Page 1
AXI03006 T1/T2 INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI...
Page 2
Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Notes ........................ 60 WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS Your new Horizon Hobby vehicle has been designed and built with • Even minimal water contact can reduce the life of your motor if it a combination of waterproof and water-resistant components to has not been certifi...
GETTING STARTED CHECKLIST Read the manual Power on the transmitter Familiarize yourself with the vehicle and its components Install the vehicle battery in the vehicle Check all screws, especially the driveshaft setscrews, for Check for proper function of the throttle and steering tightness from the factory Range check the radio system Charge the vehicle battery...
CHARGE THE VEHICLE BATTERY Follow the manufacturer’s directions for your charger to properly charge the vehicle battery. CAUTION: Only use chargers designed to charge the chosen battery type. Using an incorrect charger or incorrect charger settings could cause the battery to catch fi re or explode. INSTALL THE TRANSMITTER BATTERIES This transmitter requires 4 AA batteries.
ADJUSTING THE VEHICLE BATTERY TRAY The battery trays may be adjusted to fi t a wide range of battery sizes. The rear battery tray is shown in the illustration. The side battery tray is adjustable in the same manner. To adjust the battery tray: 1.
BINDING Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifi er) code of a single specifi c transmitter. The transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below. 1.
VEHICLE MAINTENANCE Just like a full size car or truck your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle. Replace any Check for wear on Check driveshaft...
SPEKTRUM RECEIVER/ESC COMBO OPERATION SPECIFICATIONS 1. Power on the transmitter. Waterproof DSMR ESC/Receiver 2. Power on the receiver. Type 2-in-1 with SMART Telemetry 3. The green LED on the receiver will be illuminated when it is Dimensions (L × W × H) 54mm ×...
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Your transmitter and receiver are too Move transmitter 8 to 12 feet away from receiver close together You are near metal objects Move to an area with less metal The receiver is bound to a different Make sure the correct model memory is active in your The system will not connect model memory...
Product Support Inquiry, or call the toll free telephone number Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the referenced in the Warranty and Service Contact Information section to product purchased (the “Product”) will be free from defects in materials...
EU COMPLIANCE STATEMENT: Axial SCX10 III Jeep Gladiator (AXI03006) Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED Directive. A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
PARTS LISTS // TEILELISTEN // LISTE DES PIÈCES // ELENCO COMPONENTI Part # Description Beschreibung Description Descrizione Paraurti anteriore e posteriore AXI230018 CRC JL Front & Rear Bumper CRC JL Front- und Heckstoßstange Pare-chocs avant et arrière CRC JL CRC JL Kühler und vorderer Kotfl...
Page 22
Part # Description Beschreibung Description Descrizione Engrenages d’entraînement Ingranaggi interni trasmissione AXI232031 Internal Metal Drive Gears Interne Metall-Antriebszahnräder métalliques internes in metallo Engrenages métalliques de boîte de Ingranaggi in metallo custodia di AXI232032 Transfer Case Metal Gears Transfergehäuse Metallgetriebe transfert trasferimento Metallgetriebe Eingabe 27T, 20T Engrenages métalliques d’entrée...
Page 23
Part # Description Beschreibung Description Descrizione Vis d’assemblage creuse, M2,5 x Vite a testa cilindrica M2,5 x AXI235230 M2.5 x 18mm Cap Head Screw (10) Inbusschraube, M2,5 x 18mm (10) 18mm (10) 18mm (10) AXI236172 Screw Shaft M3 x 2.0 x 12mm (10) Schraubenschaft M3 x 2 x 12mm Tige de vis M3 x 2 x 12mm Albero fi...
OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES FACULTATIVES // PARTI OPZIONALI Part # Description Beschreibung Description Descrizione Universal-Gehäusestangensatz: Ensemble poteau de carrosserie AXI230025 Uni Body Post Set: SCX10 III Set supporti scocca uni: SCX10 III SCX10 III universel : SCX10 III Renvoi de commande de servo, Squadretta servo, metallo 25T: AXI231013 Servo Horn, Metal 25T: SCX10III...
Need help?
Do you have a question about the AXI03006 and is the answer not in the manual?
Questions and answers