Stanley FatMax SFMCD720B-XJ Manual page 9

To install battery pack (Fig. C)
Insert battery pack firmly into tool until an audible click is
u
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (7b) as shown in
u
figure D and pull battery pack out of tool.
Belt hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal injury,
place the forward/reverse button in the lock-off position or
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Warning! To reduce the risk of serious personal injury, ONLY
use the tool's belt hook (9) to hang the tool from a work belt.
DO NOT use the belt hook (9) for tethering or securing the
tool to a person or object during use. DO NOT suspend tool
overhead or suspend objects from the belt hook.
Warning! To reduce the risk of serious personal injury, ensure
the screw (10) holding the belt hook is secure.
Note: When attaching or replacing the belt hook (9), use only
the screw (10) that is provided. Be sure to securely tighten
the screw.
The belt hook (9) can be be attached by sliding into the
slots (11) on either side of the tool using only the screw (10)
provided, to accommodate left- or right- handed users. If the
hook is not desired at all, it can be removed from the tool.
To move the belt hook, remove the screw (10) that holds the
belt hook (9) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (10).
Note: Various trackwall hooks and storage configurations
are available.
Please visit our website www.stanley.eu/3 for
further information.
Keyless chuck (Fig. G)
Warning! Make certain the battery pack is removed to prevent
tool actuation before installing or removing accessories.
To insert a drill bit or other accessory:
Grasp the chuck (4) and rotate it in the counterclockwise
u
direction, as viewed from the chuck end.
Insert the bit or other accessory (12) fully into the chuck
u
and tighten securely by rotating the chuck in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten or loosen drill bits (or any
other accessory) by gripping the front part of the chuck and
turning the tool on.
Damage to the chuck and personal injury may occur when
changing accessories.
(Original instructions)
Trigger switch & forward/reverse button (Fig H)
The drill is turned ON and OFF by pulling and releasing
u
the trigger switch (1) shown in figure H. The farther the
trigger is depressed, the higher the speed of the drill.
A forward/reverse control button (2) determines the
u
rotational direction of the tool and also serves as a lock
off button.
To select forward rotation, release the trigger switch and
u
depress the forward/reverse control button on the right
side of the tool.
To select reverse, depress the forward/reverse control
u
button on the left side of the tool.
The centre position of the control button locks the tool in
u
the off position. When changing the position of the control
button, be sure the trigger is released.
Adjusting torque control (Fig I)
This tool is fitted with a torque adjustment collar (3) to select
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials
require a higher torque setting than small screws and soft
workpiece materials.
For drilling in wood, metal and plastics, set the collar (3) to
u
the drilling position symbol.
For screwdriving, set the collar to the desired setting. If
u
you do not yet know the appropriate setting, proceed as
follows:
Set the collar to the lowest torque setting.
u
Tighten the first screw.
u
If the clutch ratchets before the desired result is
u
achieved, increase the collar setting and continue
tightening the screw.
Repeat until you reach the correct setting.
u
Use this setting for the remaining screws.
u
Speed selector switch (Fig J)
The dual range feature of your drill allows you to shift gears
for greater versatility.
To select low speed, high torque setting (position1), turn
u
tool off and permit to stop. Slide gear shifter button (5)
away from the chuck.
To select the high speed, low torque setting (position 2),
u
turn tool off and permit to stop. Slide gear shifter button
back toward the chuck.
Note: Do not change gears when tool is running. If you are
having trouble changing gears, make sure that the dual range
gear button is either completely pushed forward or completely
pushed back.
ENGLISH
9