Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Greenlee GATOR EK6FTILX
Summary of Contents for Greenlee GATOR EK6FTILX
- Page 1 Serial Number EK6FTLX, EK6FTILX GATOR Battery-powered, ® Crimping Tool Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com 52080023 REV4 © 2019 Greenlee Tools, Inc. 1/19...
-
Page 2: Table Of Contents
All specifications are nominal and may change as design manual, may cause harmful interference to radio com- improvements occur. Greenlee Tools, Inc. shall not be liable for munications. Operation of this equipment in a residential damages resulting from misapplication or misuse of its products. -
Page 3: Important Safety Information
Failure to observe this warning could ing tool head when crimping. result in severe injury or death. Failure to observe these warnings could result in severe injury or death. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... - Page 4 Injury or damage to the tool may result. Failure to observe this precaution may result in injury and property damage. Note: Keep all decals clean and legible, and replace when necessary. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
-
Page 5: Identification
Battery Technology ..................MAKITA Lithium ion ® ® Inline ..............BL1815, BL1820, BL1830, BL1840, BL1850 Pistol ....................BL1830, BL1840, BL1850 MAKITA is a registered trademark of Makita Corporation. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 6: Operation
Circuit has become too hot Flashing light for 20 seconds Send tool in for service at end of cycle * Running the battery below 16 V can damage the battery. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... - Page 7 Failure to observe these warnings could result in severe injury or death. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
-
Page 8: Connector Selection
1/0 AWG to 350 kcmil: 2 crimps Panduit: 4 AWG to 500 kcmil 750 kcmil: 3 crimps 400 to 600 kcmil: 3 crimps Penn-Union: 6 AWG to 500 kcmil 750 kcmil: 4 crimps Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 9: Lcd Screen
Tool deactivated Service necessary Real-time clock not found Bluetooth unit not found ® Pressure sensor not found Burst pressure exceeded Battery temperature too low Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 10: Maintenance
3. Inspect the rotation of the head assembly. Fully debris or hydraulic oil. retract the ram. The head should rotate no more than 360°. If damage is detected, contact Greenlee customer service at 800-435-0786 for warranty service or repair. After use: 1. -
Page 11: Troubleshooting
800-435-0786 for warranty service or repair. Air in hydraulic system. Pull trigger and hold retract button simultane- ously. Run for approximately 10 seconds, and then attempt to crimp. If unsuccessful, contact Greenlee customer service at 800-435-0786 for warranty service or repair. Cold oil. - Page 12 4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 ©2019 Greenlee Tools, Inc. • An ISO 9001 Company Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 www.greenlee.com...