Related Manuals for Omega OS880 Series
Summary of Contents for Omega OS880 Series
- Page 1 U ser’ s Gui d e Shop online omega.com e-mail: info@omega.com For latest product manuals: www.omegamanual.info OS880 Series Essential Handheld Infrared Thermometer...
- Page 2 Engineering Service: 1-800-872-9436 (USA & Canada only) Tel: (203) 359-1660 Fax: (203) 359-7700 e-mail: info@omega.com The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains and reserves the right to alter specifications without notice.
-
Page 3: Table Of Contents
Table of Contents Table of Contents ............................. 3 1) Introduction .............................. 4 1.1 How it works .................................4 1.2 Caution .................................5 2) Specifications ............................6 3) Operating Instructions ..........................6 3.1 Battery Installation: ...............................6 3.2 Button and key Layout: ............................7 3.3 Locating a Hotspot: ..............................8 4) Maintenance ............................. -
Page 4: Introduction
Introduction The OS880-Series handheld infrared thermometer is a non-contact temperature sensing thermometer. It measures from -30 to 550°C (-22 to 1022°F). This thermometer features a backlit display which is automatically illuminated when the trigger is pulled and allows working in poor or zero-lighting conditions. The single laser is also automatically active when the trigger is pulled. -
Page 5: Caution
Emissivity Table: Material Emissivity Material Emissivity Aluminum 0.30 Iron 0.70 Asbestos 0.95 Lead 0.50 Asphalt 0.95 Limestone 0.98 Basalt 0.70 0.94 Brass 0.50 Paint 0.93 Brick 0.90 Paper 0.95 Carbon 0.85 Plastic 0.95 Ceramic 0.95 Rubber 0.95 Concrete 0.95 Sand 0.90 Copper 0.95... -
Page 6: Specifications
Specifications Temperature Range -30 to 550°C (-22 to 1022°F) Accuracy ±3°C or ±3% of rdg, -30°C to 0°C (-22 to 32°F) ±2°C or ±2% of rdg, 0°C to 100°C (32 to 212°F) ±3°C or ±3% of rdg, ≥100°C (212°F) Field of View 12:1 Repeatability 1% of reading or... -
Page 7: Button And Key Layout
Operating instructions 3.2 Button and key Layout: [Grab 1) Trigger 2) Back light/Up Button 3) Mode button 4) T/Down Button 5) SET Button 6) LCD Display 7) Battery Door 8) Laser Button 3.3 Operating Steps 1) Hold the thermometer by the handle grip and point it towards the surface to be measured. 2) Pull and hold the trigger to turn the thermometer on. -
Page 8: Locating A Hotspot
3.4.3 Adjusting Laser 1) While holding the trigger and “SCAN” activated on display, press the “Laser” button [8] to toggle the single laser dot on and off. 3.4.4 Adjusting Emissivity 1) With unit turned “on”, press the “MODE” button [3] a few times to get to the “Є” annunciator which will show the current Emissivity value. - Page 9 Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
- Page 10 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References ...