Features And Controls - DeWalt DCS727T2 Manual

English
Changing or Installing a New Saw Blade
Removing the Blade (Fig. H1–H4)

WARNING: To reduce the risk of injury, wear gloves when handling
the saw blade.

WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start‑up can cause injury.
• Never depress the spindle lock button while the blade is under
power or coasting.
• Do not cut light alloy and ferrous metal (containing iron or steel)
or masonry or fibre cement product with this mitre saw.
1. Remove the battery from the saw.
2. Raise the arm to the upper position and raise the lower guard
as possible.
3. Depress the spindle lock button
blade by hand until the lock engages.
4. Keeping the button depressed, use the other hand and the 6 mm
wrench provided 31 to loosen the blade screw
left‑hand threads.)
5. Remove the blade screw 43
The inner washer 48 may be left on the spindle.
6. Remove and retain the adaptor ring
needed when installing a new blade.
Installing a Blade (Fig. H1–H4)
1. Remove the battery from the saw.
2. Snap the ring adaptor ring
if necessary.
3. With the arm raised and the lower guard
onto the shoulder of the inner washer
bottom of the blade point toward the back of the saw.
4. Assemble the outer clamp washer onto the spindle.
5. Install the blade screw and, engaging the spindle lock, tighten
the screw firmly with wrench provided (turn counterclockwise,
left‑hand threads).

WARNING! Be aware the saw blade shall be replaced in the described
way only. Only use saw blades as specified under Technical Data;
Cat. no.: DT4260 is suggested.
Transporting the Saw (Fig. A1, A2)

WARNING: To reduce the risk of serious personal injury,
ALWAYS lock the rail lock knob, mitre lock handle, bevel lock handle,
lock down pin and fence adjustment knobs before transporting saw.
Never use guards for transporting or lifting up.
In order to conveniently carry the mitre saw, a carrying handle
included on the top of the saw arm.
• To transport the saw, lower the head and depress the lock down
pin 11 .
• Lock the rail lock knob with the saw head in the front position, lock the
mitre arm in the full left mitre angle, slide the fence
inward and lock the bevel lock knob
vertical position to make the tool as compact as possible.
• Always use the carrying handle

Features and Controls


WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start‑up can cause injury..
44 while carefully rotating the saw
43 . (Turn clockwise,
, outer clamp washer 45 and blade
47 from the old blade in case it is
47 into the hole of the new saw blade
1 held open, mount the blade
48 , making sure the teeth at the
13 completely
33 with the saw head in the
3
or the base extensions
Mitre Control (Fig. A2, I)
The mitre lock handle
your saw to 60 ° right and 50 ° left. To mitre the saw, lift the mitre lock
handle, push the mitre latch button and set the mitre angle desired on the
mitre scale 19
Override the mitre latch button by unlocking the mitre lock knob and
pushing the mitre detent override
the mitre detent override upward.
Bevel Lock Knob (Fig. A2)
The bevel lock allows you to bevel the saw 49 ° left or right. To adjust the
bevel setting, turn the bevel lock knob
bevels easily to the left or to the right once the 0 ° bevel override knob is
pulled. To tighten, turn the bevel lock knob clockwise.
0 ° Bevel Override (Fig. A2)
1 as far
The 0 ° bevel stop
the 0 ° mark.
When engaged, the saw will automatically stop at 0 ° when brought up
from the left. To temporarily move past 0 ° to the right, pull the bevel lock
knob 33 . Once the knob is released, the override will be reengaged. The
bevel lock knob can be locked out by twisting the knob 180 °.
When at 0 °, the override locks in place. To operate the override, bevel the
46 .
saw slightly to the left.
45 ° Bevel Stop Override (Fig. J)
There are two bevel stop override levers, one on each side of the saw.
To bevel the saw, left or right, past 45 °, push the 45 ° bevel override
55
lever rearward. When in the rearward position, the saw can bevel past
these stops. When the 45 ° stops are needed, pull the 45 ° bevel override
lever forward.
Crown Bevel Pawls (Fig. J)
When cutting crown molding laying flat, your saw is equipped to accurately
and rapidly set a crown stop, left or right (refer to Instructions for Cutting
Crown Molding Laying Flat and Using the Compound Features)
The crown bevel pawl
adjustment screw.
To reverse the crown bevel pawl, remove the retaining screw, the 22.5 °
bevel pawl 56
pawl 57 so the 30 ° text is facing up. Reattach the screw to secure the
22.5 ° bevel pawl and the crown bevel pawl. The accuracy setting will not
be affected.
22.5 ° Bevel Pawls (Fig. J)
Your saw is equipped to rapidly and accurately set a 22.5 ° bevel, left
or right. The 22.5 ° bevel pawl
adjustment screw
Rail Lock Knob (Fig. A1)
3 has been
The rail lock knob
sliding on the rails
transporting the saw.
Grooving Stop (Fig. A2)
The grooving stop
The stop is useful for applications such as grooving and tall vertical cuts.
Rotate the grooving stop forward and adjust the depth adjustment
screw 29 to set the desired depth of cut. To secure the adjustment, tighten
15
.
the wing nut
bypass the grooving stop feature. If the depth adjustment screw is too tight
to loosen by hand, the provided 6 mm blade wrench
loosen the screw.
Lock Down Pin (Fig. A1)

WARNING: The lock down pin should be used only when
carrying or storing the saw. NEVER use the lock down pin for any
cutting operation.
21 and mitre latch button
. Push down on the mitre lock handle to lock the mitre angle.
38 downward. To exit the override, push
33 counterclockwise. The saw head
34 override allows you to bevel the saw to the right past
57 can be rotated to contact the crown
and the 30 ° crown bevel pawl
56 can be rotated to contact the crown
54 .
6 allows you to lock the saw head firmly to keep it from
9 . This is necessary when making certain cuts or when
30 allows the depth of cut of the blade to be limited.
28 . Rotating the grooving stop to the rear of the saw will
22 allow you to mitre
57 . Flip the crown bevel
31 can be used to