Connecting To Various Devices; Signals That Can Be Input To The Projector - JVC DLA-G150CLU Operating Instructions Manual

Connecting to Various Devices

Before connection, be sure to turn off the projector and connected devices.
Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:
Video signals
(1) Response to color systems
Color systems
NTSC NTSC4.43
Input terminal
‡
VIDEO
‡
Y/C
‡*
2
Y, P /B-Y, P /R-Y
B R
‡*
2
G, B, R, H/C , V
S
*1:Responds if Y/C output is available.
*2:Signifies that component signals ("Y, P , P " / "Y, B-Y, R-Y" / "G, B, R, H/C
B R
(synchronization and video period) of each color system. The color systems are used for convenience only.
(2) Response to double density (*3), high-vision signals
4
Input terminal NTSC*
‡
Y, P /B-Y, P /R-Y
B R
‡
G, B, R, H/C , V
S
*3:Signals whose density of scanning lines/field is twice as high.
*4:Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line
doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded
wide-clear-vision signal and decoded 525P progressive signal.
*5:Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler
(separately available: recommended article).
(3) Response to DTV-format signals
DTV-format signals (480i, 480p, 720p, 1080i) can be input to the Y, P
Computer signals
Signals with the following scanning frequencies can be input to the PC 1 or PC 2 (G, B, R, H/C
Horizontal scanning frequency 15kHz - 105kHz
Vertical scanning frequency 50Hz - 100Hz
Be sure that the computer to be used suffices the following conditions:
• The computer has the video signal output port.
Be sure that the computer has the video signal output port by reading the instruction book of the computer.
The video signal output port is generally called as "RGB port", "monitor port", or "video port". If the computer-monitor hybrid
type or note type is used, it may need to prepare for an external output port. Also, there will be the type to which an external
output port cannot be installed.
• DVI input
During DVI input, depending on the computer settings, there may be no signal input or an error may occur (blue screen).
If this happens, turn off the power to both the projector and the computer, and then turn the projector back on before turning
the computer on again. Then correctly set the computer's graphic board.
• The resolution and the scanning frequencies are within the range specified in the table on page 23.
Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of range
cannot be used. (Even signals out of the range could be projected. However, it may not sharp enough. On the other hand,
even some of the signals within the range may require adjustment depending on the video board used.)
When a signal other than listed in the table on page 23 is input, the image could be partially erased or an unneeded fold-over
image could appear.
Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
Composite sync (C ) and G on Sync signals cannot be handled depending on the devices connected.
S
22
All manuals and user guides at all-guides.com
PAL SECAM
‡ ‡ ‡
‡* ‡
1 - - - - -
‡* ‡* ‡*
2 2 2
‡* ‡* ‡*
2 2 2
, V") conform to the signal timing
S
5
NTSC* High-vision signal
‡ ‡
‡ ‡
/B-Y, P /R-Y, G, B, R, H/C , V input terminal.
B R S
, V) and DVI terminals.
S
Allowable input signals
Horizontal res-
Signal olution
Hor [Pixels]
PC system PC98 VESA350
PC/AT PC98
DOS/V VGA 60Hz*
DVI* VGA 72Hz*
VGA 75Hz*
VGA 85Hz*
SVGA 56Hz*
SVGA 60Hz*
SVGA 72Hz*
SVGA 75Hz*
SVGA 85Hz*
XGA 43Hz*
XGA 60Hz*
XGA 70Hz*
XGA 75Hz*
XGA 85Hz*
SXGA 43Hz*
SXGA 60Hz*
SXGA 75Hz*
SXGA 85Hz*
UXGA 60Hz
Mac MAC13
MAC16
MAC19
MAC21
Video system Video HDTV (1035i) 60Hz
HDTV (1035i) 59Hz
480p
720p 60Hz
720p 59Hz
1080i 60Hz
1080i 59Hz
1080 24sF
NTSC
PAL
SECAM
* A signal that can be input by DVI (V-sync 85Hz is not supported.)
Notes
• The resolution for the input signals is listed in the above table.
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
• When a signal other than listed above is input, the image could be partially erased or an unneeded fold-over image could
appear.
• Some signals other than listed above can be displayed. But they may require adjustment.
• Even some of the signals listed above may require adjustment depending on the video board used.
• Composite sync (C ) and G on Sync signals cannot be handled depending on the devices connected.
S
• The VGA signal of the PC system could be displayed in 480p mode of the VIDEO system. (In this case, the projector enters
video menu mode when the MENU button is pressed.)
Connecting to Various Devices
Vertical resolu- Horizontal fre- Vertical fre-
tion quency quency
Ver [Lines] H [kHz] V [Hz]
640 350 37.86 84.13
640 400 24.83 56.42
640 480 31.47 59.94
640 480 37.86 72.81
640 480 37.50 75.00
640 480 43.27 85.01
800 600 35.16 56.25
800 600 37.88 60.32
800 600 48.08 72.19
800 600 46.88 75.00
800 600 53.67 85.06
1024 768/2 35.52 43.48
1024 768 48.36 60.00
1024 768 56.48 70.07
1024 768 60.02 75.03
1024 768 68.68 85.00
1280 1024/2 46.43 43.44
1280 1024 63.98 60.02
1280 1024 79.98 75.03
1280 1024 91.15 85.02
1600 1200 75.00 60.00
640 480 35.00 66.67
832 624 49.73 74.55
1024 768 60.24 74.93
1152 870 68.68 75.06
33.75 60.00
33.72 59.94
720 483 31.47 59.94
1280 720 45.00 60.00
1280 720 44.96 59.94
1920 1080/2 33.75 60.00
1920 1080/2 33.72 59.94
1920 1080 27.00 24.00
15.734 60
15.625 50
15.625 50
23