according to manufacturer' s
instructions.
STEP 2
Insert the threaded spindle rods with
adjustment wheels into the hole on all
four corners of the sides of the gate.
(Figure 2-1)
Figure 1-1
Place the gate in desired opening with
the bottom close to the floor. The
distance between the bottom of the gate
1/8
and the floor should be less than
inch (Figure 2-2). Once you are satisfied
with the placement of your gate trace
the spindle rods rubber feet onto the
surface of your opening making sure
these are level (Figure 2-3). Then remove
the gate from the opening. Then screw
the 4 wall cups to the wall using the
screws (Figure 2-4), or paste the 4 wall
cups using the stickers provided (Figure
2-5).
Figure 2-3 Figure 2-4
BEFORE ASSEMBLY
A:
Gate Frame (1)
C:
Wall Cups (4)
E:
Spanner (1)
STEP 3
Insert all 4 threaded spindle rods into the wall cups (Figure 3-1).
Figure 2-1
Tighten the wheels using the spanner tool. (Figure 3-2 and Figure
3-3) Do not over tighten. It may be necessary to hold the
threaded spindle rods while rotating the adjustment wheels to
ensure that the entire unit does not rotate while installing the
gate.
NOTE
if your door latch is not properly engaging with the
receiving component, ensure that your gate is level, mounted
properly and that you have not over-tightened the adjustment
wheels.
Figure 2-2
1/8 inch
Figure 2-5
EXTENSIONS AND MAX SIZE
MODEL NO. No 6.9 in
D06-095
D06-096
B:
Threaded Spindle
Rods (4)
D:
Screws (4)
F:
Sticker (4)
With 6.9 inch
No EXTENSION
29-31 inch 36-38 inch
NOTE
The gap between the gate and the wall should not
2.5 inch
exceed more than
If the gate has been installed properly the gap
between the door latch and frame should now be
closed (Figure 3-6)
Figure 3-1
Figure 3-2
Spanner
Figure 3-4
2.5 inch
8 in 12 in MAX SIZE
29-38 in
29-58 in
With 8 inch With 12 inch
37-39 inch 41-43 inch
on either side (Figure 3-4 and 3-5)
Figure 3-6
3/64 inch
Figure 3-3
Spanner
Figure 3-5
2.5 inch