Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CDA EVC41SS
Summary of Contents for CDA EVC41SS
- Page 1 EVC41 Cylinder Extractor Installation, use and maintenance www.cda.eu...
-
Page 2: Table Of Contents
Contents: Important Important information Using your extractor Timer function Clean air function Care and maintenance Removing the grease filter Changing/fitting the charcoal filter(s) Changing the light 11 - 15 Installation Installation preparation - height Ducting and ventilation Mounting the extractor Mains electricity connection Electrical information 17 - 18... -
Page 3: Important
Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model... -
Page 4: Important Information
and requirements of EU Directive 2014/30/EU (EMC). IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. - Page 5 • This extractor has been designed to be used in a room with a volume of less than 36m3. • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors.
-
Page 6: Using Your Extractor
Using your extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking (you can use the timer function, detailed on page 7, for this). Control Panel (Fig. - Page 7 To activate the timer function • Press and hold the desired speed button for approximately 5 seconds to activate a 15 minute timer for that speed. The selected speed’s indicator should flash. Hold the same button for approximately 5 seconds to cancel the timer. Please note that the intensive speed automatically switches off after approximately 6 minutes (see page 18 for more information).
-
Page 8: Care And Maintenance
Care and maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. - Page 9 Please note: After 30 hours of use the light button will flash to signal that the filter needs to be cleaned. With the extractor off, press and hold the lamp button until it stops flashing to reset after cleaning. To remove the grease filter, lift the catch on the handle on the grease filter.
-
Page 10: Changing The Light
Changing the light bulbs If one or more of your LED units fail, please contact CDA Customer Care using the contact details below to arrange a service visit. Contact CDA Customer Care A: Customer Care Department, The CDA Group Ltd, Harby Road,... -
Page 11: Installation
Installation When installing this product we recommend you seek the help of another individual. This product may have some sharp edges. Please take care and wear adequate PPE when handling. Installation preparation - height When the extractor is to be installed above an electric hob, the minimum distance between the hob and the bottom edge of the extractor must exceed 650mm. - Page 12 There are images below showing the extractor dimensions (Fig. 3) and mounting hole positions (Fig. 4). These are intended to help with preparation for installing the extractor. 128.5 Fig. 3 Fig. 4 Taking into account the extractor dimensions, and the advice regarding installation height as per page 11, roughly mark the screw hole positions ‘A’...
-
Page 13: Ducting And Ventilation
Ducting and ventilation For best performance and lowest noise output, we recommend the use of 150mm ducting. You can also use smaller diameter ducting but this will reduce performance and potentially increase the noise level of the extractor whilst in use. In general, the less ducting you use (i.e. distance and bends) the more efficient your extractor will be. -
Page 14: Mounting The Extractor
Mounting the extractor If space will be tight once the extractor body has been mounted, remove the chimney piece and then remove the film protecting it. Place the chimney piece back inside the extractor body, whilst taking care not to scratch it. If you can leave this stage until last, then do so as it will help to prevent the chimney piece from receiving damage. - Page 15 If you have not already done so (see beginning of page 14), remove the chimney piece and peel off the protective film. Carefully place the chimney piece back inside the extractor body and then attach it to the chimney piece fixing bracket via the pre-drilled holes in the chimney piece (Fig.
-
Page 16: Mains Electricity Connection
Mains electricity connection THIS APPLIANCE COMES WITH A 3A PLUG BUT CAN BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. DOUBLE POLE We recommend that the appliance is SWITCHED FUSED SPUR OUTLET... -
Page 17: Electrical Information
Check that the mains supply has not been switched off. Check whether the extractor still extracts on any speed. If not, check the fuse, as above. If the lights still do not work, contact CDA Customer Care using the details on page 18. (continued on page 18) - Page 18 Press and hold the light button to reset after cleaning. If any of the potential resolutions in this guide do not resolve your issue, please contact CDA Customer Care using the contact details below. Contact CDA Customer Care...
-
Page 19: Energy Efficiency Information
Measured power consumption in 0.45 standby mode Sound power level 90 (B) Hood c i f 44 (A) Hood E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the right to change specifications without prior notice. - Page 20 For more information please contact: The Sales Department on 01949 862 010 or email sales@cda.eu Customer Care Department. The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY 01949 862 012 F: 01949 862 003 E: customer.care@cda.eu www.cda.eu...