Hitachi P1-00250HFEF Basic Manual page 88

Chapter 4
[CC-20]～[CC-33]
Output terminal response
Code/Name
CC-20
Output terminal [11] on-delay time
CC-21
Output terminal [11] off-delay time
CC-22
Output terminal [12] on-delay time
CC-23
Output terminal [12] off-delay time
CC-24
Output terminal [13] on-delay time
CC-25
Output terminal [13] off-delay time
CC-26
Output terminal [14] on-delay time
CC-27
Output terminal [14] off-delay time
CC-28
Output terminal [15] on-delay time
CC-29
Output terminal [15] off-delay time
CC-30
Output terminal [16] on-delay time
CC-31
Output terminal [16] off-delay time
CC-32
Output terminal [AL] on-delay time
CC-33
Output terminal [AL] off-delay time
・Sets the delay time since the output terminal changes,
until it actually become responsive.
Function
code
Initial
Range (unit)
value
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00
0.00 100.00(s)
～
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00
0.00 100.00(s)
～
0.00 100.00(s) 0.00
～
0.00 100.00(s) 0.00
～
4-40
For parameter configuration
[Intelligent output terminal function list]
Symbol Function name
000 no Not use
001 RUN Running
Constant-speed
002 FA1
reached
Set speed
003 FA2
overreached
Set frequency
004 FA3
reached
Set speed
005 FA4
overreached 2
006 FA5 Set speed reached
007 IRDY inverter ready
008 FWR Forward rotation
009 RVR Reverse rotation
Speed referenc =
010 FREF
Keypad is selected
Run command =
011 REF
Keypad is selected
2nd control is
012 SETM
selcted
016 OPO Option output
017 AL Alarm
018 MJA Major failure
019 OTQ Over-torque
Instantaneous
020 IP
power failure
021 UV Undervoltage
022 TRQ Torque limited
IP-Non stop function
023 IPS
is active
Accumulated
024 RNT
operation time over
Accumulated
025 ONT
power-on time over
Electronic thermal
026 THM
alarm signal(MTR)
Electronic thermal
027 THC
alarm signal(CTL)
Capacitor life
029 WAC
warning
Cooling-fan speed
030 WAF
drop
Starting contact
031 FR
signal
Heat sink overheat
032 OHF
warning
Low-current
033 LOC
indication signal
Low-current
034 LOC2
indication signal 2
Overload notice
035 OL
advance signal (1)
Overload notice
036 OL2
advance signal (2)
037 BRK Brake release
038 BER Brake error
039 CON Contactor control
Description
While output is active
When constant speed
reached, ON
ON at reaching the specified
frequency or more
ON only at reaching the
specified frequency
ON at reaching the specified
frequency 2 or more
ON only at reaching the
specified frequency 2
ON when inverter is ready
ON while in forward drive
ON while in reverse drive
ON if the frequency
reference is from keypad
ON if the motion
operation is from
operation keypad
ON if 2nd-motor selected
Controlled by the Option
ON when trip happens
ON if major failure trips
ON if torque is exceeded
ON if control power drops
ON if main voltage drops
ON if torque limit operates
ON if set in power loss
ON if set time is exceeded
ON if set time is exceeded
ON if motor thermal
integral value exceeds set
value
ON if inverter thermal
integral value exceeds set
value
ON by life warning
ON by life warning
On while in operation
ON when the heatsink is
overheated.
ON if output current is less
that the specified value
ON if output current is less
that the specified value
ON if output current
exceeds specified value
ON if output current
exceeds specified value
ON when brake releases
ON if abnormality in
sequence happens
ON if contactor releases