Installation; Displays And Operating Elements - Pantron IMX-N830 Operating Instructions Manual

GB Operating Instructions
8-channel light barrier multiplexer IMX-N830
5.4.1 NPN-circuit
external
supply
12 VDC - 30 VDC
R R
L L
5.4.2 PNP-circuit
external
supply
12 VDC - 30 VDC
R R
L L
5.5 Master OUT
To synchronize more than one 8-channel multiplexer, the
Master OUT output (connection terminal number 25, see picture
1) gives a signal to the following device.
i
Do not connect the Master OUT terminal with the
Master OUT terminal of the next device.
5.6 Slave IN
1
To synchronize more than one 8-channel multiplexer, the
Slave IN input (connection terminal number 24, see picture
1) receives the signal from the previous device.
i
The Slave IN connector should be wired to a Master
OUT connector.
6.

Displays and operating elements

H1 H2 H3 H4 H5
H12 H13 H14 H15
H16
P1 P2 P3 P4 P5
8-CHANNEL INFRARED MULTIPLEXER
S1 - S8
H1 - H8 Output status indicator (yellow)
H9 Slave operation indicator (yellow)
H10 Light curtain mode (yellow)
H11 Power ON indicator (green)
H12 - H19 Sensitivity indicator (green)
P1 - P8 Sensitivity adjusters (channel 1 - 8)
P9 Switching ON delay (output no. 1)
P10 Switching OFF delay (output no. 1)
S1 - S8 Switching mode (channel 1 - 8)
S9 - S12 Functions
OI160103DE/EN
R R R R R R
L L L L L
R R R R R R
L L L L L
H6 H7 H8 H9 H10 H11
H18 H19
H17
P8
P6 P7 P9 P10
FUNCTION ON OFF
SW
1 Transmit Power 100% 20%
2 Multiplex-Speed low high
3 Relay1= Curtain yes no
4 Delay Timer 0-15s off
S9 - S12
7. Choose the sensor heads
Before you turn on the multiplexer, select the transmitter
and receiver for your application. Each channel needs one
transmitter and one receiver. This includes choosing the
sensor heads body style and cable length or quick disconnect
L
that meets your requirements.
8.

Installation

The multiplexer can be installed with two holes (DIN 46121)
V. SUPPLY
or a DIN rail mounting clip (DIN 46277). The wiring diagramm
is printed on the front label of the multiplexer or see picture
2: Wiring diagram.
9. Choose the functions
The functions are selectable by DIP-switches located on
L
the front side of the multiplexer (see also table 4).
S9 - transmit power
V. SUPPLY
S11 - Light curtain function
(Output 1 = curtain)
table 4: DIP-switches S9 - S12
9.1 Switching mode
The switching function describes the output behavior on
interruption of the infrared beam. There are two types of
switching functions: Light and Dark Mode.
Light mode: When the beam is interrupted, the NPN-circuit
switches to ground, PNP-circuit is open.
Dark mode: In contrast to the light mode, the NPN-circuit
is open, and the PNP-circuit switches the external supply
to the output.
When the beam is not interrupted, the states turns round.
The switching mode is selectable by the DIP-switches S1 to
S8. The number of the DIP-switch is equal with the number of
the transmit channel. If the DIP-switch is in the OFF postion
the function is set to light mode and if the DIP-switch is in
the ON postion the function is set to dark mode.
9.2 Transmit Power
The transmit power of the multiplexer can be switched to
less sensitive.
100%: The multiplexer has the maximum sensitivity value
(highest range).
20%: The multiplexer has 20% of the maximum sensitivity
value.
1 Inscription front label
S10 - Multiplex rate
1
(Multiplex speed)
20%
100%
S12 - Time delay
(Delay Timer)
1
inactive (no)
1
active (yes)
1
1
1
1
16 ms (high)
1
32 ms (low)
1
1
inactive (off)
1
0 - 15 s
9
/12