Summary of Contents for Horizon Hobby Axial FORD BRONCO
Page 1
AXI00006T1/T2 FORD BRONCO INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI...
Page 2
This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.
WET CONDITIONS MAINTENANCE • Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed. CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique.
• Always disconnect the battery after charging, and let the charger cool between charges. • Always charge in a well-ventilated area. • Always terminate all processes and contact Horizon Hobby if the product malfunctions. • Charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
TRANSMITTER LAYOUT Use the diagram below to familiarize yourself with the different parts of your transmitter. The transmitter antenna is mounted internally and is located in the front portion of the transmitter. When you are driving your model, hold the transmitter so it is oriented as close to vertical as possible. Do not try to follow your model with the transmitter.
INSTALL THE TRANSMITTER BATTERIES 1. Open the battery compartment cover. 2. Install 4 AA alkaline batteries, verifying correct polarity. 3. Close the battery cover. CAUTION: NEVER remove the transmitter batteries while the vehicle is powered ON. Loss of vehicle control, damage, or injury may occur.
POWER ON THE VEHICLE TEST THE CONTROLS With the vehicle wheels off the ground, test the throttle and steering controls. Ensure the wheels spin in the proper direction and the front wheels turn in the proper direction with steering input. After checking for proper direction of controls, start driving slowly.
AFTER DRIVING When you are finished driving your vehicle: 1. Power off the vehicle. 2. Power off the transmitter. 3. Remove the vehicle battery and charge if necessary. ST. REV TH. REV BINDING THE TRANSMITTER AND RECEIVER Binding is the process of programming the receiver to recognize a specific transmitter signal, thus preventing interference from other transmitters.
Product, (iv) attempted remedy shall be that Horizon will, at its option, either (i) service by anyone other than a Horizon Hobby authorized service, or (ii) replace, any Product determined by Horizon service center, (v) Product not purchased from an authorized to be defective.
Page 12
Limitation of Liability is available at http://www.horizonhobby.com/content/ service-center_render-service-center. If you do not have HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, internet access, please contact Horizon Product Support INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF to obtain a RMA number along with instructions for PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN submitting your product for service.
If this equipment does cause Supplier’s Declaration of Conformity harmful interference to radio or television reception, Axial Ford Bronco 1/24th Scale 4WD RTR which can be determined by turning the equipment (AXI00006T1/T2) off and on, the user is encouraged to try to correct the...
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION EU Compliance Statement: Axial Ford Bronco 1/24th Scale 4WD EU Manufacturer of Record: RTR (AXI00006T1/T2); Hereby, Horizon Horizon Hobby, LLC Hobby, LLC declares that the device is in compliance with 2904 Research Road the following: EU Low Voltage Directive 2014/35/EU; EU Champaign, IL 61822 USA EMC Directive 2014/30/EU;...
Page 17
AXI204000 SCX24 Suspension Links (long) SCX24 Aufhängeglieder (lang) Bras de suspension SCX24 (long) SCX24 Bielle sospensioni (lunghe)
Page 18
AXI31614 SCX24 Chassis Set SCX24 Karosseriesatz Ensemble de carrosserie SCX24 SCX24 Set telaio AXI31611 AXI31611 AXI31608 AXI31619 AXI31610 AXI31609 HRZ00015 AXI204000 DYNB0012 AXI31612...
Page 19
AXI200009 SCX24 Ford Bronco Body, White SCX24 Ford Bronco Karosserie, Weiß Carrosserie de SCX24 Ford Bronco, blanc SCX24 Ford Bronco carrozzeria, bianco AXI200011 AXI40004 AXI40006...
Need help?
Do you have a question about the Axial FORD BRONCO and is the answer not in the manual?
Questions and answers