General Information; Installation - Ariston SG1 Series User Manual

KEY TO SYMBOLS
Congratulations on your purchase of an electric water heater manufactured by Ariston Thermo Group. The appliance
is designed in compliance with the European quality standards and conforms to declared technical characteristics. The
Symbol
water heater is easy to use; it demonstrates great consumer properties and durability in operation. We hope that you will
be satisfied with its work.
Please, read this manual carefully to ensure proper installation and operation of the water heater.
Failure to comply with this requirement can result in severe injuries and even death

1. GENERAL INFORMATION

Failure to comply with this requirement can result in damage to property, plants, or animals
1.1. Delivery set and purpose
1.1.1. Water heater
1.1.2. Safety valve
General requirements and safety precautions for use
1.1.3. Bracket
1.1.4. Installation and operation manual
GENERAL SAFETY NORMS
1.1.5. Warranty certificate
1.1.6. Original packing
Ref.
The appliance is designed for installation inside the buildings, in the household and utility premises. It is intended for water
heating to a temperature below boiling point, with the option of the hot hot water's supply (not intended for drinking) at
several spots (bathroom, kitchen, and toilet) and further maintenance of the set temperature in the automatic mode.
1
Water heating time depends on the volume of the water heater and the power of the heating element.
Do not open the water heater body
1.2. Main elements
1.2.1. Inner tank
1.2.2. Thermal insulation of polyurethane foam providing minimal heat dispersion
Do not start or stop the water heater by plugging it into or out of
2
1.2.3. Heating element
the wall outlet. Use the power switch for this purpose
1.2.4. Temperature controller which allows you to set the desired temperature of the water heating
1.2.5. Thermostat controlling the temperature of water in the tank
3
1.2.6. Safety valve which is installed at the inlet of the water heater and serves to prevent the return of water to the water Do not use the water heater with a damaged power supply cable
line and protect the tank from excessive pressure
1.2.7. Magnesium anode rod providing additional protection of the inner tank from corrosion
TECHNICAL CHARACTERISTICS
4
Do not leave anything on top of the appliance
Product range
Enamel
Weight
(kg)
Inox
5
Do not climb onto the appliance
This appliance is conforming with the international standards:
- Electrical safety standards IEC 60335-1 and IEC 60335-2-21.
Before cleaning, isolate the appliance from the mains by
- EMC Electro-Magnetic Compatibility: EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.
unplugging it or turning the switch o
6
The products are compliant according to:
- TP TC 004/2011 «Technical regulations of the Customs Union on safety of low voltage equipment».
- TP TC 020/2011 «Technical regulations of the Customs Union on electro-magnetic compatibility».
Install the appliance on a solid wall that is not subjected to
7
any vibrations

2. INSTALLATION

Attention! The installation and set-up of the water heater must be carried out by a qualified technician in con-
Make electrical connections using cables with conductors
8
formity with the applicable rules and hygiene and sanitary standards in force and with any provisions set forth
of suitable section
in this manual.
2.1. Hot-water boiler bonding against the wall
Make sure all control and protection functions operate correctly
9
2.1.1. Water heater mounting is made on the main wall using brackets and fastening hooks. Fastening hooks (not included in the
before start the appliance
supply) with a diameter of at least 12 mm are recommended. Depending on the model, you will need 2 or 4 of the fastening hooks.
2.1.2. Prepared fastening must support a weight that is three times higher than the weight of the water heater filled with water.
2.1.3. The appliance should be installed as close as possible to the point of water intake to limit heat (A in Fig. 1).
ADDITIONAL SAFETY RULES
2.1.4. Allow for a clearance of at least 50 cm under the appliance and a clearance of 10 cm from the ceiling for maintenance.
2.1.5. Fastening of hooks to the wall must prevent inadvertent movement of the bracket of the water heater over them. After
10
Before water heater handling, drain hot water
installation, be sure to check security of the fastening.
2.1.6. To prevent the property of the customer and (or) third party from damage caused by failures of hot water supply system,
it is recommended to mount the water heater in the premises provided with waterproof floor and sewer drain. Never put objects
sensitive to water under the water heater.
Descale the components in accordance with the instructions
2.1.7. During mounting water heater in the unprotected areas, you must install underneath the protective tray with drainage
provided in the applicable document. Air the room.
into the sewer.
11
Work is performed in protective clothing, avoiding mixing
di erent products. The water heater and surrounding
objects shall be protected against ingress of cleansers
Do not use any insecticides, solvents or aggressive detergents
12
to clean the appliance
54 54
Warning
30 40 50
SLIM SLIM SLIM
12 14 17
9 11 12
Meaning
Electric shock. Burns due to the contact with overheated
components. Injuries due to the contact with sharp edges or
protrusions
Electric shock in case of cable, plug, or socket damage
Electric shock from live unsheathed wires under voltage
Injury from an object falling o the appliance due to its vibrations
Damage to the appliance or any objects underneath it due to the
65 80
50
object falling o following vibrations
SLIM SLIM
19 21 15
Injury from the falling appliance
14 16 12
Damage to the appliance or any objects underneath it due to the
appliance falling o from its place of installation
Electric shock
Excessive noise
Incorrect conductor section results in cables overheating.
It may cause re.
Shutdown or damage of the appliance due to out-of-service
or unregulated control system operation
Burns
Injury due to contact of the skin or eyes with acidic substances,
inhalation or swallowing of harmful chemical agents.
Damage to the appliance or surrounding objects due to corrosion
caused by acidic substances
Damage to the plastic and painted parts
Risk
80 100 120
19 23 28
15 17 20
Symbol
150
32
25