Table of Contents
Advertisement
Chapter 4
Chapter 4
Chapter 4
4.1.4 Doing a test
oing a test run...
run...
・This explains the method to how to do a test run using
This explains the method to how to do a test run using
This explains the method to how to do a test run using
This explains the method to how to do a test run using
This explains the method to how to do a test run using
・
the keypad.
.
Home screen
Home screen
RUN
RUN
FW
FW
Output frequency
Output frequency
Output frequency
Output current
Output current
Input terminal monitor
Input terminal monitor
Input terminal monitor
Menu
oFW
(E)↑ (F)↑
(E)↑ (F)↑
4.1.4.1 Confirm the operation command.
4.1.4.1
Confirm the operation command.
Confirm the operation command.
Confirm the operation command.
・In the position
n the position (E) of the upper illustration
of the upper illustration, when is
of the upper illustration
・
displayed FW
displayed FW or RV, the RUN key of the
the RUN key of the
the RUN key of the keypad is
enabled.
⇒Go to
Go to
[4.1.4.2]
※In the cases that is not displayed, and want
cases that is not displayed, and want to operate
cases that is not displayed, and want
cases that is not displayed, and want
※
from the keypad
keypad, or want to change the RUN command
, or want to change the RUN command
, or want to change the RUN command
, or want to change the RUN command
reference to FW
to FW terminal
terminal, is necessary to change the
RUN command selection.
RUN command selection.
RUN command selection.
⇒Go to
[4.
4.1.4.4 Run Command reference change
1.4.4 Run Command reference change
1.4.4 Run Command reference change]
1.4.4 Run Command reference change
4.1.4.2 Frequency reference
4.1.4.2
requency reference status checking
requency reference
・In the upper illustration, in the position (F), when values
In the upper illustration, in the position (F), when values
In the upper illustration, in the position (F), when values
In the upper illustration, in the position (F), when values
In the upper illustration, in the position (F), when values
・
other than 0.00
other than 0.00 are displayed
are displayed, the frequency reference
is already set. ⇒Go to
is already set.
※In the case that
In the case that 0.00 is displayed, is necessary to
is displayed, is necessary to
is displayed, is necessary to
※
change the
change the value of the frequency reference. In the
case that you want to change to an
you want to change to an analog
you want to change to an
such, the frequency command selection must be
requency command selection must be
requency command selection must be
requency command selection must be
changed.
⇒Go to
Go to
[4.1.4.5]
4.1.4.3
4.1.4.3 Start the
Start the output
output by pressing the RUN
key and the motor will accelerate.
and the motor will accelerate.
and the motor will accelerate.
and the motor will accelerate.
※When the motor does not rotate, please refer to the
When the motor does not rotate, please refer to the
When the motor does not rotate, please refer to the
When the motor does not rotate, please refer to the
When the motor does not rotate, please refer to the
※
troubleshooting.
troubleshooting.
M1
H01
46.49 Hz
46.49 Hz
11.9 A
LLLLLLLLLLL
LLLLLLLLLLL
46.49
Option
, when is
to operate
, is necessary to change the
, is necessary to change the
status checking.
status checking
, the frequency reference
, the frequency reference
[4.1.4.
4.1.4.3]
frequency reference. In the
frequency reference. In the
frequency reference. In the
analog input and
input and
by pressing the RUN
by pressing the RUN
For parameter configuration
For parameter configuration
For parameter configuration
For parameter configuration
4.1.4.4
1.4.4 RUN command
RUN command
RUN command reference change
①
Press the RIGHT
RIGHT( ) key, after moving to the
parameter setting screen and by pressing the SEL(O)
parameter setting screen and by pressing the SEL(O)
parameter setting screen and by pressing the SEL(O)
parameter setting screen and by pressing the SEL(O)
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
key, the parameter section of the parameter setting
key, the parameter section of the parameter setting
key, the parameter section of the parameter setting
key, the parameter section of the parameter setting
screen will blink.
screen will blink.
screen will blink.
STOP
Output frequency
Output frequency
FA-01
Set Speed-M (Keypad
Set Speed
M (Keypad)
Back
oFW
②
Change the code
the code with UP/DOWN/LEFT/RIGHT
(
) keys to
keys to [AA111].
STOP
Output frequency
Output frequency
AA111
RUN command selection_M1
RUN command selection_M1
RUN command selection_M1
01:[FW]/[RV] terminal
01:[FW]/[RV] terminal
01:[FW]/[RV] terminal
Back
oFW
③
Press the SEL
SEL(O) key and then
keys select the RUN operation to be executed
keys select the RUN operation to be executed
keys select the RUN operation to be executed between
keys select the RUN operation to be executed
keys select the RUN operation to be executed
all the choices. In this case
all the choices
. In this case [
one selected.
one
STOP
AA111
RUN command selection_M1
RUN command selection_M1
RUN command selection_M1
00:[FW]/[RV] terminal
:[FW]/[RV] terminal
01:3-wire
wire
02:Keypad
Keypad's RUN key
03:RS485
:RS485
Back
oFW
④
To save the changes press
To save the
changes press the SEL (O)
in the position (E) FW or RV
in the position (E) FW or RV
in the position (E) FW or RV should be displayed. Press
in the position (E) FW or RV
the F1 key, and will
the
, and will go to Home screen.
⇒Go to
Go to
[4.1.4.2
2]
4-5
change
key, after moving to the
key, after moving to the
M1
H03
0.00 Hz
0.00 Hz
29.51 Hz
29.51 Hz
29.51
Option
Option
with UP/DOWN/LEFT/RIGHT
with UP/DOWN/LEFT/RIGHT
M1
H03
0.00 Hz
0.00 Hz
[1-8]
29.51
Option
Option
and then with UP/DOWN
with UP/DOWN(
between
[03:Keypad's RUN key]
's RUN key] is the
M1
H03
29.51
Option
Option
key and then
and then
displayed. Press
displayed. Press
to Home screen.
)
the
Advertisement
Table of Contents
