Table of Contents
Advertisement
To Select a Desired Channel
You can select a desired channel by using
the Number buttons
directly pressing
• Enter a channel numbers as a two-digit number for the
quickest results. For example, to select channel 6, press
and
6
. If you only press
brief delay.
• You can only select channels 01–99.
Manual Channel Preset
• Use the remote control for this procedure.
1) Press
VCR
SETUP
, then
2) Press
or
to select "INITIAL", then press
K
L
3) Press
or
to select "CH TUNING", then press
K
L
4) Press
or
to select "MANUAL", then press
K
L
5) Press
or
to select "POSITION", then press
K
L
•When a weak signal is received in Manual Tuning mode,
you can change the background to solid blue or the
static screen by pressing
6) Press
the Number buttons
position number, then press
•You can select position number 01-99.
•If "ON" appears on the right side of "SKIP", press
to point to "SKIP". Then, press
L
•If you want to remove scrambled signals, press
repeatedly to point to "DECODER". Then, press
select "ON".
7) Press
or
to select "CHANNEL", then press
K
L
8) Press
or
to start scanning.
K
L
•The unit's tuner will begin to search up or down
automatically. When a channel is found, the unit will
stop searching and the picture will appear on the TV
Screen.
•You can select desired channel number by using
the Number buttons
Channel Plan table and press three digits to select the
channel number.
(To select channel 24, press "
press "
2
" and "
4
".)
•If this is the channel you want, press
Channel Plan
CH Indication
01 – 10
21 – 69
74 – 78
80 – 99, 100
121 – 141
This unit can receive Hyper and Oscar frequency bands.
9) Press
SETUP
to exit.
Note: •
To confirm that a channel has been added, press
CHANNEL
(
/
).
K
L
MENU
TIMER
SET UP
INITIAL
MANUAL
POSITION
P08
008
CHANNEL
[OFF]
DECODER
[OFF]
SKIP
CHANNEL
on the remote control.
6
, channel 6 will be selected after a
.
B
B
C.RESET
.
,
or
to select your desired
K
L
.
B
to select "OFF".
B
. You must refer to the following
0
" button first and then
.
B
TV Channel
IRA – IRJ, GAP
E21 – E69
X, Y, Z, Z+1, Z+2
S1 – S20, GAP
S21 – S41
INITIAL
CH TUNING
CLOCK
CH TUNING
AUTO
MANUAL
MOVE
To Skip a Preset Channel
(
/
), or
K
L
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL
0
• Use the remote control for this procedure.
1) Press
VCR
2) Press
K
3) Press
K
4) Press
K
5) Press
K
6) Press
the Number buttons
.
position number, then press
.
B
7) Press
K
.
"ON".
.
B
•To memorise the channel again, press
change to "OFF".
8) Press
SETUP
Note: •
To confirm that a channel has been deleted, press
CHANNEL
or
K
MENU
TIMER
or
SET UP
K
L
INITIAL
to
B
.
B
MANUAL
POSITION
CHANNEL
DECODER
SKIP
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
VCR
1) Press
2) Press
K
3) Press
K
4) Press
K
5) Press
K
want to change the channel, then press
•You cannot select a position number where "- - -"
appears next to the number. This is because "SKIP" is
set to "ON" for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to solid blue by pressing
If you press
to the static screen.
6) Press
K
position number, then press
10
(
/
).
K
L
SETUP
, then
.
or
to select "INITIAL", then press
L
or
to select "CH TUNING", then press
L
or
to select "MANUAL", then press
L
or
to select "POSITION", then press
L
,
or
K
L
.
B
or
to select "SKIP", then press
L
to exit.
(
/
).
K
L
P08
008
[OFF]
[ON]
SETUP
, then
.
or
to select "INITIAL", then press
L
or
to select "CH TUNING", then press
L
or
repeatedly to select "MOVE", then press
L
or
repeatedly to select the position number you
L
C.RESET
C.RESET
again, the background will return
or
repeatedly until the channel move to another
L
.
B
.
B
.
B
.
B
.
B
to select relevant
to select
B
. "ON" will
B
INITIAL
CH TUNING
CLOCK
CH TUNING
AUTO
MANUAL
MOVE
.
B
.
B
.
B
.
B
.
EN
Advertisement
Table of Contents
