Related Manuals for Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2
Summary of Contents for Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2
- Page 1 5 GHz airMAX ac Radio ® BaseStation with airPrism ® Active RF Filtering Technology Model: RP-5AC-Gen2...
-
Page 2: Package Contents
ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable ™... -
Page 3: Hardware Overview
Hardware Overview Antenna RP-SMA RP-SMA Connector Antenna Antenna Connector: Connector: Chain 1 Chain 0 LED Panel Port Cover... - Page 4 LED Panel Signal In airOS®, you can modify the wireless signal strength threshold values for each LED on the Wireless tab under Signal LED Thresholds. The default values are shown below: LED will light blue when the wireless signal strength is above -65 dBm. LED will light blue when the wireless signal strength is above -73 dBm.
- Page 5 Ports Reset Button LAN Port Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the Rocket Prism is powered on. Alternatively, the Rocket Prism may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.
-
Page 6: Hardware Installation
Hardware Installation The Rocket Prism is designed to mount directly onto a Ubiquiti airMAX RocketDish antenna for Point-to-Point use or an ™ airMAX Sector antenna for Point-to-MultiPoint use. 1. Lift the release latch on the bottom of the Rocket Prism and slide the Port Cover off. - Page 7 4. Connect the RF cables to the RP-SMA Antenna Connectors located on top of the Rocket Prism. 5. Attach the Rocket Prism to the antenna. a. Align the mounting tabs on the back of the Rocket Prism with the mounting slots on the antenna. b.
- Page 8 6. Attach the other end of the RF cables to the RF connectors on the antenna. Connecting to a RocketDish Connecting to a Sector Antenna 7. Connect the GPS Antenna to the GPS Antenna Connector on the Rocket Prism. Connecting the GPS Antenna Connecting the GPS Antenna...
- Page 9 8. Attach the protective shroud. Align the hash mark on the top Slide the protective shroud of the shroud with the notch on down over the Rocket Prism the RocketDish. Rotate the shroud until it locks into place on the clockwise until it locks into place.
- Page 10 Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to “Connecting to the PoE Adapter” . • Using a separate PoE switch: Connect the Ethernet cable from the Rocket Prism’s Ethernet port to a PoE-enabled Ethernet port on the switch.
- Page 11 Accessing airOS via Wi-Fi Verify connectivity in the airOS Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the Rocket Prism. If necessary, you can power cycle the Rocket Prism to re-enable its Wi-Fi.
- Page 12 5. Tap Connect on the Login screen. 6. Select your Country and tap Done.
- Page 13 7. Customize your settings as needed.
-
Page 14: Web Portal
Web Portal 1. Connect your device’s Wi-Fi to the Rocket Prism SSID named: RP-5AC-Gen2:<MAC Address> Note: Ensure that your Wi-Fi connection has DHCP enabled. 2. Launch your web browser and type the following URL into the address bar: http://setup.ubnt.com http://setup.ubnt.com 3. -
Page 15: Installer Compliance Responsibility
Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna Gain and Output Power fields are provided to the professional installer to... -
Page 16: Specifications
Specifications RP-5AC-Gen2 Dimensions 88 x 40 x 230 mm (3.47 x 1.58 x 9.06") Weight 400 g (14.11 oz) Networking Interface (1) 10/100/1000 Ethernet Port RF Connectors (2) RP-SMA (Waterproof ) (1) GPS (Waterproof ) LEDs (4) Signal Strength, GPS, Power, LAN Enclosure Die-Cast Aluminum with White Powder Coating... -
Page 17: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. -
Page 18: Limited Warranty
Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;... - Page 19 No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS.
-
Page 20: Limitation Of Liability
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING... - Page 21 Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 22: Industry Canada
Industry Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. - Page 23 RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilisées pour ce transmetteur doivent être installé...
- Page 24 RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 25 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 26: Declaration Of Conformity
[German] Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Ελληνική Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις [Greek] βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ. -
Page 27: Online Resources
NETWORKS zariadenie, je v súlade so základnými požiadavkami a [Slovak] ďalšími relevantnými ustanoveniami smernice 1999/5/ES. Español Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos [Spanish] esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. - Page 28 . u b n t . c o m ©2016-2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, airPrism, Rocket, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc.