Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Greenlee GATOR EK628
Summary of Contents for Greenlee GATOR EK628
- Page 1 INSTRUCTION MANUAL Serialnummer EK628 GATOR ® Battery-powered Crimping Tool Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 52023597 REV 3 © 2008 Greenlee Textron Inc. 5/08...
-
Page 2: Table Of Contents
All specifications are nominal and may change as design improvements occur. Greenlee Textron Inc. shall not be liable for damages resulting from misapplication or misuse of its products. GATOR is a registered trademark of Greenlee Textron Inc. -
Page 3: Important Safety Information
Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company EK628 Battery-powered Crimping Tool Wear eye protection when operat- ing or servicing this tool. Failure to wear eye protection could result in serious eye injury from flying debris or hydraulic oil. - Page 4 Use this tool for the manufacturer’s intended purpose only. Failure to observe these precautions may result in injury or property damage. Greenlee / A Textron Company EK628 Battery-powered Crimping Tool Do not allow anything to contact the battery terminals. •...
-
Page 5: Identification
Average Crimping Time ...4 seconds Average Crimps per Charge ...approximately 70 Battery Charging Voltage ... 9.6 V Charging Time ...45 min Greenlee / A Textron Company EK628 Battery-powered Crimping Tool 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 6: Operation
Use this tool for the manufacturer’s intended purpose only. Failure to observe these precautions may result in injury or property damage. Greenlee / A Textron Company EK628 Battery-powered Crimping Tool Charging the Battery Read the instructions supplied with the battery charger. - Page 7 First Compression SIDE A First Compression Crimping Direction SIDE A Greenlee / A Textron Company EK628 Battery-powered Crimping Tool Crimping Procedure 1. Insert conductor into the connector and align the tool and die on the connector. Start in the center for splices and on the end, nearest the pad, for terminals.
-
Page 8: Die Selection
Die Selection Crimps made on copper cable with Greenlee KC22-type dies and the copper connectors listed here are cUL and UL classified. Crimps made on copper or aluminum cable with Greenlee KA22-type dies and the dual-rated aluminum connectors listed here are cUL and UL classified. -
Page 9: Maintenance
1. Inspect dies for wear or damage such as cracks, gouges, or chips. 2. Inspect the tool for damage or leaks. If damage is detected, return the tool to an authorized Greenlee service center for inspection. Skin injection hazard: Do not use hands to check for oil leaks. -
Page 10: Illustrations
Illustrations Main Pump Housing Unit, Relief Valve Unit, and Piston Pump Assembly Greenlee / A Textron Company EK628 Battery-powered Crimping Tool 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070 Motor Assembly... - Page 11 EK628 Battery-powered Crimping Tool Illustrations Ram Unit and Crimping Jaw Unit—D Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
-
Page 12: Parts List
800-435-0786 815-397-7070 Canada 800-435-0786 International +1-815-397-7070 4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070 • An ISO 9001 Company Greenlee Textron Inc. is a subsidiary of Textron Inc. www.greenlee.com Fax: 800-451-2632 Fax: 815-397-1865 Fax: 800-524-2853 Fax: +1-815-397-9247...