Directed Directechs HYUNDAI8 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. Directechs HYUNDAI8
  6. Installation manual
Directed Directechs HYUNDAI8 Installation Manual

Directed Directechs HYUNDAI8 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
HYUNDAI8
Designed by Installers for Installers
© 2016 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2016-12-02
Directed Digital
Solutions

Advertisement

Table of Contents
loading

Related Manuals for Directed Directechs HYUNDAI8

Summary of Contents for Directed Directechs HYUNDAI8

  • Page 1 HYUNDAI8 Designed by Installers for Installers © 2016 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Introduction The HYUNDAI8 firmware for Directed Digital Solutions is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific Hyundai vehicles. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for smartphones.

  • Page 5: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 6: Wiring Connections

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 7: Analog Harness (H3), 18-Pin White Connector

    These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle wiring reference chart" on page 11 for a list of compatible features. Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)

    4: Yellow/Red: Smart Key. Interrupt (veh. side) Siren Smart Key Interrupt: Pink/Orange: pin 20 I/P-G Back Fusebox (white 40-pin connector) Directed Digital Solutions HYUNDAI8 All connectors are displayed from the wire side (unless specified otherwise). © 2016-12-02 Directed. All rights reserved.
  • Page 9 OBDII connector. Black B-CAN High Yellow Data Driver Kick MF11 connector. White B-CAN Low Black Data Driver Kick MF11 connector. White Locating components in the vehicle MF11 (77-WHT) EM11 (47-WHT) Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 10: Type 2

    MF11 Drivers Kick Panel Junction (white 68-pin connector) Smart Key Interrupt: Pink/Orange: pin 20 I/P-G Back of Fusebox (white 40-pin connector) All connectors are displayed from the wire side (unless specified otherwise). Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.
  • Page 11 White Data OBDII connector. Black C-CAN Low Brown Data OBDII connector. Black B-CAN High Yellow Data Driver Kick MF11 connector. White B-CAN Low Black Data Driver Kick MF11 connector. White Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.
  • Page 12 Locating components in the vehicle Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 13: Type 3

    (+) Siren Output: Brown: 17 5: Orange/Red: Smart Key Interrupt (conn. side) 4: Yellow/Red: Smart Key. Interrupt (veh. side) Siren All connectors are displayed from the wire side (unless specified otherwise). Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.
  • Page 14 C-CAN Low Yellow Data OBDII connector. Black B-CAN High White Data Rear Fusebox I/P-F connector. White B-CAN Low Brown Data Rear Fusebox I/P-F connector. White Locating components in the vehicle Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 15: Connecting The Module

    Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected.

  • Page 16: Rf Systems

    When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination.

  • Page 17: Module Programming

    Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red.

  • Page 18: Led Diagnostics And Troubleshooting

    The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to MUX not detected. "Installation (wiring diagrams & vehicle wiring reference charts)" on page 8 to check the Flashes red x 7 connections. Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.
  • Page 19 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 20: Soft Reset

    A module reset will only erase the steps performed in "Module programming" on page 17. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the Directed Digital Solutions, 12-pin harness EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module.

  • Page 21: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital Solutions HYUNDAI8 © 2016-12-02 Directed. All rights reserved.

  • Page 22: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 23: Quick Reference Guide

    Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode.
  • Page 24 SmartStart compatible Notes This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your smartphone;...

Table of Contents