Related Manuals for Sanyo PLC-XT30
Summary of Contents for Sanyo PLC-XT30
- Page 1 Multimedia Projector PLC-XT25/PLC-XT25L MODEL PLC-XT21/PLC-XT21L PLC-XT20/PLC-XT20L PLC-XT25K/PLC-XT20K PLC-XT30/PLC-XT30L (*Models without lens.) Owner’s Manual...
-
Page 2: Features And Design
Features and Design ◆ ◆ Compact Design Power Management This projector is designed compact in size and The Power management function reduces power weight. It is easy to carry and installed anywhere you consumption and maintains lamp life (p.58). wish to use. ◆... -
Page 3: Table Of Contents
Table of Contents Features and Design ....2 Input Selection ....33 Table of Contents . -
Page 4: To The Owner
Your SANYO product is designed and manufactured with high quality... -
Page 5: Safety Instructions
Safety Instructions All the safety and operating instructions should be read Do not install the projector near the ventilation duct of air- before the product is operated. conditioning equipment. Read all of the instructions given here and retain them for This projector should be operated only from the type of later use. -
Page 6: Air Circulation
Safety Instructions Air Circulation Openings in the cabinet are provided for ventilation. IMPORTANT! To ensure reliable operation of the product and to protect it from overheating, these openings must not Clean the Filter Regularly!! be blocked or covered. The projector uses a lamp which generates significant heat. -
Page 7: Installing The Projector In Proper Directions
Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the plane of the screen as shown in the figure below. -
Page 8: Moving The Projector
Safety Instructions Moving the Projector Use the hand grip when moving the projector. Replace the lens cap and retract the adjustable feet to prevent damage to the lens and cabinet when carrying. When the projector is not in use for an extended period, put it into a suitable case to protect the projector. -
Page 9: Compliance
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number(s) : PLC-XT30, PLC-XT30L, PLC-XT25, PLC-XT25L, PLC-XT21, PLC-XT21L, PLC-XT20, PLC-XT20L Trade Name : Sanyo... -
Page 10: Part Names And Functions
Part Names and Functions q Filter Front w Speaker e Lens Release Button r Top Controls and Indicators t Maintenance Cover WARNING: FOR MAINTENANCE USE ONLY. DO NOT OPEN. y Lens Cap (for PLC-XT25/XT25K/XT21/XT20/XT20K) CAUTION Do not turn on the projector with the lens cap attached. -
Page 11: Rear Terminal
Part Names and Functions Rear Terminal q 5 BNC INPUT JACKS y S-VIDEO INPUT JACK Connect the component or composite video output Connect the S-VIDEO output signal from video signal from video equipment to VIDEO/Y, Cb/Pb, equipment to this jack (p.23). and Cr/Pr jacks or connect the computer output signal (5 BNC Type [Green, Blue, Red, Horiz. - Page 12 Part Names and Functions Rear Terminal ✽ !0 R/C JACK When using the wired remote control, connect the wired remote control to this jack with a remote control cable (not supplied). !1 AUDIO MONITOR OUTPUT JACK (VARIABLE) This jack outputs the audio signal from computer or video equipment to external audio equipment (pp.22–24).
-
Page 13: Top Control
Part Names and Functions Top Control q WARNING TEMP. indicator u SELECT button Blinks red when the internal temperature of the – Execute the selected item (p.27). projector exceeds the operating range (pp.67, 73). – Expand or compress the image in the Digital zoom mode (p.51). -
Page 14: Remote Control
Part Names and Functions Remote Control q STAND-BY button o POINT ed 7 8 ( VOLUME + / – ) buttons Turn the projector off (p.26). – Select an item or adjust the value in the On- Screen Menu (p.27). w WIRED REMOTE jack –... - Page 15 Part Names and Functions Remote Control For PIN code and remote control code. !3 MENU button @0 FOCUS button Open or close the On-Screen Menu (p.27). Adjust the focus (p.31). !4 P-TIMER button @1 NO SHOW button Operate the P-timer function (p.32). Temporarily turn off the image on the screen (p.32).
-
Page 16: Laser Pointer Function
Part Names and Functions Laser Pointer Function This remote control emits a laser beam from the laser light window. Press the LASER button to activate the laser pointer. The signal emission indicator lights red and the red laser beam is emitted. If the LASER button is pressed for more than one minute or if it is released, the laser light goes off. -
Page 17: Wireless Mouse Operation
Part Names and Functions Wireless Mouse Operation The remote control can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect PRESENTATION POINTER your computer and the projector with the button supplied USB cable. (See page 22 for Move the pointer on the screen connection.) with this button. -
Page 18: Remote Control Battery Installation
Part Names and Functions Remote Control Battery Installation Open the battery Install new batteries Replace the compartment lid. into the compartment. compartment lid. Press the lid Two AAA size batteries downward and slide it. For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment. -
Page 19: Installation
Installation Lens Installation When replacing the lens or using an optional lens, install the lens by following the instructions below. Ask the sales dealer for detailed information of the optional lens specifications. Lens Release button Removing the lens Shift the lens to the center position by using the Lens shift function (see page 29). -
Page 20: Positioning The Projector
Installation Positioning the Projector (for PLC-XT30/PLC-XT25/XT25K/XT21/XT20/XT20K) For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. ✔ Notes: •The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image. -
Page 21: Connecting The Ac Power Cord
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100–120 V or 200–240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. -
Page 22: Connecting To A Computer (Digital And Analog Rgb)
Installation Connecting to a Computer (Digital and Analog RGB) Cables used for connection • VGA Cable (HDB 15 pin)* • USB Cable • DVI-Digital Cable • Audio Cables (Mini Plug [stereo] x 2) • BNC Cable (*One cable is supplied; other cables are not supplied with the projector.) Monitor Audio Monitor... -
Page 23: Connecting To Video Equipment (Video, S-Video)
Installation Connecting to Video Equipment (Video, S-Video) Cables used for connection • Video Cables (RCA x 1) • Audio Cables (Mini Plug [stereo] x 2) • S-VIDEO Cable • BNC Cable • Audio Cable (RCA x 2) (Cables are not supplied with the projector.) S-video Composite Video and Audio Output Output... -
Page 24: Connecting To Video Equipment (Component And Rgb Scart)
Installation Connecting to Video Equipment (Component and RGB Scart) Cables used for connection • Audio Cables (Mini Plug [stereo] x 2) • Scart-VGA Cable • BNC Cable • DVI-Digital Cable (Cables are not supplied with the projector.) Component Video Digital Output Audio RGB Scart Output... -
Page 25: Basic Operation
Basic Operation Turning On the Projector Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. Connect the projector’s AC power cord into an AC outlet. The POWER indicator lights green. Press the ON/STAND-BY button on the top control or the ON button on the remote control. -
Page 26: Turning Off The Projector
Basic Operation Turning Off the Projector Press the ON/STAND-BY button on the top control or the STAND-BY button on the remote control, and “Power off?” appears on the screen. Press the ON/STAND-BY button or the STAND-BY button on the remote control again to turn off the projector. -
Page 27: How To Operate The On-Screen Menu
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Top Control Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. MENU button Press the MENU button on the top control or the remote control to display the On-Screen Menu. -
Page 28: Menu Bar
Basic Operation Menu Bar For detailed functions of each menu, see “Menu Tree” on pages 71–72. The menu bar displays changes depending on the input signals. Guide Window System [PC Adjust] Image Adjust Setting Menu Show the selected Select a Adjust Adjust the picture Set the projector’s... -
Page 29: Operating With Projector Control
Basic Operation Operating with Projector Control Lens Operation Top Control The following lens operation can be made with the Lens INFO. button on the top control. button Press the Lens button to enter each lens operation mode. LENS MENU The selected adjustment display appears on the screen. button button POINT... -
Page 30: Sound Adjustment
Basic Operation Sound Adjustment Direct Operation Top Control VOLUME +/– buttons Volume Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE button on the remote control to temporarily Remote Control... -
Page 31: Operating With Remote Control
Basic Operation Operating with Remote Control Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. FREEZE button Remote Control Press the FREEZE button on the remote control to freeze the picture on the screen. - Page 32 Basic Operation NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. “No show” disappears after 4 seconds. P-TIMER button Press the P-TIMER button on the remote control.
-
Page 33: Input Selection
Input Selection Select the input signal of equipment connected to the projector. This projector has three input options (INPUT 1, INPUT 2, and INPUT 3) and they are categorized by different signal type. Select an input source with the INPUT button on the top control or the INPUT 1–3 buttons on the remote control, or by On-Screen Menu. -
Page 34: Input
Input Selection Input Remote Control Remote Control button operation INPUT buttons RGB (Scart) RGB (PC digital) Remote Control Operation Press the INPUT 1, INPUT 2, or INPUT 3 buttons on the RGB (AV HDCP) remote control. The input source appears on the screen as you press each button. -
Page 35: Input Source Selection
Input Selection Input Source Selection Menu Operation Input Menu Press the MENU button to display the On-Screen Menu. Use the Point buttons to move the red frame pointer to the Input Menu icon. Use the Point buttons to move the red arrow pointer to the desired input and then press the SELECT button. -
Page 36: Video System Selection
Input Selection Video System Selection Press the MENU button to display the On-Screen AV System Menu (Video or S-Video) Menu. Use the Point buttons to move the red frame pointer to the AV System Menu icon. Use the Point buttons to move the red arrow AV System Menu icon pointer to the desired system and then press the The selected system is... -
Page 37: Computer Adjustment
Computer Adjustment Adjust the computer screen. This projector has various types of signal formats to automatically tunes to most computers. With these signal formats in the projector and the Auto PC Adjustment function, no special setting is required and you can enjoy the images in computers just by connecting the computer to the projector. -
Page 38: Computer System Selection
Computer Adjustment Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings. -
Page 39: Auto Pc Adjustment
Computer Adjustment Auto PC Adjustment Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical positions to conform to your computer. Direct Operation Remote Control The Auto PC adjustment function can be operated directly by pressing the AUTO PC button on the remote control. -
Page 40: Manual Pc Adjustment
Computer Adjustment Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. - Page 41 Computer Adjustment Display area H Use the Point buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point buttons to adjust the vertical area displayed by this projector. Reset Move the red frame pointer to the desired item and press the To reset the adjusted data, select Reset and press the SELECT button.
- Page 42 Computer Adjustment MEMO...
-
Page 43: Image Mode Selection
Image Mode Selection You can choose an image mode in accordance with each projected image such as presentation screen, movies, etc. You can also adjust image parameters in the Image Adjust Menu and save them as Image 1–4. The four image modes with respect to each input source are stored. Select Image Mode with the On-Screen Menu. -
Page 44: Image Mode Selection
Image Mode Selection Image Mode Selection Press the MENU button to display the On-Screen Image Menu icon Image Menu Menu. Use the Point buttons to move the red frame pointer to the Image Menu icon. Use the Point buttons to move the red frame pointer to the desired image mode and then press the Move the red frame pointer to SELECT button. -
Page 45: Image Adjustment
Image Adjustment You can adjust the following image parameters. Contrast Brightness Color* Tint* Color Temperature White balance (Red) White balance (Green) White balance (Blue) Sharpness Gamma Noise reduction* This function can reduce noise interference on the screen. Certain images may be inapplicable. -
Page 46: Image Adjustment
Image Adjustment Image Adjustment Press the MENU button to display the On-Screen *The figure below shows for video signal input. Menu. Use the Point buttons to move the red Image Adjust Menu frame pointer to the Image Adjust Menu icon. Use the Point buttons to move the red frame pointer to the desired item and then press the SELECT... - Page 47 Image Adjustment Sharpness Press the Point button to decrease the sharpness of the image; press the Point button to increase the sharpness of the image (from 0 to 15). Gamma Use the Point buttons to adjust the gamma value to obtain a better balance of contrast (from 0 to 15).
- Page 48 Image Adjustment Reset To reset the adjusted data, select Reset and press the Image Mode Menu SELECT button. A confirmation box appears and then select Move the red frame [Yes]. All adjustments will return to their previous figures. pointer to an image item to be set and Store then press the...
-
Page 49: Screen Adjustment
Screen Adjustment You can change or adjust the appearance of the image as well as the image orientation with the following options. Screen size --------------------- Select a screen size conforming to the input signal source. Digital zoom -------------------- Zoom up and down the images. (Only available with the computer signals.) Keystone ------------------------ Correct Keystone distortion. -
Page 50: Screen Adjustment
Screen Adjustment Screen Adjustment Press the MENU button to display the On-Screen Screen Menu Menu. Use the Point buttons to move the red frame pointer to the Screen Menu icon. Use the Point buttons to move the red frame Screen Menu icon pointer to the desired function and then press the Move the red frame pointer SELECT button. -
Page 51: Screen Size Adjustment (Computer Signals)
Screen Adjustment Screen Size Adjustment (Computer Signals) Select the desired screen size that conforms to the input signal source. Screen Menu Normal Provide the image to fit the screen size. Screen Menu icon Move the red frame pointer True to the desired function and Provide the image in its original size. -
Page 52: Screen Size Adjustment (Video, Component Signals)
Screen Adjustment Screen Size Adjustment (Video, Component Signals) Press the MENU button to display the On-Screen Screen Menu Menu. Use the Point buttons to move the red frame pointer to the Screen Menu icon. Use the Point buttons to move the red frame Screen Menu icon pointer to the desired function and then press the Move the red frame pointer... -
Page 53: Setting
Setting The following setting options are available: Language ------------------------ Select the language of the On-Screen Menu. Background --------------------- Select the background image for no signal input. Lamp control ------------------- Select the brightness of the lamp. Pointer ---------------------------- Select the pointer shape. Logo -------------------------------- Customize the screen logo Remote control---------------- Select the remote control code. -
Page 54: Setting
Setting Setting This projector has a Setting menu that allows you to set up Setting Menu (Language) the other various functions described below. Press the MENU button to display the On-Screen Setting Menu icon Menu. Use the Point buttons to move the red frame pointer to the Setting Menu icon. - Page 55 Setting Logo Logo (Logo and Logo PIN code lock settings) This function allows you to customize the screen logo with Logo select, Capture, and Logo PIN code lock functions. ✔ Note: •When “On” is selected in the Logo PIN code lock function, Logo select and Capture functions cannot be selected.
- Page 56 Setting Logo PIN code lock Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. Off.... The screen logo can be changed freely from the Logo Menu (p.55). On .... The screen logo cannot be changed without a Logo PIN code.
- Page 57 Setting Remote control Remote control The eight different remote control codes (Code 1–Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should set on both the projector and the remote control.
- Page 58 Setting Power management Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. Time left before the lamp is off. If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with “No signal”...
- Page 59 Setting Fan control Fan control This function is used to set the cooling fans’ operation to the projector’s setting environment. Set this function properly in accordance with the projector’s installation method. Otherwise, the cooling fans will not work properly and that causes malfunctions of the projector and decreases the lamp life.
- Page 60 Setting PIN code lock PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off.... Unlocked. On1 ..Enter the PIN code every time turning on the projector. On2 ..
- Page 61 Setting Change the PIN code Change the PIN code The PIN code can be changed to your desired four-digit number. Press the Point buttons to select “PIN code change” and press the SELECT button. The New PIN code input dialog box appears. Set a new PIN code. CAUTION: WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN THE NEW PIN...
- Page 62 Setting Filter counter Filter counter This function is used to set a frequency for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon (yellow) appears on the screen and the WARNING FILTER indicator lights orange, notifying the cleaning is necessary.
-
Page 63: Maintenance And Filter Cleaning
Maintenance and Filter Cleaning In order to care for the projector appropriately, regular maintenance is required. The instructions described here will help minimize the need for optical cleaning, reduce the likelihood of costly repairs, and maximize lamp life. The projector uses a lamp which generates significant heat and thus requires a large amount of air to be drawn through the filter to cool the units. -
Page 64: Cleaning The Filter
Maintenance and Filter Cleaning Cleaning the Filter Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector. -
Page 65: Lamp Replacement
Maintenance and Filter Cleaning Lamp Replacement Top Control When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP LAMP REPLACE REPLACE indicator should light is depending on the lamp indicator... -
Page 66: Resetting The Lamp Counter
Maintenance and Filter Cleaning Resetting the Lamp Counter Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the LAMP REPLACE indicator stops lighting and the Lamp replacement icon disappears. Lamp counter Press the MENU button to display the On-Screen Menu. -
Page 67: Warning Indicator
Maintenance and Filter Cleaning Warning Indicators The WARNING indicators show the state of the function which protects the projector. Check the state of the WARNING indicators and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING Top Control TEMP . -
Page 68: Cleaning The Projection Lens
Maintenance and Filter Cleaning Cleaning the Projection Lens Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. -
Page 69: Appendix
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. –Make sure you have properly connected the projector to peripheral equipment as described on pages 22–24. –Make sure all equipment is connected to AC outlet and the power is turned on. –When the projector does not project an image from the connected computer, restart the computer. - Page 70 Appendix Some displays are not seen – Check the Display function. See page 57. during the operation. PIN code dialog box appears – PIN code lock is being set. Enter a PIN code (the “1234” or numbers at start-up. you have set). See pages 25, 60–61. The Remote Control does –...
-
Page 71: Menu Tree
Appendix Menu Tree Input Input 1 RGB (PC Analog) Go to System RGB (Scart) RGB (PC Digital) RGB (AV HDCP) Quit Input 2 Go to System Video Go to System Component Go to System Quit Input 3 Auto Video Go to System S-video Go to System Quit... - Page 72 Appendix PC Adjust Setting Auto PC adj. Language 12 languages provided Fine sync 0–31 Quit Total dots Logo Logo select Horizontal Off/Default/User Vertical Capture Current mode H-sync freq. Yes/No V-sync freq. Logo PIN code lock Quit On/Off Clamp Logo PIN code change Display area H Quit Display area V...
-
Page 73: Indicators And Projector Condition
Appendix Indicators and Projector Condition Check the indicators for the projector condition. WARNING TEMP . indicator Indicators Projector Condition WARNING POWER LAMP TEMP. green The projector is off. (The AC power cord is unplugged.) The projector is in stand-by mode. Press the ON/STAND-BY button to turn on the projector. - Page 74 Appendix WARNING FILTER indicator Indicators Projector Condition WARNING POWER LAMP FILTER green orange The filter is clogged. Stop using the projector immediately and clean or replace the filter (see below). Filter warning red icon – – The Filter counter reached a set time. Clean or replace the filter as soon as possible.
-
Page 75: Compatible Computer Specifications
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below and less than 140 MHz of Dot Clock. PC Adjustment is limited when selecting these modes. ON-SCREEN H-Freq. V-Freq. ON-SCREEN H-Freq. - Page 76 Appendix When an input signal is digital from the DVI terminal, refer to the chart below. PC Adjust Menu cannot be selected when Input 1 [RGB (PC digital)] is selected in the Input Menu. ON-SCREEN H-Freq. V-Freq. ON-SCREEN H-Freq. V-Freq. RESOLUTION RESOLUTION DISPLAY...
-
Page 77: Technical Specifications
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 13.7” x 6.46” x.17.48” (348.1 mm x 164 mm x 444 mm) (Not including adjustable feet) Net Weight 19.2 lbs (8.7 kg) Feet Adjustment 0˚ to 5.0˚ Panel Resolution LCD Panel System 1.0”... -
Page 78: Optional Parts
AC Power Cord Remote Control and Batteries VGA Cable USB Cable Lens Cap (for PLC-XT30/PLC-XT25/XT25K/XT21/XT20/XT20K) Lens Mount Cover (for PLC-XT30L/PLC-XT25L/XT21LXT20L) PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. -
Page 79: Pj Link Notice
Appendix PJ Link Notice This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input PJLink Input Parameter... -
Page 80: Configurations Of Terminals
Appendix Configurations of Terminals INPUT 1/ANALOG OUT Terminal: Analog RGB (Mini D-sub 15 pin) Red (R/Cr) Input/Output +5V Power/ ----- Green (G/Y) Input/Output Ground (Vert.sync.) Blue (B/Cb) Input/Output Ground/ ----- ----- DDC Data/ ----- Ground (Horiz.sync.) Horiz. sync. Input (Composite H/V sync.) Ground (Red) Vert. -
Page 81: Pin Code Number Memo
Appendix PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. -
Page 82: Dimensions
Appendix Dimensions 13.7 (348.1) Unit: inch (mm) 5º MAX 1.65 (41.9) 11.10 (282) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) 7.87 (200) - Page 83 MZ7A-B SANYO Electric Co., Ltd.