Subscribe to Our Youtube Channel
Related Manuals for Hillstone SG-6000 E Series
Summary of Contents for Hillstone SG-6000 E Series
- Page 1 Hillstone StoneOS User Manual Hillstone SG-6000 E-Series Hardware Reference Guide www.hillstonenet.com TWNO: TW-HW-ES-EN-V5.4-Y20M05...
- Page 2 Hillstone SG-6000 E-Series Hardware Reference Guide Name and Concentration of Toxic or Hazardous Substances and Elements in Products Toxic or hazardous substances and elements Component Lead Mercury Cadmium Cr6+ PDBE Metal parts Χ (including fasteners) Printed circuit board assemblies and Χ...
-
Page 3: Preface
Preface About This Guide Thanks for choosing the network security products from Hillstone Networks. This document is an installation guide for Hillstone devices to help you install the Hillstone device properly. This guide includes the following chapters: Chapter 1. Introduction ... -
Page 4: Table Of Contents
Hillstone SG-6000 E-Series Hardware Reference Guide Table of Contents HILLSTONE SG-6000 E-SERIES HARDWARE REFERENCE GUIDE ............. 1 NAME AND CONCENTRATION OF TOXIC OR HAZARDOUS SUBSTANCES AND ELEMENTS IN PRODUCTS ..... 2 PREFACE .................................. 3 ................................3 BOUT UIDE ..............................3... - Page 5 Hillstone SG-6000 E-Series Hardware Reference Guide Connecting the Ethernet Cable ..........................38 Connecting an AC Power Cable ..........................40 Connecting a DC Power Cable ........................... 41 Connecting a Power Adapter ............................ 42 ..............................42 NSTALLING AN NTENNA SIM C ..............................43 NSTALLING THE ..............................
- Page 6 Hillstone SG-6000 E-Series Hardware Reference Guide List of Figures Figure 1-1：SG-6000-E6360 Front Panel ..............1 Figure 1-2: SG-6000-E6160 Front Panel ..............2 Figure 1-3：SG-6000-E5960 Front Panel ..............3 Figure 1-4: SG-6000-E5560 Front Panel ..............3 Figure 1-5: Front Panel of SG-6000-E3960 ..............4 Figure 1-6: Front Panel of SG-6000-E3662 ..............
- Page 7 Hillstone SG-6000 E-Series Hardware Reference Guide List of Tables Table 1-1: SG-6000-E6360 Front Panel Description ....................2 Table 1-2: SG-6000-E6160 Front Panel Description ....................2 Table 1-3: SG-6000-E5960 Front Panel Description ....................3 Table 1-4: SG-6000-E5560 Front Panel Description ....................4 Table 1-5: SG-6000-E3960 Front Panel Description ....................
-
Page 8: Hillstone Sg-6000 E-Series Hardware Reference Guide
For the supported versions of the devices, refer to Supported Versions of Devices Hardware Overview Hillstone devices are designed to fit in standard 19-inch cabinets/racks. A device can be installed in a cabinet/rack or placed on a workbench. Front Panel... -
Page 9: Name And Concentration Of Toxic Or Hazardous Substances And Elements In Products
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-1: SG-6000-E6360 Front Panel Description Label Label Label PWR: Power LED FAN: Fan LED HA: HA port e0/0 - e0/1: Gigabit STA: Status LED CLR: CLR button Ethernet ports CON: Console XLe0/2-XLe0/3: ALM: Alarm LED... -
Page 10: Document Conventions
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E5960, SG-6000-E5760 and SG-600-E5660 have the same front panel. The front panel consist of 4 Gigabit Ethernet ports, 4 SFP ports, 1 USB port, 1 HA port, 1 Management port, 1 Console port, 1 Auxiliary port, 1 CLR button, 4 general expansion slots and several LED indicators. -
Page 11: Table Of Contents
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-4: SG-6000-E5560 Front Panel Description Label Label Label e0/ - e0/3: Gigabit PWR: Power Ethernet ports (e0/2 and CLR: CLR button e0/3 support the Bypass function) STA: Status CON: Console port e0/4 - e0/7: SFP ports... -
Page 12: Figure 1-6: Front Panel Of Sg-6000-E3662
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-5: SG-6000-E3960 Front Panel Description Label Label Label e0/0 - e0/5: Gigabit PWR: Power CON: Console Ethernet ports (e0/0 and port e0/1 supports the Bypass function) STA: Status AUX: Auxiliary e0/6 - e0/9: SFP ports... -
Page 13: List Of Figures
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E2800 and SG-6000-E2300 have the same front panel. The front panel consists of 5 Gigabit Ethernet ports, 4 Combo ports (Ethernet port + SFP port), 1 USB port, 1 Console port, 1 CLR button and some LED indicators. -
Page 14: List Of Tables
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-8: SG-6000-E1700 Front Panel Description Label Label Label PWR: PS0: Power supply PS0 CON: Console port Power LED STA: Status PS1: Power supply PS1 USB: USB port ALM: Alarm e0/0 - e0/8: Gigabit... -
Page 15: Figure 1-12: Front Panel Of Sg-6000-E1100 (4G Version)
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version) Label Label Label PWR: Power WLAN: STA: Status LED WLAN LED ALM: Alarm e0/0 - e0/8: Gigabit Ethernet port status LED The front panel of SG-6000-E1100 (4G version) consists of some LED indicators. -
Page 16: Back Panel
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-13: Front Panel Description of SG-6000-E1100 (WLAN+4G version) Label Label Label PWR: Power STA: Status LED 4G: 4G LED ALM: Alarm e0/0 - e0/8: Gigabit Ethernet WLAN: port status LED WLAN LED Back Panel SG-6000-E6368, SG-6000-E6360, SG-6000-E6168 and SG-6000-E6160 have the same back panel layout. -
Page 17: Figure 1-15: Sg-6000-E5960 Back Panel
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-15: SG-6000-E5960 Back Panel SG-6000-E5568, SG-6000-E5560, SG-6000-E5268, SG-6000-E5260, SG-6000- E5168 and SG-6000-E3965 have the same back panel. The back panel consists of 2 power supply sockets, 1 grounding screw and 1 anti-dust mesh. The standard product of SG-6000- E5568/E5560/E5268/E5260/E5158/E3965 adopts dual power supplies and it is also available in single power supply. -
Page 18: Figure 1-19: Sg-6000-E1100 (Wlan Version) Back Panel
Hillstone SG-6000 E-Series Hardware Reference Guide Table 1-14: Back Panel Description of SG-6000-E1600 Label Label Label DC POWER: DC e0/0 - e0/8: Gigabit CON: Console port power interface Ethernet port CLR: CLR button USB: USB port Security keyhole SG-6000-E1100 (WLAN version) uses the power adapter. The back panel of SG-... -
Page 19: Figure 1-21: Sg-6000-E1100 (4G Version) Back Panel
Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E1100 (4G version) uses the power adapter. The back panel of SG-6000- E1100 (4G version) has 1 power supply socket, 1 Console port, 1 CLR button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security keyhole, and 2 SMA connectors for 4G antennas. -
Page 20: Led Indicators
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-22: SG-6000-E1100 (WLAN+4G version) Back Panel Table 1-18: Back Panel Description of SG-6000-E1100 (WLAN+4G version) Label Label Label SMA connector SIM: SIM card slot Security keyhole for 4G antenna DC POWER: DC SMA connectors for... - Page 21 Hillstone SG-6000 E-Series Hardware Reference Guide Orange/Always The trial license has expired and there is no legitimate license installed in the system. The system is running normally. Green/Always Power Supply PS0 is running normally. Orange/Always Power Supply PS0 is running normally, but its fan has failed.
-
Page 22: System Parameters
As the number and type of LED indicators may vary from different product models, please refer to the actual product. System Parameters The following table lists the system parameters of Hillstone devices of all models. Table 1-20: System Parameters Item... - Page 23 Hillstone SG-6000 E-Series Hardware Reference Guide 4 Gigabit Ethernet ports 4 SFP ports 1 USB 2.0 Host port SG-6000-E5960 SG-6000-E5760 1 MGT port SG-6000-E5660 1 HA port 1 Console port 1 Auxiliary port 4 Gigabit Ethernet ports SG-6000-E5568 4 SFP ports...
- Page 24 Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E6368 SG-6000-E6360 32GB SG-6000-E6168 SG-6000-E6160 SG-6000-E5960 SG-6000-E5760 SG-6000-E5660 16 GB SG-6000-E5568 SG-6000-E5560 SG-6000-E5268 SG-6000-E5260 8 GB SG-6000-E5168 SG-6000-E3965 SG-6000-E3968 SG-6000-E3960 DDR SDRAM SG-6000-E3668 4 GB SG-6000-E3662 SG-6000-E2868 SG-6000-E2860 SG-6000-E3660 SG-6000-E2800 SG-6000-E2300 2 GB SG-6000-E1700...
- Page 25 Hillstone SG-6000 E-Series Hardware Reference Guide SG-6000-E1100 (WLAN version) SG-6000-E1100 (4G version) SG-6000-E1100 (WLAN+4G version) SG-6000-E6368 SG-6000-E6360 440.0mm x 455.0mm x SG-6000-E6168 110.0mm SG-6000-E6160 SG-6000-E5960 440.0 mm x 520.0 mm x SG-6000-E5760 88.0 mm SG-6000-E5660 SG-6000-E5568 SG-6000-E5560 SG-6000-E5268 440.0mm x 530.0mm x 88.0mm...
- Page 26 Hillstone SG-6000 E-Series Hardware Reference Guide Gross weight: 16.8 kg(accessories and packages included) SG-6000-E5568 SG-6000-E5560 Net weight: 11.8 kg SG-6000-E5268 Gross weight: 16.3 kg SG-6000-E5260 (accessories and packages included) SG-6000-E5168 SG-6000-E3965 SG-6000-E2800 Net weight: 2.5 kg SG-6000-E2300 Gross weight: 5.3 kg...
-
Page 27: Ports
USB port, gigabit copper port, SFP port， QSFP+ ports and XFP port. Console Port Hillstone device provides an RS-232C asynchronous serial console port for you to configure the device. Attributes for the console (CON) port are shown in the following table. -
Page 28: Table 1-23: Usb Port Attributes
Hillstone SG-6000 E-Series Hardware Reference Guide USB Port Hillstone device provides up to two USB host ports. Attributes for the USB port are shown in the following table. Table 1-23: USB Port Attributes Attribute Description Connector USB Type-A interface Port Standard USB 2.0 host interface... -
Page 29: Table 1-26: Sfp Optical Module Attributes
TRAN-LX80 —— Factory Module Caution: When using the optical module of Hillstone Network factory, it is recommended not to mix with other manufacturers' optical modules, otherwise some abnormal problems may arise If you choose to use copper SFP transceiver in SFP port, you should use crossover or straight-through cable (i.e. -
Page 30: Table 1-27: Sfp Copper Module Attributes
10Gbps Mode If you choose to use SFP+ optical module in SFP+ port, you should use LC-Type optical connector. Hillstone device supports four types of 10G Base-FX SFP+ optical modules. All optical modules are hot-swappable. Caution: To avoid dust falling into the SFP+ socket, you should place a rubber dust ... -
Page 31: Table 1-29: Sfp+ Optical Module Attributes
Optional Factory TRAN-SR-SFP+ TRAN-LR-SFP+ TRAN-SFP+-LX40 TRAN-SFP+-LX80 Module Caution: When using the optical module of Hillstone Network factory, it is recommended not to mix with other manufacturers' optical modules, otherwise some abnormal problems may arise QSFP+ Port Table 1-30: QSFP+ Port Attributes... -
Page 32: Table 1-31: Qsfp+ Optical Module Attributes
Optional Factory TRAN-SR-QSFP+ TRAN-LR-QSFP+ Module Caution: When using the optical module of Hillstone Network factory, it is recommended not to mix with other manufacturers' optical modules, otherwise some abnormal problems may arise XFP Port Hillstone devices support XFP ports which use XFP optical modules. -
Page 33: Clr Button
TRAN-XFP-LR LR40 LR80 Module Caution: When using the optical module of Hillstone Network factory, it is recommended not to mix with other manufacturers' optical modules, otherwise some abnormal problems may arise CLR Button The CLR button is the pinhole of the front panel and is used to reset the device back to the factory default settings. -
Page 34: Expansion Slot
Cautions: Cover the expansion slot with blank panel if the slot has no expansion module installed. For detailed information of expansion modules, see Hillstone SG-6000 M_G_E Series Expansion Modules Reference Guide. Power Supply Single/Dual power supply: Some product modules adopt single power supply, while others adopt dual power supplies, i.e. -
Page 35: Table 1-34: Power Supplies Of All Product Models
External version) Power Module Hillstone designs a model of pluggable module for SG-6000-E6368, SG-6000- E6360, SG-6000-E6168, SG-6000-E6160, SG-6000-E5960, SG-6000-E5760, SG- 6000-E5660, SG-6000-E5268, SG-6000-E5260, SG-6000-E5168 and SG-6000- E3965. Both AC and DC power modules are available. You can choose the power type at your own choice. -
Page 36: Hard Disk Modules
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 1-23: AC Power Module Figure 1-24: DC Power Module The power LED description for is listed in the following table. Table 1-35: Power Supply Module LED Descriptions Color/Status Description Green/Always on Power module is functioning normally. -
Page 37: Expansion Modules
4 small fans. The anti-dust mesh is vertically installed on the right side of the back panel and it is the air intake vent. Hillstone suggest purchasing an auxiliary anti- dust mesh for the situation that the original anti-dust mesh is sent to Hillstone for Chapter 1 Introduction... - Page 38 Besides, it is recommended that you should replace the anti-dust mesh every 3 or 6 months according to the clearness status of your equipment room. To purchase a new anti-dust mesh, contact Hillstone. SG-6000-E3968/E3960/E3960-GM/E3668/E3662/E3662-GM/SG-6000- E3660/E2868/E2860/E2300/2800 has a built-in cooling system.
-
Page 39: Chapter 2 Installation Preparations
To prevent personnel injury and equipment damage, please carefully read all the safety warnings and cautions in this chapter before the installation. Hillstone products are designed for indoor use. To ensure the normal operation and to prolong the service lifetime, the installation site must meet the following... -
Page 40: Grounding Requirements
If you have any problem, please contact your sales representative. Installation Devices/Tools/Cables A Hillstone device is shipped with a power cable and a console cable, and you should have the following items before the installation: Chapter 2 Installation Preparations... - Page 41 Hillstone SG-6000 E-Series Hardware Reference Guide Terminal: Configuration terminal (e.g. an ordinary PC). Tools: Philips screwdrivers and ESD wrist strap. Cables: Power cable, console cable and Ethernet cable. Chapter 2 Installation Preparations Hillstone...
-
Page 42: Chapter 3 Installation
On a workbench On a standard 19-inch rack Installing the Device on a Workbench Hillstone product can be placed on a stable and clean workbench. For skid prevention, take the following steps to fit anti-skid pads on the device before installing: Step 1: Tear off the sticker from the rubber pad. -
Page 43: Installing The Device On A Rack
Installing the Device on a Rack Before mounting the device on a rack, ensure that the power is off, and the rack is stable enough and well grounded. Hillstone devices are designed for a 19-inch standard rack. To mount the chassis on a rack: Step 1: Use rack-mounting ear to mark the positions of floating nuts on the front rack posts, as shown in Figure 3-2. -
Page 44: Connecting Cables
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-3: Installing the Rack-mounting Ears (1U Chassis as example) Step 3: Two person are needed to cooperate to raise the device and place it to the tray of the rack (or two person place the device to the tray of lift first, then use the lift to achieve it). -
Page 45: Connecting The Ground Wire
Connecting the Ethernet Cable Hillstone products provide 1000Mbps electrical Ethernet ports, SFP ports, XFP ports and Ethernet Combo ports (Electrical port + Optical port). The electrical Ethernet port can be connected by a straight-through cable (also called standard cable) or a crossover cable. -
Page 46: Figure 3-6: Connecting The Ethernet Copper Cable
The XFP port uses single- mode or multi-mode cables to access Ethernet. All SFP Port and XFP Port optical modules of Hillstone products use LC-type optical connector; therefore, you should connect the optical modules using optical fiber ended with LC-type connector. -
Page 47: Connecting An Ac Power Cable
Hillstone SG-6000 E-Series Hardware Reference Guide Keep the connector of the optical cable clean. Figure 3-7: Connecting the Ethernet Fiber Cable Warning: Laser danger! To protect your eyes from radiation harm, do not stare into a cable connector connected to a laser generator. -
Page 48: Connecting A Dc Power Cable
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-8: Connecting an AC Power Cable Note: If a product does not have a power switch, you can skip Step2 and Step4. Connecting a DC Power Cable To power the device with DC power source, use DC power cables to connect the device and the external DC power source. -
Page 49: Connecting A Power Adapter
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 3-9: Connecting a DC Power Cable Connecting a Power Adapter To provide the power supply, connect the power adapter of the devices with the external AC power supply as follows: 1. Insert the DC output plug of the power adapter into the AC power interface at the back panel of the device. -
Page 50: Installing The Sim Card
Hillstone SG-6000 E-Series Hardware Reference Guide 1. According to the function you use, select the corresponding antenna. 2. Install the antenna to the SMA connector at the back panel of the device by rotating the antenna clockwise. Installing the SIM Card... -
Page 51: Chapter 4 Boot And Configuration
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 4 Boot and Configuration Introduction This chapter describes the initial system boot and basic configuration of Hillstone SG-6000 series, using a PC as the console terminal. Establishing a Configuration Environment Hillstone devices support both local and remote configuration. Administrators can use the following configuration methods. -
Page 52: Webui
If the booting succeeds, the system will display the command line prompt “login”. Enter the default administrator name and password “hillstone” at the “login” and “password” prompts, press “Enter”. And now you are successfully logged in and accessing the CLI. -
Page 53: Tenet And Ssh
Hillstone SG-6000 E-Series Hardware Reference Guide 3. Enter the default administrator name and password “hillstone” in both the Login and Password text boxes. 4. Click the Login button to enter WebUI main page. Then you can set other configurations to the device. -
Page 54: Chapter 5 Hardware Maintenance And Replacement
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 5 Hardware Maintenance and Replacement Introduction This chapter explains how to install and remove the power supply module, the expansion module and the fan tray. Installing and Removing the Power Supply Module This section describes how to install and remove the power supply module of SG-... -
Page 55: Installing And Removing The Expansion Module
Hillstone SG-6000 E-Series Hardware Reference Guide Installing and Removing the Expansion Module SG-6000-E6368, SG-6000-E6360, SG-6000-E6168, SG-6000-E6160, SG-6000- E5960, SG-6000-E5760, SG-6000-E5660, SG-6000-E5568, SG-6000-E5560, SG- 6000-E5268, SG-6000-E5260, SG-6000-E5168, SG-6000-E3965, SG-6000-E3968, SG-6000-E3960, SG-6000-E3668, SG-6000-E3662, SG-6000-E3660, SG-6000- E2868 and SG-6000-E2860 can accommodate expansion modules. This section describes how to install and remove the expansion module. -
Page 56: Installing And Removing The Anti-Dust Mesh
Hillstone SG-6000 E-Series Hardware Reference Guide 2. Pull the fan tray out of the chassis by holding the provided handle. Note: To avoid over-heating, insert a replacement fan tray immediately after removing the existing one. Installing and Removing the Anti-dust Mesh... -
Page 57: Installing And Removing The Hard Disk Module
Hillstone SG-6000 E-Series Hardware Reference Guide Installing and Removing the Hard Disk Module SG-6000-E6368, SG-6000-E6168, SG-6000-E5568, SG-6000-E5268, SG-6000- E5168, SG-6000-E3968, SG-6000-E3668, and SG-6000-E2868 are designed with the hard disk module. Take the following steps to install the hard disk module: 1. -
Page 58: Figure 5-4: Placing The Hard Disk Module
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 5-4: Placing the Hard Disk Module 5. Use the screw in the hard disk module package to fix the hard disk module. Figure 5-5: Fixing the Hard Disk Module Use a screwdriver to re-install the blank panel into the hard disk slot. -
Page 59: Figure 5-6: Installing The Blank Panel
Hillstone SG-6000 E-Series Hardware Reference Guide Figure 5-6: Installing the Blank Panel Take the following steps to remove the hard disk module: 1. Make sure the device is not powered and you have worn antistatic gloves. 2. The hard disk module is at the bottom of the device, you should turn over the device to make sure the hard disk module is visible. -
Page 60: Chapter 6 Troubleshooting
Hillstone SG-6000 E-Series Hardware Reference Guide Chapter 6 Troubleshooting Introduction This chapter provides solutions to some common problems of Hillstone devices. Losing the Administrator Password If you lose the administrator password, please contact your local sales representative. Troubleshooting Power System Check the PWR LED on the front panel of the device. -
Page 61: Appendix: Supported Versions Of Devices
You can find the production date of the device according to the SN. There is 16-digit SN on the Hillstone devices. Among it, the 6th and 7th number mean the production week and the 8th and 9th number mean the production year. Taking the SN of xxxxx4018xxxxxxx for example, the device is produced in the 40th week of 2018 year. - Page 62 Hillstone SG-6000 E-Series Hardware Reference Guide Device SN Range (Update Device Model Device Supported Versions devices to the supported (Part of devices are delisted) versions if SN is within the range) SG-6000-E3660, SG-6000- E3660S, SG-6000-E2860, SG- 6000-E3662, SG-6000-E2868, SG-6000-E3668, SG-6000-...
- Page 63 Hillstone SG-6000 E-Series Hardware Reference Guide Whether Device SN Range(Update IOC- devices to the supported Device Model 2SFP+- Device Supported Versions versions if SN is within the lite is range) Used 5.5R2P14 and later P versions 5.5R4P9 and later P versions Before xxxxx0717xxxxxxx 5.5R5P7 and later P versions...
- Page 64 Hillstone SG-6000 E-Series Hardware Reference Guide Whether Device SN Range(Update IOC- devices to the supported Device Model 2SFP+- Device Supported Versions versions if SN is within the lite is range) Used 5.5R6P2 and later P versions 5.5R7 and later versions 5.0R4P14 and later P versions...
-
Page 65: Addendum Fcc Statement
Hillstone SG-6000 E-Series Hardware Reference Guide Addendum FCC Statement Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC Statement: This device complies with Part 15 of the FCC Rules. - Page 66 Hillstone SG-6000 E-Series Hardware Reference Guide This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may not be co-located with any other transmitter or antenna.
- Page 67 Hillstone SG-6000 E-Series Hardware Reference Guide relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC) and R&TTE (1999/5/EC). The equipment passed the test which was performed according to the following European standards: •ETSI EN 300 328 V1.8.1 (2012-06) •EN 301 893 V1.7.1 (2012-06) •EN 62311: 2008...
-
Page 68: Copyright Information
Hillstone, Hillstone Networks logo, StoneOS, StoneManager, Hillstone PnPVPN, UTM Plus are trademarks of Hillstone Networks. All other trademarks or registered marks are the property of their respective owners. Hillstone Networks assumes no responsibility for any inaccuracies in this document. Hillstone Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
Need help?
Do you have a question about the SG-6000 E Series and is the answer not in the manual?
Questions and answers