Table of Contents
Advertisement
CONTENTS
Section
1
INTRODUCTION ........................................................... 1
2
SETTING UP ................................................................. 2
2.1
Instrument Power-up .......................................... 2
2.1.1
Power-up Error Codes .......................... 3
2.2
Fitting the Chart .................................................. 4
2.3
Fitting the Pen Capsule(s) ................................... 4
3
DISPLAYS & CONTROLS ............................................. 5
3.1
Displays and LED Indicators ............................... 5
3.2
Use of Controls ................................................... 7
4
GENERAL OPERATION ................................................ 8
4.1
Input Error Messages .......................................... 9
5
CONTROL OPERATION ............................................. 10
5.1
Operating Page Introduction ............................. 12
5.1.1
Set Point Tracking ............................... 12
5.1.2
Auto/Manual Transfer .......................... 12
5.1.3
Profile Control ..................................... 12
5.1.4
Cascade Control ................................. 12
5.1.5
Heat/Cool Control ............................... 12
5.2
Operating Page Displays ................................... 13
5.3
Alarm Acknowledge Page ................................. 16
5.3.1
Alarm Indications ................................. 16
5.3.2
Acknowledging Alarms ........................ 16
5.3.3
Acknowledge Page ............................. 16
5.4
Totals Page Displays ......................................... 17
5.5
Access to Configuration Levels ......................... 18
5.5.1
Security Code Page ............................ 18
5.6
Profile States Page ........................................... 19
5.7
Auto-tuning Introduction ................................... 20
5.7.1
Auto-tuning Page ................................ 21
5.8
Auto-tune Diagnostic Messages ....................... 24
5.9
Introduction to Standard Control ....................... 25
5.9.1
Control Page (Standard Control) .......... 30
5.10
Introduction to Heat/Cool Control ..................... 31
5.10.1 Control Page (Heat/Cool Control) ........ 32
5.10.2 Calculating the Crossover Value .......... 33
5.10.3 Calculating the Transition
Bandwidth Value ................................. 33
6
RECORD OPERATION ............................................... 34
6.1
Operating Page Displays ................................... 35
6.2
Alarm Acknowledge Page ................................. 36
6.2.1
Alarm Indications ................................. 36
6.2.2
Acknowledging Alarms ........................ 36
6.2.3
Using the Alarm
Acknowledge Page ............................. 36
6.3
Totals Page Displays ......................................... 37
7
SIMPLE FAULT FINDING ........................................... 38
8
SPARES LIST ............................................................. 39
1 INTRODUCTION
Page
The documentation for the C1900 series of circular chart
recorders is shown in Fig. 1.1. The
the specification sheet, are supplied with all instruments. The
Supplementary Manuals
the instrument.
INSTALLATION
Product Identification
Siting
Mounting
Electrical Connections
Installation Record
IM/C1900-INS
PROGRAMMING
General Programming
Basic Config. Level
Control Config. Level
Advanced Config. Level
Connections and Links
IM/C1900-PGC
ADVANCED SOFTWARE
OPTIONS
Flow Totalization
Ramp/Soak Profile
Math Functions
Timer Functions
IM/C1900-ADV
B - Supplementary Manuals
Fig. 1.1 C1900 Documentation
Standard Manuals
supplied depend on the specification of
OPERATION
Setting Up
Error Messages
Displays & Controls
Operating Level
Simple Fault Finding
Part No.
IM/C1900-OGC
DATA SHEET
Full Specification
Part No.
SS C1900
A - Standard Manuals
MODBUS (RTU)
Serial Adaptors
Serial Connections
Programming Pages
ASCII Tables
Part No.
IM/C1900-MOD
, including
Part No.
Part No.
Part No.
1
Advertisement
Table of Contents
