Boutside Back Exhaust; Outside Back Exhaust; Remove Blower Plate - Frigidaire LFMV1846VFA Installation Instructions Manual

OUTSIDE BACK EXHAUST

B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
REA D IT IS VER
AND FOLL Y IMPO RTAN
IN THE OW THE T TO
BEFO INST ALLA DIRE CTIO
RE PRO TION INST NS
REA R CEE DING RUC TION
WAL L TEM PLAT WITH S
This Rear E. THIS 3/8" TO EDGE
mounti ng plate Wall Templa
outlet. and to te serves to positio 12"
1. Use locate the n the bottom
a level to check horizon tal exhaus
accura tely. that the t
2. Locate and mark templa te is positio
right side at least ned   
  of the centerl one stud 4"
I t is importa ine. on the left or
screw mounte nt to use     
of the microw d firmly in a stud at least one wood   
locatio ns ave. Mark to suppor   
3. Drill for the supplie two additio t the weight   
holes in the marked d toggle nal, evenly spaced   
a stud, drill a 3/16" locatio ns. bolts.
that do not line hole for Where 
toggle up with wood screws there is
  bolts. a stud, drill 5/8" . For holes   
AT THIS D O NOT holes for 
TIME. INSTA LL THE MOUN  
4. Remov e the templa TING PLATE 
5. Review te from  
installa the Installa the rear 
tion situatio tion Instruc tion book wall.
n. for your
Darle vuelta
a la hoja
versió n en Españ para consu
ol. ltar la
Loca te  
and mark    
moun ting holes to     
plate . align with    
IMPO RTAN holes in      
T: the       
LOC ATE     
THE CEN AT LEAS   
T ONE
MAR K TERL INE. STUD ON EITH  
THE LOC ER SIDE      
SPAC ATIO N OF
ED TOG FOR 2
ARE A. GLE BOLT ADD ITION
S IN THE AL, EVEN     
MOU NTIN LY
G PLAT
E
    

Trim the
rear wall
temp late
alon g
the dotte
d line.

Loca te
 and mark
moun ting
plate .
IMPO RTAN
T:
LOC ATE
AT LEAS
THE CEN
TERL INE.
MAR K THE LOC
SPAC
 ED TOG
ARE A.

•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
IN THE INSTALLATIO
BEFORE PROCEEDING
REAR WALL TEMPLATE.
This Rear Wall Template
mounting plate and to locate
outlet.
1. Use a level to check that
accurately.
2. Locate and mark at least
right side of the centerline.
screw mounted firmly in
of the microwave. Mark
locations for the supplied
3. Drill holes in the marked
a stud, drill a 3/16" hole
that do not line up with
toggle bolts.
AT THIS TIME.
4. Remove the template
5. Revie
installation situation.
Darle vuelta a la hoja
versión en Español.
Locate and mark holes
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
THE CENTERLINE.
MARK THE LOCATION
SPACED TOGGLE BOLTS
AREA.
Trim the rear wall template
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
align with
holes in
the
T ONE
STUD
ON EITH
ATIO N ER SIDE
FOR 2 OF
GLE BOLT ADD ITION
S IN THE AL, EVEN
MOU NTIN LY
G PLAT
E

(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
THE DIRECTIONS
N INSTRUCTION S
WITH THIS
4"
serves to position the bottom
the horizontal exhaust
the template is positioned
one stud on the left or
least one wood
It is important to use at
a stud to support the weight
two additional, evenly spaced
toggle bolts. locations. Where there is
for wood screws. For holes
a stud, drill 5/8" holes for
DO NOT INSTALL THE MOUNTING PLATE
from the rear wall.
book for your
w h t e Installation Instruction
para consultar la
to align with holes in the
STUD ON EITHER SIDE OF
FOR 2 ADDITIONAL, EVENLY
IN THE MOUNTING PLATE
to align with holes in the
Locate and mark holes
. e
m o u t n n i g l p t a
IMPORTANT: STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE. EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION IN THE MOUNTING PLATE
along the dotted line. SPACED TOGGLE BOLTS
AREA.
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16

REMOVE BLOWER PLATE

Back of
Microwave