Page 18
Contents Safety Instructions Scope of Delivery Function Installation Conditions Installation Start-up Refill and Replace Filter Material Operator’s Responsibilities Troubleshooting Warranty Technical Specifications Decommissioning and Disposal Standards and Disposal Record of Product Maintenance & Repair Product Warranty Card...
Safety Instructions Personnel qualifications The installation work described in these instructions requires basic knowledge of mechanics, hydraulics and electrical systems as well as knowledge of the General safety instructions corresponding specialist terms. The product was manufactured according to all To ensure that the device is installed safely, this work recognised regulations and technical standards and must be performed only by a qualified specialist or a was in compliance with the relevant legal requirements...
Page 20
How safety instructions are displayed Product-specific safety instructions In this document safety instructions precede any sequence of actions that could cause harm to persons Electrical hazard! or damage to property. All hazard prevention measures Contact with live components must be followed. will cause electric shock.
Scope of delivery The HB WH-Filter consists of: Control valve Pressure tank, fibreglass reinforced polyester Central tube connection, installed with nozzle system Filter material GAC Bewasorb Filter material Aqasorb GXB Filter gravel, 1-2mm Outlet: Filtered water Inlet: Unfiltered water All materials used are corrosion-resistant and suitable for use in drinking water treatment.
Function During operation, water flows from top to bottom Intended use through the filter bed and impurities are filtered out The WH-Filter removes particles, chlorine, colour, smell, or absorbed. organics, iron and manganese (Fe + Mn < 1ppm). After consumption of a predefined water volume, the The filters are not suitable for oils, grease, solvents, filter is automatically backwashed at the set time.
Installation conditions Observe all applicable installation regulations and technical specifications. In some countries a system separation is necessary when installing this filter. The installation site must be protected against frost and must guarantee the protection of the filter from water splashes, solvent vapours, fuel oil, soap sud, chemicals of System Strainer...
●Flush out any dirt particles by opening the handwheel Start-up on the multi-block module. ●Connect a corrugated hose to the multiblock module outlet and the hard water inlet (9). Be sure to observe Operating the controller the arrows indicating the direction of flow. ●Connect a corrugated hose to the multiblock module inlet and form a watertight seal with the filtered water Keypad...
Page 25
Start-up backwashing ●Insert mains plug. ●Water supply must remain closed. ●The display shows StArt and then alternates between the capacity and day of the week (1-7) / time. ●Allow basic fixing to finish (approx. 40 sec.) The running StArt noise stops. ●An automatic backwashing starts.
Page 26
Setting the capacity between backwashs Press the Browse button Press the OK button 5 ..07:43 Press the down arrow buttons Press the OK button 1.800 Use the up/down arrow buttons to set the capacity (in Liters). 1.850 3.000 Press the OK button Press the Browse button The programming is complete.
Refill and replace filter material First filling and replace filter material 1.Detach hoses from control valve 2.Detach control valve from pressure tank 3.Remove the used filter material 4.Clean pressure tank and central tube with water 5.Replace central tube into pressure tank NOTE: Locate top of central tube in centric recess! 6.Cover central tube’s upper end NOTE: For refilling it is important that no filter media...
(according to EN 806 -5 by the operator) Inspection activity Interval Note for products WITHOUT Note for products WITH active BWT -DES registration active BWT-DES registration Check contamination of the filter every 2 months Required Required...
Troubleshooting Fault Cause Rectification Increase primary pressure (adjust Unit is not providing water or too pressure reducer if required) and Primary pressure too low. low a flow rate activate manual regeneration. Abrasion particles of the Dyed flushing water during the start-up. Repeat start-up flushing.
Page 30
BWT Wassertechnik GmbH Actual Production Induster iestrasse 7, D-69198 Schr ieshe im Address Responsible BWT Haier Drinking Water Technology Co., Ltd Company in China Qingdao Sino-German Eco Park, Beta Space, Room 216,172 Taibaishan Rd., Address Huangdao District, Qingdao, Shandong, China...
Decommissioning and disposal Standards and legal provisions ●Standards and legal provisions shall always be applied in Decommissioning the most recent version. ●The following must be observed when installing and The product may only be shut down and dismantled by operating the filter: qualified specialists.
Record of Product Maintenance & Repair Product type: Purchase date: Record of Product Maintenance Maintenance Date Maintenance Content Service Person Signature In order to ensure the product can be operated properly and filter out high-quality purified water, please carefully read the instruction manual and replace the filter material on time. Record of Product Repair Maintenance Date Maintenance Content...
Product Warranty Card Thank you so much for purchasing Haier BWT inside products! If the products purchased through regular channels are non-artificially damaged, we will provide a 2-year free warranty service from the date of installation. Acknowledgement of Receipt (Distributor’s) For installation, please call the service hotline: Card no.:...
Page 34
CERTIFICATE OF INSPECTION 倍世饮水设备有限公司 Add:中国青岛海尔路1号(海尔工业园) T e l :400-895-9910...