Honeywell V-Plex DT8050A-SN Quick Installation Manual page 3

Motion sensor with anti-mask

Hide thumbs

page of 4

/ 4
Bookmarks

1. Ligue o sensor. A inicialização é concluída quando o LED para de

piscar lentamente (em cerca de 30 segundos).

2. Gire a sensibilidade de micro-ondas no sentido anti-horário para reduzir

o alcance de micro-ondas (no mínimo 16,4'/5 m) e feche o sensor.

3. Caminhe pela área de detecção e observe o LED.

4. Ajuste o alcance de micro-ondas conforme necessário para atender aos

requisitos de instalação.

O sistema fica ativo no modo de teste de caminhada por 10 minutos, sai

automaticamente do modo de teste, desativa o LED e entra no modo de

operação normal.

Para um teste adicional de 10 minutos, ative o modo de teste de caminhada novamente com o recurso lanterna.

Observação: Durante a inicialização e modos de teste de caminhada, o LED fica ativo independentemente da configuração do interruptor DIP de

ativar/desativar LED.

Top View

40'

Vue de dessus

12 m

Vista Desde Arriba

33'

Vista Superior

10 m

8 m

20'

6 m

13'

4 m

2 m

PLAN VIEW

ALL ZONES

2 m

13'

4 m

20'

6 m

8 m

33'

10 m

40'

12 m

13'

2 m

4 m

FEDERAL COMMUNICATIONS COMMISSION STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.

Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your

information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the

manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for

a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection

against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada's license-exempt RSSs. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference

that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d'Industrie Canada. Son fonctionnement est soumis aux

conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris

les interférences causant une réception indésirable.

Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures.

Exposition aux Fréquences Radio : La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8

pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de

produit multi transmetteur FCC et ISED.

La(s) antena(s) usada(s) para este transmisor se debe(n) instalar a una distancia de separación de 7,8 pulgadas (20 cm) como mínimo de todas las personas y no

debe(n) ubicarse al lado ni operar en conjunto con ningún otro transmisor, salvo de acuerdo con los procedimientos de productos multitransmisores de la FCC y ISED.

A antena usada para este transmissor deve ser instalada para fornecer uma distância de pelo menos 20 cm (7,8 polegadas) de todas as pessoas e não deve ser

Localizado ao lado ou operado em conjunto com qualquer outro transmissor, exceto de acordo com a FCC e ISED, procedimentos para produtos de múltiplos

transmissores.

Side View

Vue de coté

Vista Lateral

20'

33'

40'

46'

53'

6 m

8 m