NEC PH1202HL1 User Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. Projector
  5. PH1202HL1
  6. User manual

NEC PH1202HL1 User Manual

Hide thumbs Also See for PH1202HL1:
Table of Contents

Advertisement

Quick Links

Download this manual
Projector
PH1202HL1
User's Manual
Model No.
NP-PH1202HL1

Advertisement

Table of Contents
loading

Related Manuals for NEC PH1202HL1

Summary of Contents for NEC PH1202HL1

  • Page 1 Projector PH1202HL1 User’s Manual Model No. NP-PH1202HL1...
  • Page 2 (3) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable points, errors or omissions, please contact us. (4) Notwithstanding article (3), NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.
  • Page 3 Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
  • Page 4 Important Information WARNING TO CALIFORNIA RESIDENTS: Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock.
  • Page 5 Important Information WARNING • Do not cover the lens with the lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap due to the heat emitted from the light output. • Do not place any objects, which are easily affected by heat, in front of the projector lens. Doing so could lead to the object melting from the heat that is emitted from the light output.
  • Page 6 Important Information • Handle the power cord carefully. A damaged or frayed power cord can cause electric shock or fire. - Do not use any power cord other than the one supplied with the projector. - Do not bend or tug the power cord excessively. - Do not place the power cord under the projector, or any heavy object.
  • Page 7 Important Information Remote Control Precautions • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • Do not short, heat, or take apart batteries. • Do not throw batteries into fire. •...
  • Page 8 Important Information Laser aperture and warning labels on the projector Laser aperture Non accessible Internal Laser Parameters Wavelength 462 nm Laser power for classification <220 mW Total internal laser power <56 W Divergence ±12 - 35° Mode of operation Negative modulation, due to frame rate 23 - 192Hz...
  • Page 9 Important Information About High Altitude mode • Using the projector at highlands can shorten the life of optical components such as the light module. About Copyright of original projected pictures: Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func- tions may raise concern about the infringement of copyrights which are protected by copyright law.
  • Page 10 Important Information Health precautions to users viewing 3D images Before viewing, be sure to read health care precautions that may be found in the user’s manual included with your 3D eyeglasses or your 3D compatible content such as Blu-ray Discs, video games, computer’s video files and the like. To avoid any adverse symptoms, heed the following: •...
  • Page 11 Important Information Clearance for Installing the Projector Allow ample clearance between the projector and its surroundings as shown below. The high temperature exhaust coming out of the device may be sucked into the device again. Avoid installing the projector in a place where air movement from the HVAC is directed at the projector. Heated air from the HVAC can be taken in by the projector's intake vent.

  • Page 12: Table Of Contents

    Table of Contents Important Information .................... i 1. Introduction ......................1 ❶ What’s in the Box? ......................1 ❷ Introduction to the Projector ...................2 Congratulations on Your Purchase of the Projector ..........2 General ........................2 Light source · Brightness ..................2 Installation .........................2 Videos ........................3 Network ........................3 Energy-saving ......................3 About this user’s manual ...................4...
  • Page 13 Table of Contents ❻ Freezing a Picture ......................29 ❼ Magnifying a Picture .....................30 ❽ Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE]......................31 Checking Energy-Saving Effect [CARBON METER] ..........33 ❾ Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] ....34 ❿ Preventing the Unauthorized Use of the Projector [SECURITY] ........37 ⓫...
  • Page 14 Table of Contents [VIDEO] ........................88 [3D SETTINGS] ......................90 Using the Lens Memory Function [LENS MEMORY] ..........91 ❺ Menu Descriptions & Functions [DISPLAY] ..............92 [PIP/PICTURE BY PICTURE] .................92 [GEOMETRIC CORRECTION] ................94 [EDGE BLENDING] ....................98 [MULTI SCREEN]....................99 ❻ Menu Descriptions & Functions [SETUP] ..............101 [MENU] .........................101 [INSTALLATION] ....................103 [CONTROL] ......................107...
  • Page 15 Table of Contents Download service ....................147 Operating Environment ..................147 ❷ Installing Software Program ..................148 Installation for Windows software ................148 ❸ Operating the Projector Via the LAN (Virtual Remote Tool) ........150 Connect the projector to a LAN................151 ❹ Controlling the Projector over a LAN (PC Control Utility Pro 4/Pro 5) ......153 9.

  • Page 16: Introduction

    (US: 7N080244) WARNING: Used by the service technician. Do not attempt to use by yourself as this is dangerous. • Important Infomation NEC Projector CD-ROM (7N8N6771) User’s manual (PDF) • Quick Setup Guide (For North (7N952401) America: 7N8N6781) • Security Sticker (Use this sticker when security password is set on.)

  • Page 17: ❷ Introduction To The Projector

    1. Introduction ❷ Introduction to the Projector This section introduces you to your new projector and describes the features and controls. Congratulations on Your Purchase of the Projector This projector is one of the very best projectors available today. The projector enables you to project precise images up to 500 inches across (measured diagonally) from your PC or Mac computer (desktop or notebook), VCR, Blu-ray player, or document camera.

  • Page 18: Videos

    1. Introduction Videos • Wide range of input/output terminals (HDMI, DisplayPort, HDBaseT, BNC, etc.) The projector is equipped with a variety of input/output terminals: HDMI, DisplayPort, HDBaseT, BNC (5-core), computer (analog), etc. The projector’s HDMI input/output terminals and DisplayPort input terminal support HDCP. HDBaseT, promoted and advanced by the HDBaseT Alliance, is a connection standard for home appliances.

  • Page 19: About This User's Manual

    1. Introduction About this user’s manual The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find an overview.

  • Page 20: ❸ Part Names Of The Projector

    1. Introduction ❸ Part Names of the Projector Front/Top The lens is sold separately. The description below is for when the NP-9LS16ZM1 lens is mounted. Terminals Controls/Indicator panel (→ page 8) (→ page 7) Remote Sensor (located on the front and the rear) (→...

  • Page 21: Rear

    1. Introduction Rear Intake vent Remote Sensor (located on the Takes in outside air to cool the unit. front and the rear) (→ page ix, 57, 142) (→ page 11) Rear LED (→ page 112) Exhaust vent Heated air is exhausted from here. Level Adjuster Handle (→...

  • Page 22: Controls/Indicator Panel

    1. Introduction Controls/Indicator Panel Input signal info: input terminal, entry list number, source name, horizontal frequency, vertical frequency 5 4 3 Error info: error code, error description 9. SHUTTER Button (→ page 28, 105) (light source) button (→ page 28) 11.

  • Page 23: Terminals Features

    1. Introduction Terminals Features 1. COMPUTER IN/ Component Input Terminal (Mini Connect the projector and the supplied remote control D-Sub 15 Pin) using a commercially available wired remote control (→ page 13, 129, 135, 169) cable. (→ page 11) 2. DisplayPort IN Terminal (DisplayPort 20 Pin) NOTE: (→...

  • Page 24: ❹ Part Names Of The Remote Control

    1. Introduction ❹ Part Names of the Remote Control 1. Infrared Transmitter 19. 3D REFORM Button (→ page 11) (→ page 34, 94) 2. Remote Jack 20. PIP/FREEZE Button Connect a commercially available (→ page 29, 58) remote cable here for wired opera- 21.

  • Page 25: Battery Installation

    1. Introduction Battery Installation 1. Press the catch and remove 2. Install new ones (AA). En- 3. Slip the cover back over the batteries until the battery cover. sure that you have the bat- it snaps into place. teries’ polarity (+/−) aligned NOTE: Do not mix different types of batteries or new correctly.

  • Page 26: Operating Range For Wireless Remote Control

    1. Introduction Operating Range for Wireless Remote Control 15 m/42.21 ft 15 m/42.21 ft Remote control 5° 30° 30° 30° Remote sensor on projector cabinet 30° 30° 30° 30° Remote control 15 m/42.21 ft 15 m/42.21 ft • The infrared signal operates by line-of-sight up to a distance of above meters and within a 60-degree angle of the remote sensor on the projector cabinet.

  • Page 27: Projecting An Image (Basic Operation)

    2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen. ❶ Flow of Projecting an Image Step 1 • Connecting your computer / Connecting the power cord (→ page 13) Step 2 •...

  • Page 28: ❷ Connecting Your Computer/Connecting The Power Cord

    2. Projecting an Image (Basic Operation) ❷ Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see “1. Con- necting a computer” on page 129. Connect the display output terminal (mini D-sub 15 pin) on the computer to the COMPUTER IN terminal on the projector with a commercially-available computer cable (with ferrite core) and then turn the knobs of the terminals to secure them.

  • Page 29: Using The Power Cord Fixing Metal

    2. Projecting an Image (Basic Operation) Using the Power Cord Fixing Metal To prevent the power cord from accidently removing from the AC IN of the projector, attach the power cord fixing metal. CAUTION • To prevent the power cord from coming loose, make sure that all the prongs of the power cord are fully inserted into the AC IN terminal of the projector before using the power cord fixing metal.

  • Page 30: ❸ Turning On The Projector

    2. Projecting an Image (Basic Operation) ❸ Turning on the Projector NOTE: • The projector has two power switches: A main power switch and a POWER button (POWER ON and OFF on the remote control) • Turning on the projector: 1. Press the main power switch to the ON position (I). The projector will go into standby mode. 2. Press the POWER button . The projector will become ready to use.

  • Page 31: Performing Lens Calibration

    2. Projecting an Image (Basic Operation) 2. Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator goes from a steady red light to a flashing blue light, and the picture is projected on the screen.

  • Page 32: Note On Startup Screen (Menu Language Select Screen)

    2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 29 menu languages. To select a menu language, follow these steps: 1.

  • Page 33: ❹ Selecting A Source

    2. Projecting an Image (Basic Operation) ❹ Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button for 1 second or longer. The projector will search for the available input source and display it.
  • Page 34 2. Projecting an Image (Basic Operation) Selecting Default Source You can set a source as the default source so that it will be displayed each time the projector is turned on. 1. Press the MENU button. The menu will be displayed. 2.

  • Page 35: ❺ Adjusting The Picture Size And Position

    2. Projecting an Image (Basic Operation) ❺ Adjusting the Picture Size and Position Use the lens shift dial, the level adjuster lever, the zoom lever/zoom ring and the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity. Adjusting the projector’s settings Adjusting the projected image’s vertical and horizontal [Level adjuster]...

  • Page 36: Adjustment Of The Projector's Settings (Level Adjusters)

    2. Projecting an Image (Basic Operation) • Perform the adjustment from behind or from the side of the projector. Adjusting from the front could expose your eyes to strong light which could injure them. CAUTION • Keep hands away from the lens mounting portion while the lens shift is in operation. Failure to do so could result in hands being pinched by the moving lens.

  • Page 37: Adjusting The Vertical Position Of A Projected Image (Lens Shift)

    2. Projecting an Image (Basic Operation) Adjusting the vertical position of a projected image (Lens shift) NOTE: • Shifting the lens to the maximum in two directions combined will cause the edges of the image to become dark or will cause some shadows. Adjusting with buttons on the cabinet 1. Press the LENS SHIFT/HOME POSITION button. The [LENS SHIFT] screen will be displayed. 2.
  • Page 38 2. Projecting an Image (Basic Operation) Adjusting with the remote control 1. Hold the CTL button and press the ECO/L-SHIFT button. The [LENS SHIFT] screen will be displayed. 2. Press the ▼▲◀ or ▶ button. Use the ▼▲◀▶ buttons to move the projected image. TIP: • The figure below shows the lens shift ranges (projection mode: desktop/front) of lens units NP-9LS08ZM1, NP-9LS12ZM1, NP- 9LS13ZM1, and NP-9LS16ZM1.

  • Page 39: Focus

    2. Projecting an Image (Basic Operation) Focus NOTE: • For lens unit NP-9LS08ZM1, both central and peripheral focus must be adjusted. Use theFOCUS +/−buttons to adjust the central focus. If the peripheral focus is off, contact your dealer to have them adjust it. 1. Press the FOCUS +/− button. • On the remote control, while pressing on the CTL button, press on VOL/FOCUS (+) or (−) button. The focus is adjusted.

  • Page 40: ❻ Optimizing Computer Signal Automatically

    2. Projecting an Image (Basic Operation) ❻ Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust When an image from HDMI IN, DisplayPort IN, BNC input terminal (analog RGB), COMPUTER IN, or HDBaseT is being projected, and the edge is cut off or the image quality is poor, this button can be used to automatically optimize the projection image on the screen.

  • Page 41: ❼ Turning Off The Projector

    2. Projecting an Image (Basic Operation) ❼ Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the POWER OFF button on the remote con- trol. The [POWER OFF / ARE YOU SURE ? / CARBON SAV- INGS- SESSION 0.000[g-CO2]] message will appear.
  • Page 42 2. Projecting an Image (Basic Operation) NOTE: • Do not unplug the power cord from the projector or from the power outlet while an image is being projected. Doing so could deteriorate the projector’s AC IN terminal or the power plug’s contact. To turn off the AC power supply when the projector is powered on, use the projector’s main power switch, a power strip equipped with a switch, or a breaker. • Do not turn off the main power switch or disconnect the AC power supply within 10 seconds of making adjustments or setting changes and closing the menu. Doing so can cause loss of adjustments and settings.

  • Page 43: Convenient Features

    3. Convenient Features ❶ Stopping projection 1. Press the SHUTTER button on the projector or on the remote On the projector On the remote control. SHUTTER indicator The light source will turn off and the light of the projector will temporarily go dark.

  • Page 44: ❹ Muting The Image (Av Mute)

    3. Convenient Features ❹ Muting the Image (AV Mute) Press the AV-MUTE button to turn off the image for a short period of time. Press again to restore the image. TIP: • The image will disappear but not the menu display. ❺ Turning Off the On-Screen Menu (On-Screen Mute) A press of the ON-SCREEN button on the remote control will hide the on-screen menu, the source display and other messages.

  • Page 45: ❼ Magnifying A Picture

    3. Convenient Features ❼ Magnifying a Picture You can magnify the picture up to four times. NOTE: • Depending on an input signal, the maximum magnification may be less than four times, or the function may be restricted. To do so: 1. Press the D-ZOOM (+) button to magnify the picture. 2. Press the ▲▼◀▶ button. The area of the magnified image will be moved 3.

  • Page 46: ❽ Changing Light Mode/Checking Energy-Saving Effect Using Light Mode

    3. Convenient Features ❽ Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE] When either [ECO1] or [ECO2] in [LIGHT MODE] is selected, motion noise of the projector is cut down by lowering brightness of its light source. By saving energy consumption, the CO emission from this projector can be reduced.
  • Page 47 3. Convenient Features NOTE: • The [LIGHT MODE] can be changed by using the menu. Select [SETUP] → [INSTALLATION] → [LIGHT MODE] → [LIGHT MODE]. • The light module used hours can be checked in [USAGE TIME]. Select [INFO.] → [USAGE TIME]. • After a lapse of 1 minute from when the projector displays a blue, black or logo screen, [LIGHT MODE] will automatically switch to [ECO]. By the automatic setting to [ECO], the projector will be automatically reset to the previous setting when it detects input signal. • If the projector is overheated in [NORMAL] mode, there may be a case the projector automatically lowers the brightness as a protective function. This is called “Forced ECO MODE”. When the projector is in the Forced ECO MODE, the picture brightness decreases slightly and the TEMP. indicator lights orange. At the same time the Thermometer symbol [ ] is displayed at the bot- tom right of the screen. When the projector comes back to normal temperature, the Forced ECO MODE is cancelled and the [LIGHT MODE] returns to [NORMAL] mode.

  • Page 48: Checking Energy-Saving Effect [Carbon Meter]

    3. Convenient Features Checking Energy-Saving Effect [CARBON METER] This feature will show energy-saving effect in terms of CO emission reduction (kg) when the projector’s [LIGHT MODE] is set to either [ECO1], [ECO2], or [LONG LIFE]. This feature is called as [CARBON METER]. There are two messages: [TOTAL CARBON SAVINGS] and [CARBON SAVINGS-SESSION].

  • Page 49: ❾ Correcting Horizontal And Vertical Keystone Distortion [Cornerstone]

    3. Convenient Features ❾ Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE] Use the [CORNERSTONE] feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side of the screen longer or shorter so that the projected image is rectangular. 1.
  • Page 50 3. Convenient Features 5. Press the ▼ button to align with the [CORNERSTONE] and then press the ENTER button. The drawing shows the upper left icon ( ) is selected. The screen will switch to the [CORNERSTONE] screen. NOTE: • When a [GEOMETRIC CORRECTION] function other than [CORNERSTONE] has been set up, the [CORNERSTONE] screen will not be displayed. When the screen is not displayed, either press the 3D REFORM button for 2 or more seconds, or run [RESET] in[GEOMETRIC CORRECTION] to clear the adjustment value of [GEOMETRIC CORRECTION].
  • Page 51 3. Convenient Features 13. Press the ◀ or ▶ button to highlight the [OK] and press the ENTER button. This completes the [CORNERSTONE] correction. • Returning to the [CORNERSTONE] screen, select [CANCEL] and press the ENTER button. NOTE: • Even when the projector is turned on, the last used correction values are applied. • Carry out either one of the following actions to clear the adjustment value of [CORNERSTONE].

  • Page 52: ❿ Preventing The Unauthorized Use Of The Projector [Security]

    3. Convenient Features ❿ Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro- jector cannot project an image.
  • Page 53 3. Convenient Features 7. Type in the same combination of ▲▼◀▶ buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1.
  • Page 54 3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [CONTROL] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed.

  • Page 55: ⓫ Projecting 3D Videos

    3. Convenient Features ⓫ Projecting 3D videos This projector supports DLP-Link glasses and 3D emitter. CAUTION Health precautions Before use, please make sure to read any health precautions that may be stated in the operating manuals enclosed with the 3D eyewear and 3D video software (Blu-ray player, games, computer animation files, etc.). Please take note of the following in order to avoid adverse health effects.
  • Page 56 3. Convenient Features (3)Use the ▶ button to select [3D SETTINGS]. The [3D SETTINGS] screen will be displayed. (4)Use the ▼ button to align the cursor with [FORMAT], then press ENTER. The [FORMAT] screen will be displayed. (5)Use the ▼/▲ buttons to align the cursor at one among format options, then press ENTER for setting it up. The display will return to the [3D SETTINGS] screen.

  • Page 57: When Videos Cannot Be Viewed In 3D

    3. Convenient Features When videos cannot be viewed in 3D Please check the following points when videos cannot be viewed in 3D. Please also read the operating manual attached to the 3D eyewear. Possible reasons Solutions The selected signal does not support 3D output. Please change the video signal input to one that supports 3D.

  • Page 58: ⓬ Controlling The Projector By Using An Http Browser

    3. Convenient Features ⓬ Controlling the Projector by Using an HTTP Browser Overview The HTTP Server function provides settings and operations for: 1. Setting for wired network (NETWORK SETTINGS) To use wired LAN connection, connect the projector to the computer with a commercially available LAN cable. (→ page 138) 2.
  • Page 59 IP address of the projector has been set in the “HOSTS” file of the computer being used. Example 1: When the host name of the projector has been set to “pj.nec.co.jp”, access is gained to the network setting by specifying http://pj.nec.co.jp/index.html...
  • Page 60 3. Convenient Features PICTURE: Controls the video adjustment of the projector. BRIGHTNESS ▲ ..Increases the brightness adjustment value. BRIGHTNESS ▼ ..Decreases the brightness adjustment value. CONTRAST ▲ ..Increases the contrast adjustment value. CONTRAST ▼ ..Decreases the contrast adjustment value. COLOR ▲...
  • Page 61 3. Convenient Features NETWORK SETTINGS • SETTINGS WIRED SETTING Set for wired LAN. APPLY Apply your settings to wired LAN. PROFILE 1/PROFILE 2 Two settings can be set for wired LAN connection. Select PROFILE 1 or PROFILE 2. DISABLE Turn off wired LAN connection DHCP ON Automatically assign IP address, subnet mask, and gateway to the projector from your DHCP server.
  • Page 62 3. Convenient Features • NAME PROJECTOR NAME Enter a name for your projector so that your computer can identify the projector. A projector name must be 16 characters or less. TIP: Projector name will not be affected even when [RESET] is done from the menu. HOST NAME Enter the hostname of the network connected to the projector.
  • Page 63 3. Convenient Features • NETWORK SERVICE PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password. However, if you forget your password, consult with your dealer. HTTP PASSWORD Set a password for HTTP server. A password must be 10 characters or less. When a password is set up, you will be prompted for your user name (arbitrary) and password during LOGON.

  • Page 64: ⓭ Storing Changes For Lens Shift, Zoom, And Focus [Lens Memory]

    3. Convenient Features ⓭ Storing Changes for Lens Shift, Zoom, and Focus [LENS MEMORY] The adjusted values can be stored in projector memory when using the LENS SHIFT, ZOOM and FOCUS buttons of the projector. Adjusted values can be applied to the signal you selected. This will eliminate the need to adjust lens shift, focus, and zoom at the time of source selection.
  • Page 65 3. Convenient Features The [REF. LENS MEMORY] screen will be displayed. 5. Make sure [PROFILE] is highlighted, then press the ENTER button. The [PROFILE] selection screen appears. 6. Press the ▼/▲ buttons to select the [PROFILE] number, then press the ENTER button. Return to the [REF.

  • Page 66: To Call Up Your Adjusted Values From [Ref. Lens Memory]

    3. Convenient Features 9. Press the MENU button. The menu will be closed. TIP: • To store adjusted values for each input source, use the Lens Memory function. (→ page 91) To call up your adjusted values from [REF. LENS MEMORY]: 1. Press the MENU button. The menu will be displayed. 2. Press the ▶ button to select [SETUP] and press the ENTER button. 3.
  • Page 67 3. Convenient Features Return to the [REF. LENS MEMORY] settings screen. 7. Select [MOVE] and press the ENTER button. The lens will shift based on the adjusted values stored in the selected [PROFILE]. 8. Press the ◀ button to select and [YES] and press the ENTER button. The adjusted values will be applied to the current signal.
  • Page 68 3. Convenient Features TIP: To call up the adjusted values from [LENS MEMORY]: 1. From the menu, select [ADJUST] → [LENS MEMORY] → [MOVE] and press the ENTER button. The confirmation screen will be displayed. 2. Press the ◀ button to select and [YES] and press the ENTER button. During projection, if the adjusted values for an input signal have been saved, the lens will shift.

  • Page 69: Multi-Screen Projection

    4. Multi-Screen Projection ❶ Things that can be done using multi-screen projection This projector can be used singly or arranged in multiple units for multi-screen projection. We will introduce an example using two projection screens here. Case 1 Using a single projector to project two types of videos at the same time [PIP/PICTURE BY PICTURE] Case 2 Using four projectors (resolution: FULL HD) to project video with a resolution of 3840 ×...

  • Page 70: Case 2. Using Four Projectors (Resolution: Full Hd) To Project Videos With A Resolution Of 3840 × 2160 Pixels [Tiling]

    4. Multi-Screen Projection Case 2. Using four projectors (resolution: FULL HD) to project videos with a resolution of 3840 × 2160 pixels [TILING] Connection example and projection image On-screen menu operations 1 Four similar videos are displayed when four projectors are projected. Please request the dealer to adjust the projection position of each projector.
  • Page 71 4. Multi-Screen Projection 2 Operate the on-screen menu using the four respective projectors to divide the image into four portions. Display [DISPLAY] → [MULTI SCREEN] → [PICTURE SETTING] Screen in the on-screen menu and select [TIL- ING]. (1)In the screen for setting the number of horizontal units, select [2 UNITS]. (number of units in the horizontal direc- tion) (2)In the screen for setting the number of vertical units, select [2 UNITS].

  • Page 72: Things To Note When Installing Projectors

    4. Multi-Screen Projection Things to note when installing projectors • Leave 60 cm/23.6" or over space between the projectors when projectors are installed side by side, so that the intake vents of the projectors are not obstructed. In addition, leave a space of at least 30 cm/11.8" between the intake vent and the wall and at least 70 cm/27.6"...

  • Page 73: ❷ Displaying Two Pictures At The Same Time

    4. Multi-Screen Projection ❷ Displaying Two Pictures at the Same Time The projector has a feature that allows you to view two different signals simultaneously. You have two modes: picture in picture (PIP) mode and picture by picture (PICTURE BY PICTURE) mode. The projection video in the first screen display is known as the main display while the projection video that is called out subsequently is known as the sub-display.

  • Page 74: Projecting Two Screens

    4. Multi-Screen Projection Projecting two screens 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PICTURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2. Select [SUB INPUT] using the ▼/▲ buttons, and press the ENTER button. This displays the [SUB INPUT] screen.

  • Page 75: Switching The Main Display With The Sub-Display And Vice Versa

    4. Multi-Screen Projection Switching the main display with the sub-display and vice versa 1. Press the MENU button to display the on-screen menu and select [DISPLAY] → [PIP/PICTURE BY PICTURE]. This displays the [PIP/PICTURE BY PICTURE] screen in the on-screen menu. 2.

  • Page 76: Restrictions

    4. Multi-Screen Projection Restrictions • The following operations are enabled only for the main display. • Visual adjustments • Video magnification / demaginification using the partial D-ZOOM/ZOOM +/− buttons. However, magnification / demaginification is up to the boundary set in [PICTURE BY PICTURE]. •...

  • Page 77: ❸ Displaying A Picture Using [Edge Blending]

    4. Multi-Screen Projection ❸ Displaying a Picture Using [EDGE BLENDING] A high resolution video can be projected on an even bigger screen by combining multiple projectors on the left, right, top and bottom. This projector is equipped with an “EDGE BLENDING Function” that makes the edges (boundaries) of the projection screen indistinguishable.

  • Page 78: Setting The Overlap Of Projection Screens

    4. Multi-Screen Projection Preparation: • Turn on the projector and display a signal. • When performing settings or adjustments using the remote control, enable the [CONTROL ID] so as not to activate the other projectors. (→ page 113) Setting the overlap of projection screens ①...
  • Page 79 4. Multi-Screen Projection 5. Select [CONTROL] → [ON] and press the ENTER button. Each [TOP], [BOTTOM], [LEFT], [RIGHT], and [BLACK LEVEL] has its own [CONTROL], [MARKER], [RANGE], and [POSITION]. • For Projector A, set the [CONTROL] for the [TOP], [LEFT] and[BOTTOM] to [OFF]. Similarly for Projector B, set the [CONTROL] for the [TOP], [RIGHT] and [BOTTOM] to [OFF].
  • Page 80 4. Multi-Screen Projection 1 Adjust [RANGE]. Use the ◀ or ▶ button to adjust the overlapped area. TIP: • Adjust to overlap one projector’ marker with the other projector’s marker. 2 Adjust [POSITION]. Use the ◀ or ▶ button to align one edge with the other edge of overlapped images. TIP: • When displaying a signal with a different resolution, perform the Edge Blending function from the start.

  • Page 81: Black Level Adjustment

    4. Multi-Screen Projection Black Level Adjustment This adjusts the black level of the overlapping area and the non-overlapping area of the multi-screen (EDGE BLENDING). Adjust the brightness level if you feel the difference is too large. NOTE: This function is enabled only when [MODE] is turned on. Adjustable area varies depending on what combination of [TOP], [BOTTOM], [LEFT] and [RIGHT] are turned on. Example: Adjusting the Black Level when placing two projectors side by side Width of overlap Adjust [CENTER] Adjust [CENTER]...
  • Page 82 4. Multi-Screen Projection 9-segmented portions for Black Level adjustment The center projector This function adjusts the brightness level of 9-segmented portions for the center projector and 4-segmented portions for the left bottom projector as shown below. TOP-CENTER TOP-LEFT TOP-RIGHT CENTER- LEFT CENTER-RIGHT CENTER...

  • Page 83: Using On-Screen Menu

    5. Using On-Screen Menu ❶ Using the Menus NOTE: The on-screen menu may not be displayed correctly depending on input signal and the projector setting. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, ▲▼, ◀▶...

  • Page 84: Menu Elements

    5. Using On-Screen Menu Menu Elements Slide bar Solid triangle Available buttons Source Menu mode Highlight Radio button LIGHT MODE symbol Off Timer remaining time Thermometer symbol Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight ......Indicates the selected menu or item.

  • Page 85: ❷ List Of Menu Items

    5. Using On-Screen Menu ❷ List of Menu Items • Basic menu items are indicated by shaded area. Some menu items are not available depending on the input source. Menu Item Default Options HDMI DisplayPort BNC(CV) BNC(Y/C) INPUT COMPUTER HDBaseT SLOT ENTRY LIST TEST PATTERN...
  • Page 86 5. Using On-Screen Menu Menu Item Default Options OFF, HDMI, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER, SUB INPUT HDBaseT, SLOT MODE PIP, PICTURE BY PICTURE PICTURE SWAP OFF, ON PIP/PICTURE START POSITION TOP-LEFT TOP-LEFT, TOP-RIGHT, BOTTOM-LEFT, BOTTOM-RIGHT BY PICTURE HORIZONTAL POSITION PIP SETTING VERTICAL POSITION SIZE...
  • Page 87 5. Using On-Screen Menu Menu Item Default Options ENGLISH, DEUTSCH, FRANÇAIS, ITALIANO, ESPAÑOL, SVENSKA, 日本語 DANSK, PORTUGUÊS, ČEŠTINA, MAGYAR, POLSKI, NEDERLANDS, SUOMI LANGUAGE ENGLISH , Ελληνικά, 中文, 한국어 NORSK, TÜRKÇE, РУССКИЙ, ROMÂNĂ, HRVATSKA, БЪЛГАРСКИ, INDONESIA, हिन् द ी, ไทย, , 繁體中文 COLOR SELECT COLOR COLOR, MONOCHROME...
  • Page 88 5. Using On-Screen Menu Menu Item Default Options MENU MODE ADVANCED ADVANCED, BASIC NOT SAVE SETTING VALUES OFF, ON ADMINISTRA- TOR MODE NEW PASSWORD CONFIRM PASSWORD ENABLE OFF, ON ACTIVE OFF, ON SUN, MON, TUE, WED, THU, FRI, SAT, MON-FRI, MON-SAT, EVERY TIME FUNCTION POWER, INPUT, LIGHT MODE...
  • Page 89 5. Using On-Screen Menu Menu Item Default Options PROFILES DISABLE, PROFILE 1, PROFILE 2 DHCP OFF, ON IP ADDRESS 192.168.0.10 SUBNET MASK 255.255.255.0 WIRED LAN GATEWAY 192.168.0.1 AUTO DNS OFF, ON DNS CONFIGURATION RECONNECT PROJECTOR NAME PROJECTOR NAME PH1202HL Series HOST NAME necpj DOMAIN...
  • Page 90 5. Using On-Screen Menu Menu Item Default Options LIGHT HOURS USED USAGE TIME FILTER HOURS USED TOTAL CARBON SAVINGS INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SOURCE(1) SYNC TYPE SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO. SIGNAL TYPE VIDEO TYPE BIT DEPTH SOURCE(2) VIDEO LEVEL...

  • Page 91: ❸ Menu Descriptions & Functions [Input]

    5. Using On-Screen Menu ❸ Menu Descriptions & Functions [INPUT] HDMI This projects the video of the device connected to the HDMI IN terminal. DisplayPort This projects the video of the device connected to the Display Port IN terminal. This projects the video of the device connected to the video input terminal. (This projects the analog RGB signal or component signal.) BNC(CV) This projects the video of the device connected to the BNC (CV) video input terminal.
  • Page 92 5. Using On-Screen Menu Using the Entry List When you save [IMAGE OPTIONS] and [LENS MEMORY], the adjusted values of the signal are automatically saved to the projector’s [ENTRY LIST].When needed, the stored signal adjusted values can be accessed from the [ENTRY LIST]. However, only up to 100 patterns can be registered in the Entry List.
  • Page 93 5. Using On-Screen Menu Entering the currently projected signal into the Entry List [STORE] 1. Press the ▲ or ▼ button to select any number. 2. Press the ◀ or ▶ button to select [STORE] and press the ENTER button. Calling up a signal from the Entry List [LOAD] Press the ▲...
  • Page 94 5. Using On-Screen Menu Cutting a signal from the Entry List [CUT] 1. Press the ▲ or ▼ button to select a signal you wish to delete. 2. Press the ◀, ▶, ▲, or ▼ button to select [CUT] and press the ENTER button. The signal will be deleted from the Entry List and the deleted signal will be displayed on the clipboard at the bottom of the Entry List.

  • Page 95: ❹ Menu Descriptions & Functions [Adjust]

    5. Using On-Screen Menu ❹ Menu Descriptions & Functions [ADJUST] [PICTURE] [MODE] This function allows you to determine how to save settings for [DETAIL SETTINGS] of [PRESET] for each input. STANDARD .... Saves settings for each item of [PRESET] (Preset 1 through 7) PROFESSIONAL ..
  • Page 96 5. Using On-Screen Menu [DETAIL SETTINGS] [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT ..
  • Page 97 5. Using On-Screen Menu Adjusting Color Temperature [COLOR TEMPERATURE] This option allows you to select the color temperature of your choice. A value between 5000 K and 10500 K can be set in 100 K units. NOTE: When [PRESENTATION] or [HIGH-BRIGHT] is selected in [REFERENCE], this function is not available. Adjusting Brightness and Contrast [DYNAMIC CONTRAST] Select [MOTION IMAGE] or [STILL IMAGE] depending on the picture you wish to project, and the contrast ration will be adjusted to the optimum value.
  • Page 98 5. Using On-Screen Menu [HUE] Varies the color level from +/− green to +/− blue. The red level is used as reference. Input signal CONTRAST BRIGHTNESS SHARPNESS COLOR RGB system of “COMPUTER/ DisplayPort/HDMI/HDBaseT” COMPONENT system of “COMPUTER/ DisplayPort/HDMI/HDBaseT” Composite Video/S-Video Yes = Adjustable, No = Not adjustable NOTE: • When [TEST PATTERN] is displayed, [CONTRAST], [BRIGHTNESS], [SHARPNESS], [COLOR] and [HUE] cannot be adjusted.

  • Page 99: [Image Options]

    5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK ....Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image.
  • Page 100 5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. • An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. • The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the current signal.
  • Page 101 5. Using On-Screen Menu Selecting the Aspect Ratio [ASPECT RATIO] Use this function to select the screen’s vertical:horizontal aspect ratio. Select the screen type (4:3 screen, 16:9 screen or 16:10 screen) at the screen setting before setting the aspect ratio. (→...
  • Page 102 5. Using On-Screen Menu Options Function NATIVE The projector displays the current image in its true resolution when the incoming computer signal has a lower or higher resolution than the projector’s native resolution. (→ page 164) When the incoming computer signal has a higher resolution than the projector's native resolution, the center of an image will be displayed.

  • Page 103: [Video]

    5. Using On-Screen Menu [VIDEO] Using Noise Reduction [NOISE REDUCTION] When projecting a video image, you can use the [NOISE REDUCTION] function to reduce the screen noise (roughness and distortion). This device is equipped with three types of noise reduction functions. Select the function according to the type of noise.
  • Page 104 5. Using On-Screen Menu [SIGNAL TYPE] Selection of RGB and component signals. Normally, this is set to [AUTO]. Please change the setting if the color of the image remains unnatural. AUTO ..... Automatically distinguishes RGB and component signals. RGB ....... Switches to the RGB input. COMPONENT ..

  • Page 105: [3D Settings]

    5. Using On-Screen Menu [3D SETTINGS] Please refer to “3-11 Projecting 3D videos” (→ page 40) for the operation. STEREO VIEWER Adjusting the settings for projecting a 3D picture with one or multiple projectors. For 3D glasses right-eye and left-eye settings, select [STEREO VIEWER].

  • Page 106: Using The Lens Memory Function [Lens Memory]

    5. Using On-Screen Menu Using the Lens Memory Function [LENS MEMORY] This function serves to store the adjusted values for each input signal when using the LENS SHIFT, ZOOM and FO- CUS buttons of the projector. Adjusted values can be applied to the signal you selected. This will eliminate the need to adjust lens shift, focus, and zoom at the time of source selection.

  • Page 107: ❺ Menu Descriptions & Functions [Display]

    5. Using On-Screen Menu ❺ Menu Descriptions & Functions [DISPLAY] [PIP/PICTURE BY PICTURE] SUB INPUT Select the input signal to be displayed in the sub-display. Please refer to “4-2 Displaying Two Pictures at the Same Time” (→ page 58) for details on the operation. MODE Select either PIP or PICTURE BY PICTURE when switching to 2-screen display.
  • Page 108 5. Using On-Screen Menu TIP: The horizontal position and vertical position are the amount of movement from the reference points. For example, when TOP-LEFT is adjusted, the position is displayed with the same amount of movement even if displayed with other starting positions. The maximum amount of movement is half the resolution of the projector. Reference point Adjust using the horizon- Reference point tal position Adjust using the vertical position TOP-LEFT TOP-RIGHT BOTTOM-LEFT...

  • Page 109: [Geometric Correction]

    5. Using On-Screen Menu [GEOMETRIC CORRECTION] KEYSTONE Display the trapezoid correction screen and adjust the trapezoidal distortion of the projection screen. To display the [KEYSTONE] screen, select [DISPLAY] → [GEOMETRIC CORRECTION] → [KEYSTONE] in the on- screen menu. The [GEOMETRIC CORRECTION] screen can also be displayed by pressing the 3D REFORM button on the projector or on the remote control.
  • Page 110 5. Using On-Screen Menu CORNERSTONE Display the 4-point correction screen and adjust the trapezoidal distortion of the projection screen. Please refer to “Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]” (→ page 34) for details on the operation. HORIZONTAL CORNER/VERTICAL CORNER Distortion correction for corner projection such as wall surfaces.
  • Page 111 5. Using On-Screen Menu Adjustment method 1. Align the cursor with the [HORIZONTAL CORNER] or [VERTICAL CORNER] of the [GEOMETRIC CORREC- TION] menu and then press the ENTER button. • The adjustment screen will be displayed. 2. Press the ▼▲◀▶ buttons to align the cursor (yellow box) with the target adjustment point and then press the ENTER button.
  • Page 112 5. Using On-Screen Menu PINCUSHION Adjust the curve distortion of the projection screen. TOP ......Adjust the curve distortion of the upper edge of the projection screen. BOTTOM ....Adjust the curve distortion of the lower edge of the projection screen.

  • Page 113: [Edge Blending]

    5. Using On-Screen Menu [EDGE BLENDING] This adjusts the edges (boundaries) of the projection screen when projecting high resolution videos using a combina- tion of several projectors in the up, down, left and right positions. MODE This enables or disables the EDGE BLENDING function. When MODE is set to ON, the TOP, BOTTOM, LEFT, RIGHT and BLACK LEVEL settings can be adjusted.

  • Page 114: [Multi Screen]

    5. Using On-Screen Menu [MULTI SCREEN] WHITE BALANCE This adjusts the white balance for each projector when projecting using a combination of several projectors. This can be adjusted when [MODE] is set to [ON]. BRIGHTNESS W, BRIGHTNESS R, BRIGHTNESS G, BRIGHTNESS B ......
  • Page 115 5. Using On-Screen Menu Conditions for using tiling • All the projectors need to fulfil the following conditions. • The panel size must be the same • The projection screen size must be the same • The left and right ends or top and bottom ends of the projection screen must be consistent. •...

  • Page 116: ❻ Menu Descriptions & Functions [Setup]

    5. Using On-Screen Menu ❻ Menu Descriptions & Functions [SETUP] [MENU] Selecting Menu Language [LANGUAGE] You can choose one of 29 languages for on-screen instructions. NOTE: Your setting will not be affected even when [RESET] is done from the menu. Selecting Menu Color [COLOR SELECT] You can choose between two options for menu color: COLOR and MONOCHROME. Turning On / Off Source Display [INPUT DISPLAY] This option turns on or off input name display such as HDMI, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER, HDBaseT to be displayed on the top right of the screen.
  • Page 117 5. Using On-Screen Menu [3D CAUTION MESSAGE] This selects whether to display a caution message or not when switching to a 3D video. The default condition when shipped from the factory is ON. OFF ......The 3D caution message screen will not be displayed. ON ......

  • Page 118: [Installation]

    5. Using On-Screen Menu [INSTALLATION] Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection. NOTE: • Please consult the dealer if you require special installation services e.g. when mounting the projector to a ceiling. Never install the projector on your own. This may result in the projector falling down and causing injury to people. DESKTOP FRONT CEILING REAR DESKTOP REAR...
  • Page 119 5. Using On-Screen Menu Selecting Aspect Ratio and Position for Screen [SCREEN TYPE] Screen type Sets the aspect ratio of the projection screen. FREE The ratio of panel is selected. Select this when projecting multi-screen and 17:9 screen (2K). 4:3 screen For a screen with a 4:3 aspect ratio 16:9 screen For a screen with a 16:9 aspect ratio...
  • Page 120 5. Using On-Screen Menu [LIGHT MODE] Adjusting the energy savings settings and the brightness of each projector in multi-screen projection. For energy savings settings, see page “3-8. Changing LIGHT MODE/Checking Energy-Saving Effect Using LIGHT MODE [LIGHT MODE]”. LIGHT MODE NORMAL The light module luminance (brightness) will become 100% and the screen will turn bright.
  • Page 121 5. Using On-Screen Menu [REF. WHITE BALANCE] This feature allows you to adjust the white balance for all signals. The white and black levels of the signal are adjusted for optimum color reproduction. Uniformity is also adjusted when the redness (R) and blueness (B) of the white color in the screen’s horizontal (left/ right) direction are uneven.

  • Page 122: [Control]

    5. Using On-Screen Menu [CONTROL] TOOLS ADMINISTRATOR MODE This allows you to select MENU MODE, save settings, and set a password for the administrator mode. MENU MODE Select either [BASIC] or [ADVANCED] menu. — (→ page 70) Placing a check mark will not save your projector settings. NOT SAVE SETTING —...
  • Page 123 5. Using On-Screen Menu PROGRAM TIMER This option turns on/standby the projector and changes video signals, and selects ECO mode automatically at a specified time. NOTE: • Before using [PROGRAM TIMER], make sure that the [DATE AND TIME] feature is set. (→ page 111) Make sure that the projector is in the standby condition with the POWER cord connected. The projector has a built-in clock. The clock will keep working for about two weeks after the main power is turned off. If the main power is not supplied to the projector for two weeks or more, it requires to set [DATE AND TIME SETTINGS] feature again.
  • Page 124 5. Using On-Screen Menu TIME ...... Set the time to execute the program. Enter time in 24-hour format. FUNCTION ..... Select a function to be executed. Selecting [POWER] will allow you to turn on or off the projector by setting [ADVANCED SETTINGS].
  • Page 125 5. Using On-Screen Menu Activating the program timer 1. Select [ENABLE] on the [PROGRAM TIMER] screen and press the ENTER button. The selection screen will be displayed. 2. Press the ▼ button to align the cursor with [ON] and then press the ENTER button. Return to the [PROGRAM TIMER] screen.
  • Page 126 5. Using On-Screen Menu DATE AND TIME SETTINGS You can set the current time, month, date, and year. NOTE: The projector has a built-in clock. The clock will keep working for about 2 weeks after the main power is turned off. If the main power is off for 2 weeks or more, the built-in clock will cease.
  • Page 127 5. Using On-Screen Menu Disabling the Cabinet Buttons [CONTROL PANEL LOCK] This option turns on or off the CONTROL PANEL LOCK function. NOTE: • How to cancel the [CONTROL PANEL LOCK] When the [CONTROL PANEL LOCK] is set to [ON], press either the KEY LOCK button on the projector over 1 second or the SOURCE button over 10 seconds to cancel the [CONTROL PANEL LOCK]. TIP: • When the [CONTROL PANEL LOCK] is turned on, a key lock icon [ ] will be displayed at the bottom right of the menu. • This CONTROL PANEL LOCK does not affect the remote control functions. [NOTIFICATION SETTINGS] This setting is to enable/disable the notification by the buzzer and rear LED. REAR LED [REAR LED] is deactivated.
  • Page 128 5. Using On-Screen Menu Setting ID to the Projector [CONTROL ID] You can operate multiple projectors separately and independently with the single remote control that has the CONTROL ID function. If you assign the same ID to all the projectors, you can conveniently operate all the projectors together using the single remote control.
  • Page 129 5. Using On-Screen Menu Turning On or Off Remote Sensor [REMOTE SENSOR] This option determines which remote sensor on the projector is enabled in wireless mode. The options are: FRONT/BACK, FRONT, BACK, and HDBaseT. NOTE: • The remote control of the projector will not be able to receive signals if the power supply of the HDBaseT transmission device connected to the projector is switched on when this has been set to “HDBaseT”. TIP: • If the remote control system does not function when direct sunlight or strong illumination strikes the remote control sensor of the projector, change another option.

  • Page 130: [Network Settings]

    5. Using On-Screen Menu [NETWORK SETTINGS] Important: • Consult with your network administrator about these settings. • When using a wired LAN connection, connect a LAN cable (Ethernet cable) to the LAN port (RJ-45) of the projector. (→ page 138) TIP: The network settings you make will not be affected even when [RESET] is done from the menu. Hints on How to Set Up LAN Connection To set up the projector for a LAN connection: Select [WIRED LAN] → [PROFILES] → [PROFILE 1] or [PROFILE 2]. Two settings can be set for wired LAN.
  • Page 131 5. Using On-Screen Menu WIRED LAN PROFILES • The settings for using the built-in Ethernet/HDBaseT port in the — projector can be recorded in the projector memory in two ways. • Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] and the other options.
  • Page 132 5. Using On-Screen Menu PROJECTOR NAME PROJECTOR NAME Set a unique projector name. Up to 16 alphanu- meric characters and symbols DOMAIN Set a host name and domain name of the projector. HOST NAME Set a host name of the projector. Up to 15 alphanumeric characters DOMAIN NAME...
  • Page 133 5. Using On-Screen Menu ALERT MAIL ALERT MAIL This option will notify your computer of error messages via e-mail — when using wireless or wired LAN. Placing a checkmark will turn on the Alert Mail feature. Clearing a checkmark will turn off the Alert Mail feature. Sample of a message to be sent from the projector: Subject: [Projector] Projector Information THE COOLING FAN HAS STOPPED.
  • Page 134 5. Using On-Screen Menu NETWORK SERVICE HTTP SERVER Set a password for your HTTP server. Up to 10 alphanumeric characters PJLink This option allows you to set a password when you use the Up to 32 alphanumeric PJLink feature. characters NOTE: • Do not forget your password. However, if you forget your password, consult with your dealer.

  • Page 135: [Source Options]

    5. Using On-Screen Menu [SOURCE OPTIONS] Setting Auto Adjust [AUTO ADJUST] This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for noise and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE]. OFF ......
  • Page 136 5. Using On-Screen Menu [SEAMLESS SWITCHING] When the input connector is switched, the image displayed before switching is held to switch to the new image without a break due to absence of a signal. Setting Closed Caption [CLOSED CAPTION] This option sets several closed caption modes that allow text to be superimposed on the projected image of Video or S-Video.

  • Page 137: [Power Options]

    5. Using On-Screen Menu [POWER OPTIONS] Selecting Power-saving in [STANDBY MODE] Setting the power consumption in the standby mode. NORMAL ....In the standby mode, the power consumption of the projector is minimized. In the standby mode, the POWER indicator lights up in red while the STATUS indicator will go off. • When set to [NORMAL], the following terminals and functions will be disabled. HDMI OUT terminals, Ethernet/HDBaseT port, LAN function, mail notification function HDBaseT STANDBY...
  • Page 138 5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON SELECT] If set to [HDBaseT STANDBY], the projector automatically detects the synchronizing signal input from the following selected terminals and projects the picture accordingly: Computer, HDMI, DisplayPort, HDBaseT, and SLOT. OFF ......

  • Page 139: Returning To Factory Default [Reset]

    5. Using On-Screen Menu Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels. The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS], [AS- PECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].

  • Page 140: ❼ Menu Descriptions & Functions [Info.]

    5. Using On-Screen Menu ❼ Menu Descriptions & Functions [INFO.] Displays the status of the current signal and light module usage. This item has nine pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LIGHT HOURS USED] (H) [FILTER HOURS USED] (H) [TOTAL CARBON SAVINGS] (kg-CO2) •...

  • Page 141: [Source(2)]

    5. Using On-Screen Menu [SOURCE(2)] SIGNAL TYPE VIDEO TYPE BIT DEPTH VIDEO LEVEL LINK RATE LINK LANE 3D FORMAT [SOURCE(3)] INPUT TERMINAL RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY SYNC TYPE SYNC POLARITY SCAN TYPE SOURCE NAME ENTRY NO. [SOURCE(4)] SIGNAL TYPE VIDEO TYPE BIT DEPTH VIDEO LEVEL...

  • Page 142: [Wired Lan]

    5. Using On-Screen Menu [WIRED LAN] IP ADDRESS SUBNET MASK GATEWAY MAC ADDRESS [VERSION(1)] FIRMWARE DATA SUB-CPU [VERSION(2)] FIRMWARE3...

  • Page 143: [Others]

    5. Using On-Screen Menu [OTHERS] DATE TIME PROJECTOR NAME MODEL NO. SERIAL NUMBER CONTROL ID (when [CONTROL ID] is set) [CONDITIONS] INTAKE TEMPERATURE EXHAUST TEMPERATURE ATMOSPHERIC PRESSURE [HDBaseT] SIGNAL QUALITY OPERATION MODE LINK STATUS HDMI STATUS...

  • Page 144: Connecting To Other Equipment

    6. Connecting to Other Equipment ❶ Connecting a computer A computer cable, BNC cable (5-core type), HDMI cable, or a DisplayPort cable can be used to connect to a computer. The connection cable is not enclosed with the projector. Please get ready a suitable cable for the connection. Analog RGB signal connection •...

  • Page 145: Digital Rgb Signal Connection

    6. Installation and Connections Digital RGB signal connection • Connect a commercially available HDMI cable between the computer’s HDMI output terminal and the projector’s HDMI IN terminal. • Connect a commercially available DisplayPort cable between the computer’s DisplayPort output terminal and the projector’s DisplayPort IN terminal.
  • Page 146 6. Installation and Connections Cautions when connecting an HDMI cable • Use a certified High Speed HDMI Cable or High Speed HDMI Cable with Ethernet. ® ® Cautions when connecting a DisplayPort cable • Use a certified DisplayPort cable. • Depending on the computer, some time may be required until the image is displayed.
  • Page 147 6. Installation and Connections Cautions when using a DVI signal • When the computer has a DVI output terminal, use a commercially available converter cable to connect the com- puter to the projector’s HDMI IN terminal (only digital video signals can be input). HDMI IN NOTE: When Viewing a DVI Digital Signal • Turn off the power of the computer and projector before connecting devices.

  • Page 148: ❷ Connecting An External Monitor

    6. Installation and Connections ❷ Connecting an External Monitor HDMI IN HDMI OUT HDMI cable (not supplied) HDMI cable (not supplied) HDMI IN As shown in the figure, when the projector is connected to a computer, the same content from the HDMI input signal is displayed on the monitor for confirmation.

  • Page 149: ❸ Connecting Your Blu-Ray Player Or Other Av Equipment

    6. Installation and Connections ❸ Connecting Your Blu-ray Player or Other AV Equipment Component video signal/S-video signal connection BNC （Y） BNC （C） BNC （CV） If the signal is a composite video signal If the signal is an S-video signal BNC cable (not supplied) BNC cable (not supplied) Audio equipment •...

  • Page 150: Connecting Component Input

    6. Installation and Connections Connecting Component Input Connect the Blu-ray player’s audio to the audio device. COMPUTER IN 15-pin - to - RCA (female) × 3 cable adapter BNC (male) - to - RCA (male) conversion (ADP-CV1E) cable × 3 (sold commercially) Component video RCA ×...

  • Page 151: Connecting Hdmi Input

    6. Installation and Connections Connecting HDMI Input You can connect the HDMI output of your Blu-ray player, hard disk player, or notebook type PC to the HDMI IN terminal of your projector. HDMI IN HDMI cable (not supplied) Use High Speed HDMI Cable.

  • Page 152: ❹ Connecting A Document Camera

    6. Installation and Connections ❹ Connecting a document camera You can connect a document camera and project printed documents, etc. COMPUTER IN NOTE: • Name, position, and direction of terminals are vary depending on camera model. Please check user’s manual of your camera for details. BNC (male) and RCA (male) conver- sion cable (not supplied) VIDEO Computer cable (not supplied) •...

  • Page 153: ❺ Connecting To A Wired Lan

    6. Installation and Connections ❺ Connecting to a Wired LAN The projector comes standard with a Ethernet/HDBaseT port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [NETWORK SETTINGS] →...

  • Page 154: ❻ Connecting To A Hdbaset Transmission Device (Sold Commercially)

    6. Installation and Connections ❻ Connecting to a HDBaseT transmission device (sold commercially) HDBaseT is a connection standard for home appliances that is established by the HDBaseT Alliance. Use a LAN cable sold commercially to connect the Ethernet / HDBaseT port of the projector (RJ-45) to a HDBaseT transmission device sold commercially.

  • Page 155: ❼ Portrait Projection (Vertical Orientation)

    6. Installation and Connections ❼ Portrait projection (vertical orientation) If you install the projector vertically you can project screens from your computer and other sources in portrait orientation. Precautions during installation • Do not simply set the projector vertically on the floor or on a table. The projector may fall over, resulting in injury, damage or malfunction.
  • Page 156 6. Installation and Connections Design and manufacturing conditions for the projector stand Please hire an installation service provider (for a fee) to design and manufacture a customized stand. Please ensure that the design complies with the following conditions: • There is one intake vent on either side and one exhaust vent at the rear. These should remain unobstructed. Also, secure enough space for easy filter cover removal for filter cleaning.

  • Page 157: Maintenance

    7. Maintenance This section describes the simple maintenance procedures you should follow to clean the filters, the lens, and the cabinet. ❶ Cleaning the Filters The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter is dirty or clogged, your projector may overheat.
  • Page 158 7. Maintenance 2. Undo the lock lever on the filter cover and remove it. If the filter gets caught on the filter cover, press the filter cover down slightly and it will come out. 3. Remove the filters. (1)Turn the tabs to the left position and slide the top filter to the right.
  • Page 159 7. Maintenance Remove the dust from the grates on the outside of the projec- tor as well. • Some intake vents do not have grates. Be sure to also remove any dust stuck to the louver (blind with angled horizontal slats) with a vacuum cleaner. NOTE: • Whenever you vacuum the filter, use the soft brush attachment to vacuum. This is to avoid damage to the filter.
  • Page 160 7. Maintenance (4)Turn the fine grade filter so it is facing upward, set the cutout portion of the medium grade filter inside the filter Cutout portion cover along the direction indicated by the tabs, and slowly slide the filter in. Direction tabs (5)Lock the lever, and insert it into the lock slot on the fine grade filter.

  • Page 161: ❷ Cleaning The Protection Glass

    7. Maintenance ❷ Cleaning the Protection glass • Turn off the projector before cleaning. • Use a blower or lens paper to clean the protection glass, and be careful not to scratch or mar the protection glass. WARNING • Do not look into the light source while the projector is ON. Strong light is emitted from the projector and visual impairment could result.

  • Page 162: User Supportware

    • To connect the projector to the network by using the Virtual Remote Tool, PC Control Utility Pro 4, PC Control Utility Pro 5, please configure the settings of [SETUP] → [NETWORK SETTINGS] in the on-screen menu (→ page 115). Download service For the update information about these software programs, visit our website: URL: http://www.nec-display.com/dl/en/index.html Operating Environment [Windows] Supported OS Windows 8.1, Windows 8.1 Pro, Windows 8.1 Enterprise, Windows 8, Windows 8 Pro, Windows 8 Enterprise...

  • Page 163: ❷ Installing Software Program

    XP Professional, “Microsoft .NET Framework Version 2.0” is required. The Microsoft .NET Framework Version 2.0, 3.0 or 3.5 is available from Microsoft’s web page. Download and install it on your computer. 1. Connect your computer to the internet and visit our website (http://www.nec-display.com/dl/en/index.html). 2. Download the supported software programs from “Download” and save an “.exe” file to your computer. File name is different depending on the version of the software program.
  • Page 164 1. Put the “PC Control Utility Pro 5” folder to the Trash icon. 2. Put the configuration file of PC Control Utility Pro 5 to the Trash icon. • The configuration file of PC Control Utility Pro 5 is located in “/Users/<your user name>/Application Data/NEC Projector User Supportware/PC Control Utility Pro 5”.

  • Page 165: ❸ Operating The Projector Via The Lan (Virtual Remote Tool)

    This section provides an outline of preparation for use of Virtual Remote Tool. For information on how to use Virtual Remote Tool, see Help of Virtual Remote Tool. (→ page 152) NOTE: • Logo data (graphics) that can be sent to the projector with Virtual Remote Tool has the following restrictions: (Only via serial or LAN connection) * File size: Within 256 kilobytes * Image size: Within the resolution of the projector * File format: PNG (Full color) • Logo data (image) sent using the Virtual Remote Tool will be displayed in the center with the surrounding area in black. • To put the default “NEC logo” back in the background logo, you need to register it as the background logo by using the image file (¥Logo¥NEC_logo2012_1920x1080.png) included on the supplied NEC Projector CD-ROM.

  • Page 166: Connect The Projector To A Lan

    Windows Desktop. Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
  • Page 167 The Help screen will be displayed. • Displaying the help file using the Start Menu. 1. Click “Start”.“All programs” or “Programs”.“NEC Projector User Supportware”.“Virtual Remote Tool”. and then “Virtual Remote Tool Help” in this order. The Help screen will be displayed.

  • Page 168: ❹ Controlling The Projector Over A Lan (Pc Control Utility Pro 4/Pro 5)

    ❹ Controlling the Projector over a LAN (PC Control Utility Pro 4/ Pro 5) Using the utility software “PC Control Utility Pro 4” or “PC Control Utility Pro 5” included on the companion NEC Pro- jector CD-ROM, the projector can be controlled from a computer over a LAN.
  • Page 169 “[NETWORK SETTINGS]” (→ page 115) (Using on Windows) Step 3: Start PC Control Utility Pro 4 Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” → “PC Control Utility Pro 4”. NOTE: • For the Schedule function of the PC Control utility Pro 4 to work, you must have your computer running and not in standby/...
  • Page 170 8. User Supportware (Using on Mac OS) Step 3: Start PC Control Utility Pro 5 1. Open your Applications folder in Mac OS. 2. Click the “PC Control Utility Pro 5” folder. 3. Click the “PC Control Utility Pro 5” icon. PC Control Utility Pro 5 will start.

  • Page 171: Appendix

    9. Appendix ❶ Throw distance and screen size Four separate bayonet style lenses can be used on this projector. Refer to the information on this page and use a lens suited for the installation environment (screen size and throw distance). For installation and replacement of lens units contact your dealer.

  • Page 172: Tables Of Screen Sizes And Dimensions

    9. Appendix Projection range for the different lenses NP-9LS13ZM1 3.1–24.8 m NP-9LS08ZM1 1.4–18.1 m 100-500 " 70-600 " 100-500 100-500 " " NP-9LS12ZM1 2.8–20.2 m NP-9LS16ZM1 3.8–31.9 m Tables of screen sizes and dimensions Size (inches) Screen width Screen height (inches) (cm) (inches)

  • Page 173: Lens Shifting Range

    9. Appendix Lens shifting range This projector is equipped with a lens shift function for adjusting the position of the projected image by using the LENS SHIFT buttons (→ page 22). The lens can be shifted within the range shown below. NOTE: • Please do not use the lens shift function when projecting portrait images. Please use it with the lens in the center.

  • Page 174: ❷ Mounting The Optional Board (Sold Separately)

    9. Appendix ❷ Mounting the Optional Board (sold separately) CAUTION Before mounting or removing the optional board, be sure to turn off the projector, wait for the fans to stop and turn off the main power switch. Tool needed: Phillips screwdriver (plus-head) 1.
  • Page 175 9. Appendix 4. Tighten the two screws on both sides of the slot. • Be sure to tighten the screws. This will complete installation of the optional board. To select the optional board source, select SLOT as the input. NOTE: • Mounting the optional board may cause the fans to run in the standby mode for the purpose of cooling depending on the optional board. The fan speed may also increase in order to cool the projector properly. Both of these instances are considered normal and not a malfunction of the projector.

  • Page 176: ❸ Compatible Input Signal List

    9. Appendix ❸ Compatible Input Signal List Analog Computer Signal Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 640 × 480 4 : 3 60/72/75/85/iMac SVGA 800 × 600 4 : 3 56/60/72/75/85/iMac 1024 × 768 4 : 3 60/70/75/85/iMac XGA+...
  • Page 177 9. Appendix HDMI Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 640 × 480 4 : 3 SVGA 800 × 600 4 : 3 1024 × 768 4 : 3 1280 × 720 16 : 9 1280 ×...
  • Page 178 9. Appendix DisplayPort Signal Resolution ( dots ) Aspect Ratio Refresh Rate ( Hz ) 640 × 480 4 : 3 SVGA 800 × 600 4 : 3 1024 × 768 4 : 3 1280 × 720 16 : 9 1280 ×...

  • Page 179: ❹ Specifications

    9. Appendix ❹ Specifications Model name PH1202HL1 Method 3 chip DMD reflection type Specifications of main parts DMD panel Size 0.65" (aspect ratio: 16:9) Pixels 2,073,600 (1920 dots × 1080 lines) (*1) Projection lenses Zoom Power zoom (zoom range depends on lens)
  • Page 180 9. Appendix Model name PH1202HL1 Ethernet/HDBaseT port RJ-45 × 1, Supports BASE-TX 3D SYNC output terminal 5 V / 10 mA, synchronized signal output for 3D use Control Terminals Remote terminal Stereo mini jack × 1 RS-232C terminal (PC control) D-Sub 9-pin ×...
  • Page 181 9. Appendix Option lens (sold separately) NP-9LS08ZM1 Power lens shift, Power zoom, Power focus, [LENS MEMORY] support (Throw ratio 0.90–1.35:1, F2.5/3.0, f = 0.5–0.8"/13.3–19.9 mm) Screen size (throwing distance): 70 - 600 inch, 1.4 - 18.1 m NP-9LS12ZM1 Power lens shift, Power zoom, Power focus, [LENS MEMORY] support (Throw ratio 1.27–1.82:1, F2.5/2.5, f = 0.7–1.1"/18.6–26.7 mm) Screen size (throwing distance): 100 - 500 inch, 2.8 - 20.2 m NP-9LS13ZM1...

  • Page 182: ❺ Cabinet Dimensions

    9. Appendix ❺ Cabinet Dimensions Unit: mm (inch) 680 (26.8) 683 (26.9) Lens center 45.2 (1.8) 566 (22.3)
  • Page 183 9. Appendix Figure for securing the unit with dimensions Unit: mm (inch) 6 - M6 screw Maximum depth 10 mm 140 (5.5) 140 (5.5)

  • Page 184: ❻ Pin Assignments And Signal Names Of Main Terminals

    9. Appendix ❻ Pin assignments and signal names of main terminals COMPUTER IN/ Component Input Terminal (Mini D-Sub 15 Pin) Connection and signal level of each pin Pin No. RGB Signal (Analog) YCbCr Signal 11 12 13 14 15 Green or Sync on Green Blue Ground Signal Level...
  • Page 185 9. Appendix Ethernet/HDBaseT Port (RJ-45) Pin No. Signal TxD+/HDBT0+ 1 2 3 4 5 6 7 8 TxD−/HDBT0− RxD+/HDBT1+ Disconnection/HDBT2+ Disconnection/HDBT2− RxD−/HDBT1− Disconnection/HDBT3+ Disconnection/HDBT3− USB Port (Type A) Pin No. Signal D− Grounding RS-232C terminal (PC control) (D-Sub 9 Pin) Pin No.
  • Page 186 9. Appendix 3D connector (D-sub 15 pin) 15 14 13 12 11 10 Pin No. Signal Name Function +12V Supplies power (+12V) to the 3D image system GNDC Ground GNDC Ground reserved reserved reserved CONN_SYNC+ 3D L/R switching timing signal (+) (Connects to the collector of the output transistor of the photo coupler inside the projector) reserved...
  • Page 187 9. Appendix GP I/O terminal (External control) (D-sub 37 pin) 19 18 17 16 15 14 13 12 11 10 37 26 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 Pin No. Signal Name Pin No.
  • Page 188 9. Appendix GP I/O Connector Inside Projector Resist = 360 Ω Ext_GPIN_P Pin No.: Voltage applied across the pins of Ext_GPIN_P and Ext_GPIN_N should be in the range from 3.3 Vdc to 10 Vdc. Recommended Operating Current: 5 mA Absolute Maximum Rating: 23 mA Ext_GPIN_N Pin No.: 24 25 26 27 Photo-coupler...
  • Page 189 9. Appendix Timing chart of GPIO control Example of Select HDMI Off at least 300 ms at least 300 ms approx. 300 ms 5-24/7-26 6-25/8-27 time Execute Select HDMI...

  • Page 190: ❼ Troubleshooting

    Red (4 times Problem with the fan Rotation of the cooling fan has stopped. Contact the NEC per cycle) projector customer support center to arrange for repair. Red (6 times Problem with the light Problem with the light source system.
  • Page 191 Temperature problem The temperature protector has been activated. If the room of 2) temperature is high, move the projector to a cool place. If the problem still persists, contact an NEC projector cus- tomer support center. Orange High surrounding tem- The surrounding temperature is high.

  • Page 192: Common Problems & Solutions

    9. Appendix Common Problems & Solutions (→ “POWER/STATUS/LIGHT/TEMP./SHUTTER/KEY LOCK Indicator” on page 175, 176.) Problem Check These Items Does not turn on • Check that the power cord is plugged in and that the power button on the projector cabinet or the remote or shut down control is on. (→ pages 13, 14) • Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room where you are presenting is particularly warm, move the projector to a cooler location. • The light module may fail to light. Wait a full minute and then turn on the power again.
  • Page 193 9. Appendix Problem Check These Items Remote control does • Install new batteries. (→ page 10) not work • Make sure there are no obstacles between you and the projector. • Stand within 42.21 ft (15 m) of the projector. (→ page 11) Indicator is lit or • See the POWER/STATUS/LIGHT/TEMP./SHUTTER/KEY LOCK Indicator. (→ page 175, 176) blinking Cross color in RGB • Press the AUTO ADJ. button on the projector cabinet or the remote control. (→ page 25) mode • Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (→...

  • Page 194: If There Is No Picture, Or The Picture Is Not Displayed Correctly

    “Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.

  • Page 195: ❽ Pc Control Codes And Cable Connection

    9. Appendix ❽ PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON POWER OFF INPUT SELECT HDMI INPUT SELECT DisplayPort INPUT SELECT BNC INPUT SELECT BNC(CV) INPUT SELECT BNC(Y/C) INPUT SELECT COMPUTER INPUT SELECT HDBaseT INPUT SELECT SLOT PICTURE MUTE ON PICTURE MUTE OFF...

  • Page 196: ❾ Troubleshooting Check List

    9. Appendix ❾ Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently.
  • Page 197 Native resolution: Refresh rate: Video adapter: Other: Projector Video equipment Blu-ray player VCR, Blu-ray player, Video camera, Video game or other Manufacturer: Signal cable Model number: NEC standard or other manufacturer’s cable? Model number: Length: inch/m Distribution amplifier Model number: Switcher Model number: Adapter Model number:...
  • Page 198 © NEC Display Solutions, Ltd. 2015 7N952401...

Table of Contents