Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- ment, or poor work results. Model T28523 (Mfd. Since 05/19)
(1 of 2) Spark Deflector (1 of 2) Safety Shield (1 of 2) Tool Rest (Left) ON/OFF Switch Tool Rest (Right) To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model T28523 (Mfd. Since 05/19)
Figure 2. Safety and electrical components. G. Tool Rest (Left): Provides flat surface to rest workpiece on during operations. Includes a V-groove for controlling angle of contact with grinding wheel. Figure 1. Safety components. Figure 3. Left tool rest. Model T28523 (Mfd. Since 05/19)
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL T28523 8" SLOW‐SPEED BENCH GRINDER 1/3 HP Product Dimensions: Weight................................34 lbs. Width (side-to-side) x Depth (front-to-back) x Height............... 16 x 12-1/2 x 15-1/2 in.
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model T28523 (Mfd. Since 05/19)
Page 9
Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model T28523 (Mfd. Since 05/19)
Grinding on top of wheels greatly increases risk of work- SPINDLE NUT. Only tighten wheel spindle nut piece kickback. Always grind on downward part enough to drive wheel and prevent slippage. of wheel. Model T28523 (Mfd. Since 05/19)
Page 12
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -10- Model T28523 (Mfd. Since 05/19)
IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely Wear safety glasses during helpful if you need to return your machine later.
Lock entrances to the shop or disable start switch or power connection to prevent Lag Screw unsupervised use. Flat Washer Machine Base Workbench Figure 9. "Direct Mount" setup. -13- Model T28523 (Mfd. Since 05/19)
Flat bracket (see Figure 11). Re-tighten hex Washer bolts. Safety Shield Figure 13. Example tool rest assembly (left). Bracket Hex Bolt Figure 11. Left safety shield with hardware and bracket. -14- Model T28523 (Mfd. Since 05/19)
Page 17
" (see Figure 15). If the gap reaches ⁄ " and no additional adjustments can be made, replace the grinding wheel. ⁄ " – ⁄ " ⁄ " – ⁄ " Figure 16. Spark deflector gap. Figure 15. Tool rest gap. -15- Model T28523 (Mfd. Since 05/19)
Operating an improperly set up machine properly and the switch must be replaced. may result in malfunction or unexpect- ed results that can lead to serious injury, death, or machine/property damage. -16- Model T28523 (Mfd. Since 05/19)
Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -17- Model T28523 (Mfd. Since 05/19)
Workpiece Wheel Selection Inspection The Model T28523 only accepts Type 1 wheels with a ⁄ " bore. Some workpieces are not suitable for grinding on a bench grinder. Before grinding, inspect all Aluminum oxide and silicon carbide wheels are workpieces for the following: marked in a somewhat uniform manner by all the major manufacturers.
RPM of this wheel Type-1 60 Grit Aluminum Grade L Oxide Vitrified Bond WARNING Grinding can be dangerous Visually inspect this wheel for cracks, nicks,chips Figure 18. Tapping locations when performing a ring test. -19- Model T28523 (Mfd. Since 05/19)
Always adjust tool rest and spark deflector Guard after dressing or replacing grinding wheel. Failure to do so could lead to workpiece kickback and injury. Figure 19. Location of outer guard hardware that must be removed when removing wheel. -20- Model T28523 (Mfd. Since 05/19)
Page 23
Never use warped wheel flanges. Always — If wheel appears to wobble, grinder check flanges before re-installing grinding vibrates excessively, or any other unsafe wheel. condition appears with new wheel, stop grinder and refer to Troubleshooting on Page 25. -21- Model T28523 (Mfd. Since 05/19)
Cast iron handle provides To reduce this risk, only install accessories stabilizing mass for better control. recommended for this machine by Grizzly. NOTICE Refer to our website or latest catalog for additional recommended accessories.
Protecting To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, Cleaning the Model T28523 is relatively easy. maintenance, or service. Vacuum excess debris, and wipe off the remaining dust with a dry cloth. Schedule...
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -25- Model T28523 (Mfd. Since 05/19)
5-15 Plug match your machine. Capacitor Always use the wiring diagram Ground inside the motor junction box. Figure 25. T28523 wiring components. READ ELECTRICAL SAFETY -26- Model T28523 (Mfd. Since 05/19) ON PAGE 25!
SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. MODEL T28523 8" SLOW-SPEED BENCH GRINDER...
Page 30
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -28- Model T28523 (Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.