Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
The Model T24463 6" Bench Grinder is a great grinder for the hobbyist or small shop. Model T24463 gives the user a lot of options with fea- tures like a wire wheel, a grinding wheel, wheel dressing tool, worklight, and coolant tray.
Grinding Wheel Material Aluminum Oxide Wheel Speed 3450 RPM Motor Type TEFC Capacitor Start Induction Horsepower ⁄ Amps 2.1A Phase Single Voltage 120V Cycle 60 Hz Speed 3450 RPM Other Coutry of Origin China Warranty 1 Year Models T24463/T24464 (Mfd. Since 02/16)
Everyday ery. Never operate under the influence of drugs or eyeglasses are NOT approved safety glasses. alcohol, when tired, or when distracted. Models T24463/T24464 (Mfd. Since 02/16)
Page 8
EXPERIENCING DIFFICULTIES. If at any time debris. Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Models T24463/T24464 (Mfd. Since 02/16)
Grinding operator. on top of wheels greatly increases risk of work- piece kickback. Always grind on downward part SPINDLE NUT. Only tighten wheel spindle nut of wheel. enough to drive wheel and prevent slippage. Models T24463/T24464 (Mfd. Since 02/16)
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. Models T24463/T24464 (Mfd. Since 02/16)
IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.
If you cannot find an item on this list, care- fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory. Figure 3. Model T24463 inventory. -11- Models T24463/T24464 (Mfd. Since 02/16)
Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. ⁄ " Weight Load Space Allocation Physical Environment 16" Electrical Installation Lighting Figure 5. Minimum working clearances. -12- Models T24463/T24464 (Mfd. Since 02/16)
" – ⁄ " Work Table Figure 9. Model T24463 spark deflector, safety shield, and tool rest installation. Figure 11. Model T24463 tool rest gap. Note: The tool rests on Model T24464 attach using (1) M6-1 knob and (1) M6-1 x 14 carriage bolt.
Do not pull by the cord as this may damage the wires inside. Turn machine ON, verify motor operation, and then turn machine OFF. The motor should run smoothly and without unusual problems or noises. Figure 13. Disconnecting power. -15- Models T24463/T24464 (Mfd. Since 02/16)
12. Quenches the workpiece as required to pre- machinery and cause seri- vent surface hardening or temper loss. ous personal injury. Keep loose clothing and long 13. Stops the bench grinder. hair away from moving machinery. -16- Models T24463/T24464 (Mfd. Since 02/16)
Wheel Selection DO NOT use this grinder with a liquid cool- ing system required for wet grinding wheel The Model T24463/T24464 only accepts Type 1 operations. The electrical system is not wheels with a ⁄ " bore. waterproof. Ignoring this warning can lead to electrocution or machine damage.
Always adjust the tool rest and spark deflec- tor after dressing or replacing the grind- ing wheel. Failure to do so could lead to workpiece kickback and injury. Figure 14. Tapping locations when performing a ring test. -18- Models T24463/T24464 (Mfd. Since 02/16)
—If the wheel appears to wobble, the grinder vibrates excessively, or any other unsafe condition appears with the new wheel, stop the grinder and refer to Troubleshooting on Page 22. Figure 15. Model T24464 wheel guard components. -19- Models T24463/T24464 (Mfd. Since 02/16)
Cast iron handle provides To reduce this risk, only install accessories stabilizing mass for better control. recommended for this machine by Grizzly. NOTICE Refer to our website or latest catalog for additional recommended accessories.
For optimum performance from your machine, plete details on how to properly dress a wheel. follow this maintenance schedule and refer to For Model T24463, refer to Page 18 for detailed any specific instructions given in this section. instructions. Routinely check the condition of the following...
2. Wheel too soft for the material being ground, select harder bond. 3. Wheel diameter too small. 3. Replace the wheel. 4. Bad wheel dress. 4. Dress the wheel. 5. Defective wheel bonding. 5. Consult manufacturer of grinding wheel. -22- Models T24463/T24464 (Mfd. Since 02/16)
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -23- Models T24463/T24464 (Mfd. Since 02/16)
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. -30-...
Page 33
Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times. _____ Yes _____No 10.
Page 34
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.